mirror of https://github.com/Desuuuu/klipper.git
133 lines
2.4 KiB
INI
133 lines
2.4 KiB
INI
# This file contains common pin mappings for the BIGTREETECH SKR Pico V1.0
|
|
# To use this config, the firmware should be compiled for the RP2040 with
|
|
# USB communication.
|
|
|
|
# The "make flash" command does not work on the SKR Pico V1.0. Instead,
|
|
# after running "make", copy the generated "out/klipper.uf2" file
|
|
# to the mass storage device in RP2040 boot mode
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: gpio11
|
|
dir_pin: !gpio10
|
|
enable_pin: !gpio12
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^gpio4
|
|
position_endstop: 0
|
|
position_max: 235
|
|
homing_speed: 50
|
|
|
|
[tmc2209 stepper_x]
|
|
uart_pin: gpio9
|
|
tx_pin: gpio8
|
|
uart_address: 0
|
|
run_current: 0.580
|
|
stealthchop_threshold: 999999
|
|
|
|
[stepper_y]
|
|
step_pin: gpio6
|
|
dir_pin: !gpio5
|
|
enable_pin: !gpio7
|
|
microsteps: 16
|
|
rotation_distance: 40
|
|
endstop_pin: ^gpio3
|
|
position_endstop: 0
|
|
position_max: 235
|
|
homing_speed: 50
|
|
|
|
[tmc2209 stepper_y]
|
|
uart_pin: gpio9
|
|
tx_pin: gpio8
|
|
uart_address: 2
|
|
run_current: 0.580
|
|
stealthchop_threshold: 999999
|
|
|
|
[stepper_z]
|
|
step_pin: gpio19
|
|
dir_pin: gpio28
|
|
enable_pin: !gpio2
|
|
microsteps: 16
|
|
rotation_distance: 8
|
|
endstop_pin: ^gpio25
|
|
position_endstop: 0.0
|
|
position_max: 250
|
|
|
|
[tmc2209 stepper_z]
|
|
uart_pin: gpio9
|
|
tx_pin: gpio8
|
|
uart_address: 1
|
|
run_current: 0.580
|
|
stealthchop_threshold: 999999
|
|
|
|
[extruder]
|
|
step_pin: gpio14
|
|
dir_pin: !gpio13
|
|
enable_pin: !gpio15
|
|
microsteps: 16
|
|
rotation_distance: 33.500
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: gpio23
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: gpio27
|
|
control: pid
|
|
pid_Kp: 21.527
|
|
pid_Ki: 1.063
|
|
pid_Kd: 108.982
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: gpio9
|
|
tx_pin: gpio8
|
|
uart_address: 3
|
|
run_current: 0.650
|
|
stealthchop_threshold: 999999
|
|
|
|
[heater_bed]
|
|
heater_pin: gpio21
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: gpio26
|
|
control: pid
|
|
pid_Kp: 54.027
|
|
pid_Ki: 0.770
|
|
pid_Kd: 948.182
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: gpio17
|
|
|
|
[heater_fan heatbreak_cooling_fan]
|
|
pin: gpio18
|
|
|
|
[heater_fan controller_fan]
|
|
pin: gpio20
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
[neopixel board_neopixel]
|
|
pin: gpio24
|
|
chain_count: 1
|
|
color_order: GRB
|
|
initial_RED: 0.3
|
|
initial_GREEN: 0.3
|
|
initial_BLUE: 0.3
|
|
|
|
#[bltouch]
|
|
#sensor_pin: gpio22
|
|
#control_pin: gpio29
|
|
|
|
#[filament_switch_sensor runout_sensor]
|
|
#switch_pin: ^gpio16
|