mirror of https://github.com/Desuuuu/klipper.git
148 lines
6.9 KiB
Markdown
148 lines
6.9 KiB
Markdown
# Pressure advance
|
|
|
|
This document provides information on tuning the "pressure advance"
|
|
configuration variable for a particular nozzle and filament. The
|
|
pressure advance feature can be helpful in reducing ooze. For more
|
|
information on how pressure advance is implemented see the
|
|
[kinematics](Kinematics.md) document.
|
|
|
|
## Tuning pressure advance
|
|
|
|
Pressure advance does two useful things - it reduces ooze during
|
|
non-extrude moves and it reduces blobbing during cornering. This guide
|
|
uses the second feature (reducing blobbing during cornering) as a
|
|
mechanism for tuning.
|
|
|
|
In order to calibrate pressure advance the printer must be configured
|
|
and operational as the tuning test involves printing and inspecting a
|
|
test object. It is a good idea to read this document in full prior to
|
|
running the test.
|
|
|
|
Use a slicer to generate g-code for the large hollow square found in
|
|
[docs/prints/square_tower.stl](prints/square_tower.stl). Use a high
|
|
speed (eg, 100mm/s), zero infill, and a coarse layer height (the layer
|
|
height should be around 75% of the nozzle diameter). Make sure any
|
|
"dynamic acceleration control" is disabled in the slicer.
|
|
|
|
Prepare for the test by issuing the following G-Code command:
|
|
```
|
|
SET_VELOCITY_LIMIT SQUARE_CORNER_VELOCITY=1 ACCEL=500
|
|
```
|
|
This command makes the nozzle travel slower through corners to
|
|
emphasize the effects of extruder pressure. Then for printers with a
|
|
direct drive extruder run the command:
|
|
```
|
|
TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START=0 FACTOR=.005
|
|
```
|
|
For long bowden extruders use:
|
|
```
|
|
TUNING_TOWER COMMAND=SET_PRESSURE_ADVANCE PARAMETER=ADVANCE START=0 FACTOR=.020
|
|
```
|
|
Then print the object. When fully printed the test print looks like:
|
|
|
|
|
|
|
|
The above TUNING_TOWER command instructs Klipper to alter the
|
|
pressure_advance setting on each layer of the print. Higher layers in
|
|
the print will have a larger pressure advance value set. Layers below
|
|
the ideal pressure_advance setting will have blobbing at the corners,
|
|
and layers above the ideal setting can lead to rounded corners and
|
|
poor extrusion leading up to the corner.
|
|
|
|
One can cancel the print early if one observes that the corners are no
|
|
longer printing well (and thus one can avoid printing layers that are
|
|
known to be above the ideal pressure_advance value).
|
|
|
|
Inspect the print and then use a digital calipers to find the height
|
|
that has the best quality corners. When in doubt, prefer a lower
|
|
height.
|
|
|
|
|
|
|
|
The pressure_advance value can then be calculated as `pressure_advance
|
|
= <start> + <measured_height> * <factor>`. (For example, `0 + 12.90 *
|
|
.020` would be `.258`.)
|
|
|
|
It is possible to choose custom settings for START and FACTOR if that
|
|
helps identify the best pressure advance setting. When doing this, be
|
|
sure to issue the TUNING_TOWER command at the start of each test
|
|
print.
|
|
|
|
Typical pressure advance values are between 0.050 and 1.000 (the high
|
|
end usually only with bowden extruders). If there is no significant
|
|
improvement with a pressure advance up to 1.000, then pressure advance
|
|
is unlikely to improve the quality of prints. Return to a default
|
|
configuration with pressure advance disabled.
|
|
|
|
Although this tuning exercise directly improves the quality of
|
|
corners, it's worth remembering that a good pressure advance
|
|
configuration also reduces ooze throughout the print.
|
|
|
|
At the completion of this test, set
|
|
`pressure_advance = <calculated_value>` in the `[extruder]` section of
|
|
the configuration file and issue a RESTART command. The RESTART
|
|
command will clear the test state and return the acceleration and
|
|
cornering speeds to their normal values.
|
|
|
|
## Important Notes
|
|
|
|
* The pressure advance value is dependent on the extruder, the nozzle,
|
|
and the filament. It is common for filament from different
|
|
manufactures or with different pigments to require significantly
|
|
different pressure advance values. Therefore, one should calibrate
|
|
pressure advance on each printer and with each spool of filament.
|
|
|
|
* Printing temperature and extrusion rates can impact pressure
|
|
advance. Be sure to tune the
|
|
[extruder rotation_distance](Rotation_Distance.md#calibrating-rotation_distance-on-extruders)
|
|
and
|
|
[nozzle temperature](http://reprap.org/wiki/Triffid_Hunter%27s_Calibration_Guide#Nozzle_Temperature)
|
|
prior to tuning pressure advance.
|
|
|
|
* The test print is designed to run with a high extruder flow rate,
|
|
but otherwise "normal" slicer settings. A high flow rate is obtained
|
|
by using a high printing speed (eg, 100mm/s) and a coarse layer
|
|
height (typically around 75% of the nozzle diameter). Other slicer
|
|
settings should be similar to their defaults (eg, perimeters of 2 or
|
|
3 lines, normal retraction amount). It can be useful to set the
|
|
external perimeter speed to be the same speed as the rest of the
|
|
print, but it is not a requirement.
|
|
|
|
* It is common for the test print to show different behavior on each
|
|
corner. Often the slicer will arrange to change layers at one corner
|
|
which can result in that corner being significantly different from
|
|
the remaining three corners. If this occurs, then ignore that corner
|
|
and tune pressure advance using the other three corners. It is also
|
|
common for the remaining corners to vary slightly. (This can occur
|
|
due to small differences in how the printer's frame reacts to
|
|
cornering in certain directions.) Try to choose a value that works
|
|
well for all the remaining corners. If in doubt, prefer a lower
|
|
pressure advance value.
|
|
|
|
* If a high pressure advance value (eg, over 0.200) is used then one
|
|
may find that the extruder skips when returning to the printer's
|
|
normal acceleration. The pressure advance system accounts for
|
|
pressure by pushing in extra filament during acceleration and
|
|
retracting that filament during deceleration. With a high
|
|
acceleration and high pressure advance the extruder may not have
|
|
enough torque to push the required filament. If this occurs, either
|
|
use a lower acceleration value or disable pressure advance.
|
|
|
|
* Once pressure advance is tuned in Klipper, it may still be useful to
|
|
configure a small retract value in the slicer (eg, 0.75mm) and to
|
|
utilize the slicer's "wipe on retract option" if available. These
|
|
slicer settings may help counteract ooze caused by filament cohesion
|
|
(filament pulled out of the nozzle due to the stickiness of the
|
|
plastic). It is recommended to disable the slicer's "z-lift on
|
|
retract" option.
|
|
|
|
* The pressure advance system does not change the timing or path of
|
|
the toolhead. A print with pressure advance enabled will take the
|
|
same amount of time as a print without pressure advance. Pressure
|
|
advance also does not change the total amount of filament extruded
|
|
during a print. Pressure advance results in extra extruder movement
|
|
during move acceleration and deceleration. A very high pressure
|
|
advance setting will result in a very large amount of extruder
|
|
movement during acceleration and deceleration, and no configuration
|
|
setting places a limit on the amount of that movement.
|