When enabling "low level options" in Kconfig, selecting a chip that is
20Mhz capable would result in 20Mhz being the default. A 16Mhz speed
is the preferred default, so list that first in the menu.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The FIOSET and FIOCLR registers may not set an initial value if the
pin is not in an output mode. So, use FIOPIN to set the initial
value.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When reducing the maximum speed due to the max_accel_to_decel setting,
move velocity limits must still be propagated. Otherwise, the
trapezoid move planner may produce moves with velocity jumps.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Since the previous config file was laid out only for TMC2208 drivers and was missing most other pins, I made a comprehensive configuration file, with hardware names for all available functionality.
Signed-off-by: Tobias Weiß <t.weiss@bk.ru>
Once a hop is performed, it will only be re-issued if the z-axis has been
moved in the meantime. Usually it is only moved by a z-homing so doing so
will cause safe_z_home to do the hop on the next homing action.
When z-axis is homed, x and y positions are known. When setting this
boolean option, these are set back to their last positions.
Whenever a hop is specified it is re-issued after the Z axis has been
homed. This is especially necessary when a pressure-based probe is used.
Also, the module decides if a hop is necessary, based on either a known
Z position or a flag that is set whenever the motors are disabled.
Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
Previously, when a sercom pin specified the mcu (myname:PIN), it would result in a pin enumeration error.
Signed-off-by: John Jardine <john@gprime.net>
The usbfs receive buffers must also have space for the 2 byte crc at
the end of a transmission. This fixes an error that could lead to
lost messages from mcu to host (resulting in bytes_invalid increasing
in stats) on the stm32f103.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
As per 18e6772010
This lowers the voltage and thus brings the stepper motor temperature to
an acceptable level. Beforehand, motors would get very hot.
Signed-off-by: Piotr Usewicz <piotr@layer22.com>
The SKR mini E3 is marketed as being for the Ender 3, so it makes
sense for the example electronics config to be more similar to the
Ender 3 config.
Reported by @TheDogee.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
R Still missing, also might be somewhat dirty since code is converted
into G1 commands.
Signed-off-by: Aleksej Vasiljkovic <achmed21@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It appears the usbotg controller can get confused if the usb irq
handler runs while processing a usb request. Disable usb irqs during
usb processing to avoid this.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the XFRC interrupt instead of TXFE. Don't mask/unmask the tx
interrupts during runtime. This fixes some race conditions where a tx
notification may have previously gotten lost.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the lpc176x code uses the armcm_boot mechanism, it is no
longer necessary for SystemInit to be externally visible.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the stm32f1 code uses the armcm_boot mechanism, it is no
longer necessary for SystemInit to be externally visible.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Julien Lirochon
Petri Honkala
Piotr Usewicz
achmed20
towe96
Master92
John Jardine
Arksine