The beagleboard TI kernel 4.14 and 4.19 contain a commit which change
the device names ("pwm: Create device class for pwm channels") from
pwmN to pwm-${chip}:N. This commit was never merged into the upstream
kernel.
Decrease the number of pwm channels to a more reasonable 16. Increase
the number of pwm chips to 8 since the replicape servo pwm outputs are
on pwmchip4.
Update replicape code to detect appropriate channel.
Signed-off-by: Janne Grunau <janne-gh@jannau.net>
Add a 50ms delay from the initial clock measurement to the first
get_clock query. Disable the prediction_variance filter on each
get_clock query so that none of those measurements are ignored.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The heater logic is an independent module that does not need to be
treated as part of the "core" klipper code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's no longer necessary to queue gcode scripts - gcode.run_script()
now does that automatically.
Also, make release_gcode config optional.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The probe_finalize() name is used for callbacks in both the
PrinterProbe and ProbePointsHelper classes. Rename the PrinterProbe
callback to avoid confusion.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename the method to make it more clear that it is a low-level call
that should be rarely used.
Also, change gcode_button.py, hall_filament_width_sensor.py, and
tsl1401cl_filament_width_sensor.py to use respond_info() instead of
respond_raw().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Report low-level disk errors via the log and use the normal sdcard
mechanism to report end of sdcard print to gcode users.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's important to raise an error (instead of calling respond_error() )
so that a G20 will stop a virtual_sdcard print.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
No need to check for '#original' in params - it's always there.
Properly handle a lower case m118 command. Don't register a help text
for the legacy M118 g-code command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Raising an error (instead of reporting an error) is important as only
a raised error will stop a print from virtual_sdcard.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 402110f6 didn't actually fix absolute extrude mode. For now,
report an error if an extrude move is requested in absolute extrude
mode.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Fix linear_travel optimization. Use "2*pi" instead of "radians(360)".
Always emit at least one segment and always end at the final target
coordinates.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Fix Z moves so that the movement is spaced out among the arc movements.
Fix extrude moves when in absolute extrude mode.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the normal gcode.get_float() mechanism for extracting parameters
from the g-code command.
Don't register descriptions for the G2/G3 commands as the convention
is to only use descriptions for "extended g-code commands".
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This reverts commit 5c8d15bbee.
The lower_probe() code was already manually optimizing the timing of
the pwm disable, and that conflicted with the optimization in commit
5c8d15bb.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Fysetc Cheetah v1.2 boards require a special sequence to reset reliably.
This sequence works for me in all cases. Simpler sequences without
double reset did not work correctly. This is likely because of a weird
stateful circuitry for toggling the bootloader state.
Cheetah boards use RTS to configure bootloader triggering. By default,
pySerial sets RTS on connect, which unfortunately configures the board
to start the bootloader on reset.
Add a toggle for the RTS state to allow users to workaround. The RTS state
is set before the serial connection is opened, so there are no glitches.
Addresses #2026.
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Some clones don't raise the pin on a reset and the ANTClabs BL-Touch
sometimes doesn't raise the pin either.
Rework the (infrequently called) sensor test code to always issue a
pin_up command before the touch command. Also, perform a reset and
retry if the sensor test fails.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Be sure to fully raise the probe prior to starting any future toolhead
movements in the multi_probe_end() case.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If an error is found during the pin_up_not_triggered check, then apply
the reset command for a full second (instead of just 100ms). This
gives the bltouch more time to check its internal state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Return the triggered state from verify_state() and update the callers
to raise the error (if needed).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some stepper motor drivers do not respond well to rapid "step +
direction change + step" events. In particular, it is believed this
can cause "over current" events on the tmc2208 drivers when they are
in "stealthchop" mode. Detect these events and remove them from the
generated step times.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It is likely only developers will be interested in testing the menu
system, so no need to have it in the default menu.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Disable support for customizing the main lcd display content via the
menu system. Advise users to use the new display_data config sections
as a replacement.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce a new config based system for specifying the on-screen
contents of an lcd screen. The default screen configuration (found in
klippy/extras/display/display.cfg) is the same as the previous
hard-coded display, so this should not change behavior for existing
users.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some stepper motor drivers do not respond well to rapid "step +
direction change + step" events. In particular, it is believed this
can cause "over current" events on the tmc2208 drivers when they are
in "stealthchop" mode. Detect these events and remove them from the
generated step times.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the stepper changes direction then the average velocity since the
last step pulse isn't a good indicator of the next step pulse.
Instead, reset the bounds checking to use a low starting guess.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The queue_append system predates the iterative solver - it was useful
when many different kinematic functions directly added steps to the
step compression queues. With the iterative solver being the only
source of step generation, it is simpler to directly add steps from
the iterative solver code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use new mcu.lookup_query_command() for all commands that query
information from the micro-controller.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Convert standard queries to use the acknowledgments of the sent
command to determine if the response was received or not. This also
controls command retransmissions (should the response have been lost).
The tmc_uart.py will continue to use the old mechanism as the tmcuart
responses are not sent synchronously with the query command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add ability for the host code to get a notification when the ack for a
command sent to the micro-controller is received. This is in
preparation for improved detection of message loss between mcu and
host.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's not valid to set the TPWMTHRS in a "klippy:connect" event handler
because the TMCVirtualPinHelper and TMCCommandHelper classes were
expecting that field to be set during the config reading phase.
Revert "tmc: Fix typo preventing stealthchop threshold from being set"
This reverts commit 7d76067ff9.
Revert "tmc: Query the stepper step_distance from the stepper object"
This reverts commit 67b2852249.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change home_wait() to return if the homing operation completed
succesfully or not. This simplifies the callers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update the endstop code to return its trigger completion object during
home_start(). Update the toolhead class to take a completion object
(instead of creating its own). This reduces the number of
intermediate callbacks needed during a homing operation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's simpler to query the "printing" status from the idle_timeout
module on an event than it is to track changes to the printing status.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce min_event_systime and rework the previous start_time,
last_event_time, and event_running flags into this one state tracking
variable.
This also makes a minor change to the behavior of the event_delay - it
is now calculated from the time the command completes execution
(instead of from when the event is first detected). This may make a
difference if there is a long running g-code command occurring during
the detection event.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rather than inherit from the BaseSensor, filament sensor implementatons
may instantiate the RunoutHelper and update the filament state via its
note_filament_present method.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Add support for notifying the low-level probing handlers that a
multiple probe sequence is occurring. This is in preparation for the
bltouch code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Collapse the "homing:move_begin", "homing:move_end", home_prepare(),
and home_finalize() into two new events: "homing:homing_move_begin"
and "homing:homing_move_end". This simplifies the homing code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When overriding a g-code command, allow the caller to obtain the
previous command handler. Use this feature in homing_override and
safe_z_home.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't obtain the step_distance from the config, instead obtain
step_distance from the instantiated stepper object.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't obtain the step_distance from the config, instead obtain
step_distance from the instantiated stepper object.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
In the rare case where the step generation code finds an interval of
zero, it was possible for an integer division of a negative number to
cause an incorrect result. Fix that by using the idiv_up() and
idiv_down() helpers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
There have been several reports that increasing the delay from 37us to
40us eliminates screen corruption on some clone hd44780 displays.
Increase the timeout value so that the standard code works on these
displays.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The caller can now determine which steppers are connected to cartesian
Z movement via the new stepper.is_active_axis() method. It is
therefore no longer necessary for the kinematic code to identify these
steppers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move interpolation checks to _init_mesh_params() so they can be done whle the config is being parsed. Do not allow a probe_count higher than 6 for lagrange interpolation, as this typically leads to oscillation.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Don't force probing when BED_MESH_MAP is executed, output the existing mesh. If the user wants to probe each time before a map they can do so with a gcode_macro.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Renamed some variables in set_mesh() previous called "mesh_min" and "mesh_max" to alleviate confusion with the config options.
Renamed several attributes for clarity. The "calibrate" attribute is now bmc, "probe_params" is now "mesh_params", "probed_z_table" is now "probed_matrix", "mesh_z_table" is now "mesh_matrix".
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Points are now logged after the printer is ready. The formatting is improved, printing out the point index, and its corresponding automatic and manual points.
BED_MESH_OUTPUT now includes a PGP parameter, if PGP=1 the generated points are printed to the terminal.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Rename min_point, max_point, and bed_radius to mesh_min, mesh_max, and mesh_radius respectively. Add "mesh_origin" option, that allows round beds to specificy the center of the mesh.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Fix typo that resulted in _get_extended_params() being called for all
commands. Allow "extended" g-code commands to contain numbers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some kinematics do not result in a constant step rate during homing
operations. Calculate the endstop checking rate using the total
distance traveled on the axis divided by the axis step distance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The STEPPER_BUZZ command needs to know if the axis is using radians
instead of millimeters so that it can move a more appropriate
distance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a mechanism for obtaining the print_time via a callback instead of
by flushing the look-ahead queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The print_time parameter of heater.set_temp() is not currently used
and it isn't necessary to flush the look-ahead queue just get the
print_time. Remove the parameter from heater.set_temp() to avoid
flushing the look-ahead queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If a null move is added as the first move on the trapezoid motion
queue then it could have a very large move->move_t value. This could
cause numerical stability issues with some advanced kinematic
formulas. Place a limit on the move_t value to avoid this.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This reverts commit 1b92af6078.
The standard "uc1701" lcd_type can now be used in place of the custom
"st7567" lcd_type.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the queuelogger was holding the lock when the process is forked
then any attempt to log from the background process would result in a
deadlock. Attempt a workaround by disabling the queuelogger at the
start of the background process.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Provide a list of available heater and sensor names to
gcode macro templates through the printer.heater.available_heaters
and printer.heater.available_sensors variables
Signed-off-by: Simon Kühling <mail@simonkuehling.de>
The builtin Tn command is not sufficiently flexible to control some
multi-extruder printers. Remove the command and encourage users to
define individual gcode_macros for each Tn instance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The M206 command isn't particularly standardized and isn't issued by
default from 3rd party software in their standard configurations.
Encourage users to use the more powerful SET_GCODE_OFFSET command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implement the pressure advance calculations while performing the
definitive integral calculations. This simplifies both the
extruder.py and kin_extruder.c code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The probe object may not have be instantiated when the
screws_tilt_adjust object is instantiated. Just remove the check.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The S parameter is not a standard and was not commonly used. The P
parameter (delay specified in milliseconds) is the commonly accepted
g-code mechanism for dwelling.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for an optional uc1701 rst_pin. Use the same reset pin
code handling with the SSD1306 code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
There is concern that some lcd boards that emulate the hd44780 don't
support text updates that wrap the two text framebuffers. Update the
code to treat the two text areas as two separate framebuffers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Large increases in fan speed can suffer from acceleration lag, so this
change kick starts the fan for a change of 50% or more in the same way
that starting the fan from 0% does.
Signed-off-by: Justin Schuh <code@justinschuh.com>
If an M25 is in a gcode file that is being printed from virtual SD, it
would cause a permanent hang. Detect that case and don't wait for
those M25 commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the extruder lookahead method is no longer used it can be
removed from the toolhead and extruder classes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support averaging the extruder position over a time range to "smooth
out" the velocity changes that occur during pressure advance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support calculating the definitive integral of a cartesian axis
position over a time range of the movement queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for kinematic functions that calculate step times based on
a range of the motion queue. This requires adding additional pause
times when fully flushing the motion queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for generating steps from kinematic functions that
calculate step times based on a range of the motion queue. It
requires scanning for step generation during the lead up to stepper
activity (when the stepper would nominally be idle). And it requires
scanning for step generation just after a stepper has nominally become
idle.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use sentinels to make list traversal code simpler. Also add in null
moves so that there are no time gaps in the list.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update code that modifies the low-level kinematics handlers to first
call toolhead.flush_step_generation().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't transition to the normal movement state if there aren't any
moves actually ready to be processed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the only caller to set_commanded_position() is
set_position(), remove the set_commanded_position() method and pass
the set_position() call directly to the itersolve.c code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the homing code does not call set_commanded_position(), it is
no longer necessary to save/restore the position in the bltouch code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the homing code does not use get_commanded_position(), it is
no longer necessary to alter the low-level commanded position after a
homing move.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename calc_position() to calc_tag_position() and have it calculate
the value of the position from the last stepper set_tag_position()
call. This enables the calc_tag_position() code to be more flexible
as it can be run with arbitrary positions.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Lucio Tarantino
Janne Grunau
Kevin O'Connor
Piotr Usewicz
Grigori Goronzy
David Smith
Jeremy Briffaut
kakou-fr
Arksine
Denis Ignatenko
FanDjango
Christian S
FanDjango
Simo Apell
Daniel Kucera
Simon Kühling
Petri Honkala
Matt Baker
Justin Schuh
Florian Heilmann