Don't pass pin_type to lookup_pin() - instead, if a pin can be
inverted or can have a pullup, then the caller must explicitly specify
that when calling lookup_pin(). This simplifies the code for the
cases where it is not valid to invert or pullup.
Explicitly pass the pin_type to setup_pin() and have ppins.setup_pin()
apply default pullup and invert flags.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Send the temperature before checking for an out of range error (that
makes it easier to debug).
The query_thermocouple clock parameter is unpredictable and a value of
zero can't be used to disable the query - use rest_ticks instead.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Make sure to use is_init=True when sending query_thermocouple -
otherwise, the config CRC is likely to mismatch on every connection.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Raising an error from the background message reception thread isn't
well defined. Instead, on a temperature fault, invoke a printer
shutdown.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Those chips that require an spi init sequence can generate the message
directly in the chip specific class.
Also, don't send an spi init message for chips that are read-only.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The MAX6675 chip has a different read sequence than the MAX31855 chip.
Signed-off-by: Ricardo Amézquita <ramezquitao@cihologramas.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the "motor_off_timeout" tracking to a new module in the extras/
directory. This makes it easier to customize the idle timeout
behavior.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The junction_deviation configuration parameter has a number of quirks
that make it difficult to configure. Replace it with a
"square_corner_velocity" configuration parameter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's rare to have all the Z stepper locations directly under the
printable surface, so using z_positions for points is not a good
default.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allocate the stepper_kinematics directly in mcu.py - that way the
kinematic classes don't have to interact with the chelper code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move extruder.py, cartesian.py, corexy.py, and delta.py to a new
kinematics/ sub-directory. This is intended to make adding new
kinematics a little easier.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't issue a get_config command after building the config as the
built config may contain time sensitive initialization commands.
Instead, send the config and init commands immediately after invoking
the build_config() callbacks. This avoids some rare "timer too close"
errors during configuration.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the simulator to use the generic timer_irq.c and serial_irq.c
code for (dummy) timer and io handling. This is just to make the code
a better example for other developers (most micro-controllers will use
the timer_irq.c and serial_irq.c code).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Added printer-tronxy-x8-2018.cfg for the Tronxy X8 with the CXY-V2-0508 board.
Signed-off-by: Seyed Seraj <s.seraj@hotmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Switch the host code from the CLOCK_MONOTONIC clock to the Linux
specific CLOCK_MONOTONIC_RAW clock. It's common for ntp to slew the
CLOCK_MONOTONIC clock to account for drift, and that can break the
host's ability to make accurate predictions of the micro-controller
clock. This could lead to "move queue empty" errors. The
CLOCK_MONOTONIC_RAW clock is not slewed and thus should not have this
problem.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Ricardo Amezquita
Pascal Albert
Seyed Seraj