The SET_GCODE_OFFSET command could cause unwanted behavior when an
offset is applied to the following g-code command. (In particular,
when the following command is an extrude only move - as in
issue #1289.)
Don't apply the offset immediately. Instead, add support for a MOVE=1
parameter which will schedule a move to apply the given offset.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Prior to the BLTouch v3, the recommended command times were 700us
(pin_down), 1200us (touch_mode), 1500us (pin_up), 1800us (self_test),
and 2200us (reset). However, the recommended Marlin timing (via servo
"angles") was 647.111, 1162.667, 1472, 1781.333, and 2193.778us.
As of the BLTouch v3, the recommended times are now 650, 1165, 1475,
1780, and 2190us. The v3 continues to recommended Marlin timings of
647.111, 1162.667, 1472, 1781.333, and 2193.778us.
Update Klipper to use the new BL-Touch v3 recommended timing. The new
timings are required for the BL-Touch v3 and they are closer to what
the Marlin firmware has historically used.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Improve the precision of soft pwm pulses by allowing the host to
directly specify the clock duration of the pulse. This improvement in
precision may be noticeable when controller servos (and bltouch).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Mark methods internal to gcode.py with an underscore so that it is
easier to see which functions are purely helper functions.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
"The z_tilt_adjust was coded to require 3 points because the original
intent was for railcore-xl and voron. Since then, a number of users
have started using z_tilt_adjust for prusa i3 style printers with dual z
steppers. That's fine, but we just haven't gotten around to removing
the superfluous check in the code." -- Kevin O'Connor
remove that check.
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
Factor out minimum required points check for ProbePointsHelper
in prep for setting different values for quad_gantry_level
and z_tilt_adjust
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
"Feed Filament" menu item value was off-screen that made this item useless. So I changed its name to just "Feed". Users shall easily guess that this item is for filament feeding because this item is located in "Filament" menu.
Signed-off-by: Alexander Fadeev <alfsoft@gmail.com>
safety feature that prevents quad_gantry_level from trying to do a
correction that might break things - if your probe fires early for
whatever reason and tries to do an 8mm correction in one corner instead
we abort if a correction is over a configurable limit by default 4mm
configurable via `max_adjust` parameter in the config
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
In particular trying to keep the output from a single quad_gantry_level
so that it fits in the octoprint terminal window without the need to
scroll
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
Adding gcode command for setting the target temperature of temperature_fan.
Example gcode: SET_TEMPERATURE_FAN_TARGET temperature_fan=chamber target=35.0
Signed-off-by: Martin Nowroth <madnoth@gmail.com>
The parameter to the M221 command should be the ratio of the nominal to
measured filament area, rather than the ratio of the diameters. Since we
are taking the ratio, most of the area calculation cancels out.
Fixes#1535.
Signed-off-by: Len Trigg <lenbok@gmail.com>
The servo pins (P9_14/P9_16) are muxed to the SOCs hardware PWM unit
driven by a 13MHz GP timer. They have to be driven by the linux host
mcu. This commits adds hardware PWM support using the linux sysfs
user space interface.
The servo pins can be specified as "replicape:servo0" and
"replicape:servo1". Removes the "servo0_enable", "servo1_enable"
configuration parameters.
Fixes#1105.
Signed-off-by: Janne Grunau <janne-3d@jannau.net>
Due to the corexy kinematics, the individual steppers may have a
velocity of sqrt(2) times faster than the cartesian velocity _and_ can
have an acceleration of sqrt(2) times faster. Make sure to calculate
in the higher acceleration.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Arksine
Kevin O'Connor
Artem Belevich
fess
LyleCheatham
Stephan
alfsoft
Martin Nowroth
Len Trigg
Dmitry
Trevor Jones
Daniel
Janar Sööt
Janne Grunau
Douglas Hammond