Add updates to example-extras.cfg and G-Codes.md documenting pause_resume. Also add M600 (filament change) to sample-macros.cfg.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
This module adds PAUSE and RESUME gcodes that can programatically determine if the gcode is printing from virtual sd or over the serial connection. It also captures the current toolhead position and gcode feedrate on pause, and recovers that position and feedrate on resume.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
- Add is_active() member function to return the active printing status of the virtual sdcard
- M27 now reports current file position when file has been opened. See http://marlinfw.org/docs/gcode/M027.html
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Move the definition of SERIAL_BAUD to the main src/Kconfig file. Only
show this as an option if the user selects the ability to configure
low-level options.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for performing linear interpolation between a set of
measured temperature/resistance pairs.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the low-level PrinterADCtoTemperature() class from thermistor.py
to adc_temperature.py and use it from the Linear() class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
We want the duration of each command to be an exact multiple of
SIGNAL_PERIOD. The durations might not be exact if the bltouch is on
a secondary mcu. Account for this in send_cmd().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rework the undocumented test_sensor_pin config option into a
pin_up_touch_mode_reports_triggered option and document it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Query the bltouch state during the pin_up command to try and verify
that the probe does actually retract. This may be useful to detect if
the bltouch enters into an "error" state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The BLTouch is more accurate when probing in "pin_down" mode than
"touch_mode" (at least on some hardware). Rework the code to use that
mode.
When probing in pin_down mode, the BLTouch can go into an error state
if a pin_up is not sent immediately after a touch signal. Rework the
pin_up code to reduce the time it takes to transmit the command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce a sync_print_time() method and update send_cmd() to track
the duration of bltouch commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Verify that there is always some movement during a probing operation.
This is normally done by the homing.py code (via its verify_movement
check), but that check may not be enabled when z_virtual_endstop is
used. So, always enable the check in the bltouch.py code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Separate the thermistor math from the heater temperature callback
system. This may make it easier for debugging.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The lpc176x ADC is extremely noisy. Implement a 5 order median filter
on each ADC read to weed out obviously incorrect readings.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Order the adc config code so that a shutdown from gpio_adc_setup()
doesn't result in analog_in_shutdown() running on a 'struct analog_in'
that hasn't yet been configured.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Only update the status message with the first error report.
Subsequent errors are often the result of the first error and
reporting the last error can be misleading.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Make sure to explicitly cast to 32bit integers when doing math on
16bit integers that require the extra precision as the AVR uses a
16bit int.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Make sure to not query the given endstop until after the start of the
requested operation. This ensures that the operation has started
prior to querying the status of that operation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Make sure the endstop checking is started prior to any movement. This
helps ensure the verify_movement check is accurate.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Whenever a stepper driver or a heater becomes active, it is desirable to turn on a fan cooling the associated parts on the controller board. This module implements such a fan that turns on whenever a stepper or specified heater turns on, decelerates to a configurable speed when all of the watched parts turn off, and returns to an off-speed, when a user-defined timeout is met.
Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
This is my current config file for Fysect F6 + TMC2208 running on my
Ender 3 with stock creality display.
Signed-off-by: Simone Bonacini <bonacini.simone@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Arksine
Ales Stimec
Kevin O'Connor
fredizzimo
Rui Caridade
Florian Heilmann
Víctor Martínez
Master92
AxMod3DPrint
SimoneBnc
Nathan