Provide a list of available heater and sensor names to
gcode macro templates through the printer.heater.available_heaters
and printer.heater.available_sensors variables
Signed-off-by: Simon Kühling <mail@simonkuehling.de>
The builtin Tn command is not sufficiently flexible to control some
multi-extruder printers. Remove the command and encourage users to
define individual gcode_macros for each Tn instance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The M206 command isn't particularly standardized and isn't issued by
default from 3rd party software in their standard configurations.
Encourage users to use the more powerful SET_GCODE_OFFSET command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implement the pressure advance calculations while performing the
definitive integral calculations. This simplifies both the
extruder.py and kin_extruder.c code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The probe object may not have be instantiated when the
screws_tilt_adjust object is instantiated. Just remove the check.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The S parameter is not a standard and was not commonly used. The P
parameter (delay specified in milliseconds) is the commonly accepted
g-code mechanism for dwelling.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for an optional uc1701 rst_pin. Use the same reset pin
code handling with the SSD1306 code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
There is concern that some lcd boards that emulate the hd44780 don't
support text updates that wrap the two text framebuffers. Update the
code to treat the two text areas as two separate framebuffers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Large increases in fan speed can suffer from acceleration lag, so this
change kick starts the fan for a change of 50% or more in the same way
that starting the fan from 0% does.
Signed-off-by: Justin Schuh <code@justinschuh.com>
If an M25 is in a gcode file that is being printed from virtual SD, it
would cause a permanent hang. Detect that case and don't wait for
those M25 commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the extruder lookahead method is no longer used it can be
removed from the toolhead and extruder classes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support averaging the extruder position over a time range to "smooth
out" the velocity changes that occur during pressure advance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support calculating the definitive integral of a cartesian axis
position over a time range of the movement queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for kinematic functions that calculate step times based on
a range of the motion queue. This requires adding additional pause
times when fully flushing the motion queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for generating steps from kinematic functions that
calculate step times based on a range of the motion queue. It
requires scanning for step generation during the lead up to stepper
activity (when the stepper would nominally be idle). And it requires
scanning for step generation just after a stepper has nominally become
idle.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use sentinels to make list traversal code simpler. Also add in null
moves so that there are no time gaps in the list.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update code that modifies the low-level kinematics handlers to first
call toolhead.flush_step_generation().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't transition to the normal movement state if there aren't any
moves actually ready to be processed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the only caller to set_commanded_position() is
set_position(), remove the set_commanded_position() method and pass
the set_position() call directly to the itersolve.c code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the homing code does not call set_commanded_position(), it is
no longer necessary to save/restore the position in the bltouch code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the homing code does not use get_commanded_position(), it is
no longer necessary to alter the low-level commanded position after a
homing move.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename calc_position() to calc_tag_position() and have it calculate
the value of the position from the last stepper set_tag_position()
call. This enables the calc_tag_position() code to be more flexible
as it can be run with arbitrary positions.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the tmc drivers perform automatic soft stepper enabling,
there is no need to be able to list multiple pins in the enable_pin
config setting.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Automatically detect if the stepper has a dedicated enable line. If
it does not, then automatically enable virtual enable support.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the PrinterStepper and MCU_stepper classes have been merged,
there is no need for the add_to_endstop() method.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the enable line tracking out of the main stepper.py code. This
simplifies the main kinematic code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Directly disable all the stepper motors on a global motor_off() from
the StepperEnable() class in stepper_enable.py. This simplifies the
toolhead and kinematic classes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Minor rework of the loop to reduce the chance that numerical stability
could cause an infinite loop.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
No longer allow the primary extruder to be named "extruder0". This
avoids internal and external confusion between the printer objects and
config section names.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Do not apply max_extrude_cross_section check, and do apply
extrude_only_xxx checks to Z only moves that also extrude. Some
printer start scripts will prime the extruder while moving the Z.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Calculate the ratio of axis distance to total move distance (axis_d /
move_d) and store in a new member variable axes_r. This avoids
needing to recalculate the value in other code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Only track a single acceleration movement in a 'struct move' instance.
Break the classic trapezoid movement (accel, cruise, decel) into three
separate movements. This simplifies the calculation logic.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Load all items from the look-ahead queue into the trapezoid velocity
queue, and then flush that queue by time. This prevents the host cpu
from being starved on very long moves (which may require a large
number of steps to be generated). It also improves the overall
performance.
With the batch flushing logic in place, it is no longer necessary to
split homing moves up.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that all callers use the trapq system to queue moves, it is no
longer necessary to individually allocate and fill a 'struct move'.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Eliminate the old gen_steps() call now that all callers have been
converted to the newer trapq based generate_steps().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that all kinematics use the trapq system, there is no need to call
into the kinematics on each g-code move.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support associating a stepper_kinematics with a trapq. Support
generating steps from a time range on the given trapq.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for building a list of moves in the trapq.c code. Update
the toolhead code so that moves generated from the look-ahead code are
added to that list.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the kinematic position calculation function had an error in it (if
it produces sudden position changes) then it could lead to an infinite
loop in itersolve_gen_steps().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Break up the connect phase into two phases - mcu_identify and connect.
The first phase will contact all the micro-controllers and obtain the
"identify" data dictionaries for them. Once all the micro-controllers
have been contacted, then they can be configured. This fixes an issue
with FIRMWARE_RESTART not working correctly on multi-mcu setups that
use restart_method=command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Wait in the M25 command handler until the work_handler() background
timer fully exits. This ensures that subsequent g-code commands (such
as M27 or M24) will correctly report a paused state.
Reported by @foosel.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The initial clock measurement wasn't properly implementing a small
delay between clock queries. Fix the pause() call so there is a small
delay between queries.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some print start scripts may extrude at a position slightly higher
than the first z layer height. Tweak the backwards z test to reduce
the chance of the tuning test ending prematurely.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
PR #1970 introduced a new parameter, controlling the default behavior of the safe_z_home-module. To avoid unexpected changes, the default of the move_to_previous is now defaulted to False.
Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
If '[stepper_x]' and/or '[stepper_y]' have a 'position_min' that is
non-zero, and '[safe_z_home] home_xy_position' is '0,0'; then the 'G28'
command will _not_ move to '0,0'; but stay at 'position_min' during the
Z endstop test.
This fix corrects this issue.
Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
Below off_below the fan will be turned off. When configured correctly this
can prevent stalling, which may lead to overheating and failed fans. To
simplify calibration and use of this setting, off_below is applied in the
input duty cycle domain, prior to any scaling due to e.g. max_power.
Signed-off-by: Nicholas Seckar <nseckar@gmail.com>
When reducing the maximum speed due to the max_accel_to_decel setting,
move velocity limits must still be propagated. Otherwise, the
trapezoid move planner may produce moves with velocity jumps.
Signed-off-by: Dmitry Butyugin <dmbutyugin@google.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Once a hop is performed, it will only be re-issued if the z-axis has been
moved in the meantime. Usually it is only moved by a z-homing so doing so
will cause safe_z_home to do the hop on the next homing action.
When z-axis is homed, x and y positions are known. When setting this
boolean option, these are set back to their last positions.
Whenever a hop is specified it is re-issued after the Z axis has been
homed. This is especially necessary when a pressure-based probe is used.
Also, the module decides if a hop is necessary, based on either a known
Z position or a flag that is set whenever the motors are disabled.
Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
Previously, when a sercom pin specified the mcu (myname:PIN), it would result in a pin enumeration error.
Signed-off-by: John Jardine <john@gprime.net>
R Still missing, also might be somewhat dirty since code is converted
into G1 commands.
Signed-off-by: Aleksej Vasiljkovic <achmed21@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
During a "drip feed" move, both the move's maximum speed and maximum
acceleration may be limited by the kinematics.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a helper class for tracking gpio outputs that are synchronized to
bus updates on a particular command queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rework the spi_config commands so that bus configuration and shutdown
message configuration is done separately from the main "config_spi"
command. This makes the spi configuration more flexible. It's now
possible to use software spi without a CS pin. It's now possible to
define multiple SPI messages to send on a shutdown event.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
use SET_GCODE_OFFSET's MOVE=1 parameter in the z offset menu.
Less confusing for people who think nothing happened.
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
Kevin O'Connor
Simon Kühling
Petri Honkala
Matt Baker
Justin Schuh
Florian Heilmann
Arksine
Geoff Shannon
Master92
Jason S. McMullan
Nicholas Seckar
Julien Lirochon
Piotr Usewicz
achmed20
John Jardine
fess