config: Remove hold_current from sample configs and sample macros

Now that the documentation recommends that hold_current not be set,
update the example config files to not specify a hold_current.

Signed-off-by: Kevin O'Connor <kevin@koconnor.net>

config/generic-bigtreetech-e3-rrf-v1.1.cfg

@@ -23,7 +23,6 @@ homing_speed: 50
 [tmc2209 stepper_x]
 uart_pin: PD6
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_y]
@@ -40,7 +39,6 @@ homing_speed: 50
 [tmc2209 stepper_y]
 uart_pin: PD1
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_z]
@@ -56,7 +54,6 @@ position_max: 250
 [tmc2209 stepper_z]
 uart_pin: PD15
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [extruder]
@@ -80,7 +77,6 @@ max_temp: 250
 [tmc2209 extruder]
 uart_pin: PD11
 run_current: 0.650
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [heater_bed]

config/generic-bigtreetech-gtr.cfg

@@ -126,37 +126,31 @@ max_z_accel: 5
 #[tmc2208 stepper_x]
 #uart_pin: PC14
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_y]
 #uart_pin: PE1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_z]
 #uart_pin: PB5
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder]
 #uart_pin: PG10
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder1]
 #uart_pin: PD4
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder2]
 #uart_pin: PC12
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 
@@ -167,7 +161,6 @@ max_z_accel: 5
 #[tmc2130 stepper_x]
 #cs_pin: PC14
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
 #spi_software_miso_pin: PB6
@@ -177,7 +170,6 @@ max_z_accel: 5
 #cs_pin: PE1
 #sense_resistor: 0.075
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
 #spi_software_miso_pin: PB6
@@ -187,7 +179,6 @@ max_z_accel: 5
 #cs_pin: PB5
 #sense_resistor: 0.075
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
 #spi_software_miso_pin: PB6
@@ -197,7 +188,6 @@ max_z_accel: 5
 #cs_pin: PG10
 #sense_resistor: 0.075
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
 #spi_software_miso_pin: PB6
@@ -207,7 +197,6 @@ max_z_accel: 5
 #cs_pin: PD4
 #sense_resistor: 0.075
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
 #spi_software_miso_pin: PB6
@@ -217,7 +206,6 @@ max_z_accel: 5
 #cs_pin: PC12
 #sense_resistor: 0.075
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
 #spi_software_miso_pin: PB6
@@ -232,7 +220,6 @@ max_z_accel: 5
 #sense_resistor: 0.075
 #interpolate: True
 #run_current: 1
-#hold_current: 1
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
 #spi_software_miso_pin: PB6
@@ -243,7 +230,6 @@ max_z_accel: 5
 #sense_resistor: 0.075
 #interpolate: True
 #run_current: 1
-#hold_current: 1
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
 #spi_software_miso_pin: PB6
@@ -254,7 +240,6 @@ max_z_accel: 5
 #sense_resistor: 0.075
 #interpolate: True
 #run_current: 0.4
-#hold_current: 0.4
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
 #spi_software_miso_pin: PB6
@@ -265,7 +250,6 @@ max_z_accel: 5
 #sense_resistor: 0.075
 #interpolate: True
 #run_current: 0.5
-#hold_current: 0.5
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
 #spi_software_miso_pin: PB6
@@ -276,7 +260,6 @@ max_z_accel: 5
 #sense_resistor: 0.075
 #interpolate: True
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
 #spi_software_miso_pin: PB6
@@ -287,7 +270,6 @@ max_z_accel: 5
 #sense_resistor: 0.075
 #interpolate: True
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 0
 #spi_software_mosi_pin: PG15
 #spi_software_miso_pin: PB6

config/generic-bigtreetech-octopus.cfg

@@ -153,52 +153,44 @@ max_z_accel: 100
 #uart_pin: PC4
 ##diag_pin: PG6
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2209 stepper_y]
 #uart_pin: PD11
 ##diag_pin: PG9
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2209 stepper_z]
 #uart_pin: PC6
 ##diag_pin: PG10
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 
 #[tmc2209 stepper_]
 #uart_pin: PC7
 ##diag_pin: PG11
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 
 #[tmc2209 extruder]
 #uart_pin: PF2
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2209 extruder1]
 #uart_pin: PE4
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2209 extruder2]
 #uart_pin: PE1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2209 extruder3]
 #uart_pin: PD3
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 ########################################
@@ -210,7 +202,6 @@ max_z_accel: 100
 #spi_bus: spi1
 ##diag1_pin: PG6
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_y]
@@ -218,7 +209,6 @@ max_z_accel: 100
 #spi_bus: spi1
 ##diag1_pin: PG9
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_z]
@@ -226,7 +216,6 @@ max_z_accel: 100
 #spi_bus: spi1
 ##diag1_pin: PG10
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_]
@@ -234,35 +223,30 @@ max_z_accel: 100
 #spi_bus: spi1
 ##diag1_pin: PG11
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder]
 #cs_pin: PF2
 #spi_bus: spi1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder1]
 #cs_pin: PE4
 #spi_bus: spi1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder2]
 #cs_pin: PE1
 #spi_bus: spi1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder3]
 #cs_pin: PD3
 #spi_bus: spi1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 [board_pins]

config/generic-bigtreetech-skr-2.cfg

@@ -132,19 +132,16 @@ aliases:
 #[tmc2209 stepper_x]
 #uart_pin: PE0
 #run_current: 0.800
-#hold_current: 0.800
 #diag_pin:
 
 #[tmc2209 stepper_y]
 #uart_pin: PD3
 #run_current: 0.800
-#hold_current: 0.800
 #diag_pin:
 
 #[tmc2209 stepper_z]
 #uart_pin: PD0
 #run_current: 0.800
-#hold_current: 0.800
 #diag_pin:
 
 #[tmc2209 extruder]

config/generic-bigtreetech-skr-cr6-v1.0.cfg

@@ -27,7 +27,6 @@ homing_speed: 50
 uart_pin: PC11
 tx_pin: PC10
 run_current: 0.550
-hold_current: 0.450
 stealthchop_threshold: 999999
 uart_address: 0
 
@@ -48,7 +47,6 @@ uart_pin: PC11
 tx_pin: PC10
 uart_address: 2
 run_current: 0.550
-hold_current: 0.450
 stealthchop_threshold: 999999
 
 [stepper_z]
@@ -67,7 +65,6 @@ uart_pin: PC11
 tx_pin: PC10
 uart_address: 1
 run_current: 0.550
-hold_current: 0.450
 stealthchop_threshold: 999999
 
 [extruder]
@@ -93,7 +90,6 @@ uart_pin: PC11
 tx_pin: PC10
 uart_address: 3
 run_current: 0.600
-hold_current: 0.400
 stealthchop_threshold: 999999
 
 [heater_bed]

config/generic-bigtreetech-skr-e3-dip.cfg

@@ -99,25 +99,21 @@ pins: !PC13
 #[tmc2208 stepper_x]
 #uart_pin: PC10
 #run_current: 0.580
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_y]
 #uart_pin: PC11
 #run_current: 0.580
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_z]
 #uart_pin: PC12
 #run_current: 0.580
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder]
 #uart_pin: PD2
 #run_current: 0.650
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 
@@ -129,28 +125,24 @@ pins: !PC13
 #cs_pin: PC10
 #spi_bus: spi3
 #run_current: 0.580
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_y]
 #cs_pin: PC11
 #spi_bus: spi3
 #run_current: 0.580
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_z]
 #cs_pin: PC12
 #spi_bus: spi3
 #run_current: 0.580
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder]
 #cs_pin: PD2
 #spi_bus: spi3
 #run_current: 0.650
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 

config/generic-bigtreetech-skr-e3-turbo.cfg

@@ -19,7 +19,6 @@ homing_speed: 50
 uart_pin: P1.1
 #diag_pin: P1.29
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_y]
@@ -37,7 +36,6 @@ homing_speed: 50
 uart_pin: P1.10
 #diag_pin: P1.28
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_z]
@@ -54,7 +52,6 @@ position_max: 250
 uart_pin: P1.17
 #diag_pin: P1.27
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [extruder]
@@ -79,7 +76,6 @@ max_temp: 250
 uart_pin: P0.5
 #diag_pin: P1.26
 run_current: 0.650
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 #[extruder1]

config/generic-bigtreetech-skr-mini-e3-v1.0.cfg

@@ -30,7 +30,6 @@ uart_pin: PC11
 tx_pin: PC10
 uart_address: 0
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_y]
@@ -49,7 +48,6 @@ uart_pin: PC11
 tx_pin: PC10
 uart_address: 2
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_z]
@@ -67,7 +65,6 @@ uart_pin: PC11
 tx_pin: PC10
 uart_address: 1
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [extruder]
@@ -93,7 +90,6 @@ uart_pin: PC11
 tx_pin: PC10
 uart_address: 3
 run_current: 0.650
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [heater_bed]

config/generic-bigtreetech-skr-mini-e3-v1.2.cfg

@@ -28,7 +28,6 @@ homing_speed: 50
 [tmc2209 stepper_x]
 uart_pin: PB15
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_y]
@@ -45,7 +44,6 @@ homing_speed: 50
 [tmc2209 stepper_y]
 uart_pin: PC6
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_z]
@@ -61,7 +59,6 @@ position_max: 250
 [tmc2209 stepper_z]
 uart_pin: PC10
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [extruder]
@@ -85,7 +82,6 @@ max_temp: 250
 [tmc2209 extruder]
 uart_pin: PC11
 run_current: 0.650
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [heater_bed]

config/generic-bigtreetech-skr-mini-e3-v2.0.cfg

@@ -27,7 +27,6 @@ uart_pin: PC11
 tx_pin: PC10
 uart_address: 0
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_y]
@@ -46,7 +45,6 @@ uart_pin: PC11
 tx_pin: PC10
 uart_address: 2
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_z]
@@ -64,7 +62,6 @@ uart_pin: PC11
 tx_pin: PC10
 uart_address: 1
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [extruder]
@@ -90,7 +87,6 @@ uart_pin: PC11
 tx_pin: PC10
 uart_address: 3
 run_current: 0.650
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [heater_bed]

config/generic-bigtreetech-skr-mini-mz.cfg

@@ -30,7 +30,6 @@ uart_pin: PC11
 tx_pin: PC10
 uart_address: 0
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_y]
@@ -49,7 +48,6 @@ uart_pin: PC11
 tx_pin: PC10
 uart_address: 1
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_z]
@@ -67,7 +65,6 @@ uart_pin: PC11
 tx_pin: PC10
 uart_address: 2
 run_current: 0.580
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [extruder]
@@ -93,7 +90,6 @@ uart_pin: PC11
 tx_pin: PC10
 uart_address: 3
 run_current: 0.650
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [heater_bed]

config/generic-bigtreetech-skr-pro.cfg

@@ -110,37 +110,31 @@ max_z_accel: 100
 #[tmc2208 stepper_x]
 #uart_pin: PC13
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_y]
 #uart_pin: PE3
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_z]
 #uart_pin: PE1
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder]
 #uart_pin: PD4
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder1]
 #uart_pin: PD1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder2]
 #uart_pin: PD6
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 
@@ -153,7 +147,6 @@ max_z_accel: 100
 #spi_bus: spi3a
 ##diag1_pin: PB10
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_y]
@@ -161,7 +154,6 @@ max_z_accel: 100
 #spi_bus: spi3a
 ##diag1_pin: PE12
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_z]
@@ -169,7 +161,6 @@ max_z_accel: 100
 #spi_bus: spi3a
 ##diag1_pin: PG8
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder]
@@ -177,7 +168,6 @@ max_z_accel: 100
 #spi_bus: spi3a
 ##diag1_pin: PE15
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder1]
@@ -185,7 +175,6 @@ max_z_accel: 100
 #spi_bus: spi3a
 ##diag1_pin: PE10
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder2]
@@ -193,7 +182,6 @@ max_z_accel: 100
 #spi_bus: spi3a
 ##diag1_pin: PG5
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 

config/generic-bigtreetech-skr-v1.3.cfg

@@ -95,31 +95,26 @@ max_z_accel: 100
 #[tmc2208 stepper_x]
 #uart_pin: P1.17
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_y]
 #uart_pin: P1.15
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_z]
 #uart_pin: P1.10
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder]
 #uart_pin: P1.8
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder1]
 #uart_pin: P1.1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 
@@ -138,7 +133,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: P0.4
 ##diag1_pin: P1.29
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_y]
@@ -148,7 +142,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: P0.4
 ##diag1_pin: P1.27
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_z]
@@ -158,7 +151,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: P0.4
 ##diag1_pin: P1.25
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder]
@@ -168,7 +160,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: P0.4
 ##diag1_pin: P1.28
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder1]
@@ -178,7 +169,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: P0.4
 ##diag1_pin: P1.26
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 

config/generic-bigtreetech-skr-v1.4.cfg

@@ -94,31 +94,26 @@ max_z_accel: 100
 #[tmc2208 stepper_x]
 #uart_pin: P1.10
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 #
 #[tmc2208 stepper_y]
 #uart_pin: P1.9
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 #
 #[tmc2208 stepper_z]
 #uart_pin: P1.8
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 #
 #[tmc2208 extruder]
 #uart_pin: P1.4
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 #
 #[tmc2208 extruder1]
 #uart_pin: P1.1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 
@@ -132,7 +127,6 @@ max_z_accel: 100
 #spi_software_mosi_pin: P1.17
 #spi_software_sclk_pin: P0.4
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 #diag1_pin: P1.29
 
@@ -142,7 +136,6 @@ max_z_accel: 100
 #spi_software_mosi_pin: P1.17
 #spi_software_sclk_pin: P0.4
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 #diag1_pin: P1.28
 
@@ -152,7 +145,6 @@ max_z_accel: 100
 #spi_software_mosi_pin: P1.17
 #spi_software_sclk_pin: P0.4
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 #diag1_pin: P1.27
 
@@ -162,7 +154,6 @@ max_z_accel: 100
 #spi_software_mosi_pin: P1.17
 #spi_software_sclk_pin: P0.4
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 #diag1_pin: P1.26
 
@@ -172,7 +163,6 @@ max_z_accel: 100
 #spi_software_mosi_pin: P1.17
 #spi_software_sclk_pin: P0.4
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 #diag1_pin: P1.25
 

config/generic-flyboard.cfg

@@ -144,55 +144,46 @@ max_z_accel: 100
 #[tmc2208 stepper_x]
 #uart_pin: PG13
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_y]
 #uart_pin: PG10
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_z]
 #uart_pin: PD5
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder]
 #uart_pin: PD1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder1]
 #uart_pin: PA14
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder2]
 #uart_pin: PG6
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder3]
 #uart_pin: PG3
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder4]
 #uart_pin: PD10
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder5]
 #uart_pin: PB12
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 
@@ -204,63 +195,54 @@ max_z_accel: 100
 #cs_pin: PG13
 ##diag1_pin: PC3
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_y]
 #cs_pin: PG10
 ##diag1_pin: PF2
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_z]
 #cs_pin: PBD5
 ##diag1_pin: PF0
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder]
 #cs_pin: PD1
 ##diag1_pin: PE15
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder1]
 #cs_pin: PA14
 ##diag1_pin: PE10
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder2]
 #cs_pin: PG6
 ##diag1_pin: PC15
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder3]
 #cs_pin: PG3
 ##diag1_pin: PC15
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder4]
 #cs_pin: PD10
 ##diag1_pin: PC15
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder5]
 #cs_pin: PB12
 ##diag1_pin: PC15
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 

config/generic-fysetc-cheetah-v1.1.cfg

@@ -25,7 +25,6 @@ uart_pin: PA3
 tx_pin: PA2
 uart_address: 0
 run_current: 0.800
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_y]
@@ -44,7 +43,6 @@ uart_pin: PA3
 tx_pin: PA2
 uart_address: 2
 run_current: 0.800
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_z]
@@ -62,7 +60,6 @@ uart_pin: PA3
 tx_pin: PA2
 uart_address: 1
 run_current: 0.800
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [extruder]
@@ -88,7 +85,6 @@ uart_pin: PA3
 tx_pin: PA2
 uart_address: 3
 run_current: 1.0
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [heater_bed]

config/generic-fysetc-cheetah-v1.2.cfg

@@ -24,7 +24,6 @@ homing_speed: 50
 uart_pin: PA12
 tx_pin: PA11
 run_current: 0.800
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_y]
@@ -42,7 +41,6 @@ homing_speed: 50
 uart_pin: PB7
 tx_pin: PB6
 run_current: 0.800
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_z]
@@ -59,7 +57,6 @@ position_max: 200
 uart_pin: PB11
 tx_pin: PB10
 run_current: 0.800
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [extruder]
@@ -84,7 +81,6 @@ max_temp: 250
 uart_pin: PA3
 tx_pin: PA2
 run_current: 1.0
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [heater_bed]

config/generic-fysetc-f6.cfg

@@ -112,42 +112,36 @@ pins: PB0
 #uart_pin: PG3
 #tx_pin: PJ2
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_y]
 #uart_pin: PJ3
 #tx_pin: PJ4
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_z]
 #uart_pin: PE2
 #tx_pin: PE6
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder]
 #uart_pin: PJ5
 #tx_pin: PJ6
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder1]
 #uart_pin: PE7
 #tx_pin: PD4
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder2]
 #uart_pin: PA1
 #tx_pin: PD5
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 ########################################
@@ -166,42 +160,36 @@ pins: PB0
 #cs_pin: PG4
 #diag1_pin: PK1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_y]
 #cs_pin: PG2
 #diag1_pin: PJ1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_z]
 #cs_pin: PJ7
 #diag1_pin: PB6
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder]
 #cs_pin: PL2
 #diag1_pin: PE4
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder1]
 #cs_pin: PC5
 #diag1_pin: PJ0
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder2]
 #cs_pin: PL7
 #diag1_pin: PK2
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 ########################################

config/generic-fysetc-s6-v2.cfg

@@ -106,37 +106,31 @@ max_z_accel: 100
 #[tmc2208 stepper_x]
 #uart_pin: PE8
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_y]
 #uart_pin: PC4
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_z]
 #uart_pin: PD12
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder]
 #uart_pin: PA15
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder1]
 #uart_pin: PC5
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder2]
 #uart_pin: PE0
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 
@@ -149,7 +143,6 @@ max_z_accel: 100
 #cs_pin: PE7
 #diag1_pin: PB14
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_y]
@@ -157,7 +150,6 @@ max_z_accel: 100
 #cs_pin: PE15
 #diag1_pin: PB13
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_z]
@@ -165,7 +157,6 @@ max_z_accel: 100
 #cs_pin: PD10
 #diag1_pin: PA0
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder]
@@ -173,7 +164,6 @@ max_z_accel: 100
 #cs_pin: PD7
 #diag1_pin: PA3
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder1]
@@ -181,7 +171,6 @@ max_z_accel: 100
 #cs_pin: PC14
 #diag1_pin: PA2
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder2]
@@ -189,7 +178,6 @@ max_z_accel: 100
 #cs_pin: PC15
 #diag1_pin: PA1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 

config/generic-fysetc-s6.cfg

@@ -113,42 +113,36 @@ max_z_accel: 100
 #uart_pin: PE8
 #tx_pin: PE9
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_y]
 #uart_pin: PE13
 #tx_pin: PE14
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_z]
 #uart_pin: PD12
 #tx_pin: PD11
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder]
 #uart_pin: PA15
 #tx_pin: PD3
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder1]
 #uart_pin: PC5
 #tx_pin: PC4
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder2]
 #uart_pin: PE0
 #tx_pin: PE1
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 ########################################
@@ -171,7 +165,6 @@ max_z_accel: 100
 #cs_pin: PE7
 #diag1_pin: PB14
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_y]
@@ -179,7 +172,6 @@ max_z_accel: 100
 #cs_pin: PE15
 #diag1_pin: PB13
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_z]
@@ -187,7 +179,6 @@ max_z_accel: 100
 #cs_pin: PD10
 #diag1_pin: PA0
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder]
@@ -195,7 +186,6 @@ max_z_accel: 100
 #cs_pin: PD7
 #diag1_pin: PA3
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder1]
@@ -203,7 +193,6 @@ max_z_accel: 100
 #cs_pin: PC14
 #diag1_pin: PA2
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder2]
@@ -211,7 +200,6 @@ max_z_accel: 100
 #cs_pin: PC15
 #diag1_pin: PA1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 ########################################

config/generic-fysetc-spider.cfg

@@ -129,50 +129,42 @@ max_z_accel: 100
 #[tmc2208 stepper_x]
 #uart_pin: PE7
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_y]
 #uart_pin: PE15
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_z]
 #uart_pin: PD10
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder]
 #uart_pin: PD7
 #run_current: 0.8
-#hold_current: 0.5
 #sense_resistor: 0.110
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder1]
 #uart_pin: PC14
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder2]
 #uart_pin: PC15
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder3]
 #uart_pin: PA15
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder4]
 #uart_pin: PD11
 #run_current: 0.8
-#hold_current: 0.5
 #stealthchop_threshold: 999999
 
 ########################################
@@ -184,7 +176,6 @@ max_z_accel: 100
 #cs_pin: PE7
 #diag1_pin: PB14
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_y]
@@ -192,7 +183,6 @@ max_z_accel: 100
 #cs_pin: PE15
 #diag1_pin: PB13
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_z]
@@ -200,7 +190,6 @@ max_z_accel: 100
 #cs_pin: PD10
 #diag1_pin: PA0
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder]
@@ -208,7 +197,6 @@ max_z_accel: 100
 #cs_pin: PD7
 #diag1_pin: PA3
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder1]
@@ -216,7 +204,6 @@ max_z_accel: 100
 #cs_pin: PC14
 #diag1_pin: PA2
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder2]
@@ -224,21 +211,18 @@ max_z_accel: 100
 #cs_pin: PC15
 #diag1_pin: PA1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder3]
 #spi_bus: spi4
 #cs_pin: PA15
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder4]
 #spi_bus: spi4
 #cs_pin: PD11
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 ########################################

config/generic-mellow-super-infinty-hv.cfg

@@ -188,49 +188,41 @@ max_z_accel: 100
 #[tmc2208 stepper_x]
 #uart_pin: PC4
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_y]
 #uart_pin: PF12
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_z]
 #uart_pin: PF15
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder]
 #uart_pin: PE7
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder1]
 #uart_pin: PE10
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder2]
 #uart_pin: PF1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder3]
 #uart_pin: PG2
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder4]
 #uart_pin: PG5
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 
@@ -253,7 +245,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: PB3
 ##diag1_pin: PG12
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc5160 stepper_y]
@@ -263,7 +254,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: PB3
 ##diag1_pin: PG11
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc5160 stepper_z]
@@ -273,7 +263,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: PB3
 ##diag1_pin: PG10
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 
 #[tmc5160 extruder]
@@ -283,7 +272,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: PB3
 ##diag1_pin: PG9
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc5160 extruder1]
@@ -293,7 +281,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: PB3
 ##diag1_pin: PD7
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc5160 extruder2]
@@ -303,7 +290,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: PB3
 ##diag1_pin: PD6
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc5160 extruder3]
@@ -313,7 +299,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: PB3
 ##diag1_pin: PA8
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc5160 extruder4]
@@ -323,7 +308,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: PB3
 ##diag1_pin: PF3
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 

config/generic-mks-robin-e3.cfg

@@ -70,25 +70,21 @@ max_temp: 250
 [tmc2209 stepper_x]
 uart_pin: PC7
 run_current: 0.800
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [tmc2209 stepper_y]
 uart_pin: PD2
 run_current: 0.800
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [tmc2209 stepper_z]
 uart_pin: PC12
 run_current: 0.650
-hold_current: 0.450
 stealthchop_threshold: 999999
 
 [tmc2209 extruder]
 uart_pin: PC11
 run_current: 0.800
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [fan]

config/generic-mks-rumba32-v1.0.cfg

@@ -119,21 +119,18 @@ aliases:
 #uart_pin: PC14
 ##tx_pin: PA3
 #run_current: 0.800
-#hold_current: 0.800
 #diag_pin:
 
 #[tmc2209 stepper_y]
 #uart_pin: PE4
 ##tx_pin: PA4
 #run_current: 0.800
-#hold_current: 0.800
 #diag_pin:
 
 #[tmc2209 stepper_z]
 #uart_pin: PE0
 ##tx_pin: PD13
 #run_current: 0.800
-#hold_current: 0.800
 #diag_pin:
 
 #[tmc2209 extruder]

config/generic-mks-sgenl.cfg

@@ -90,31 +90,26 @@ max_z_accel: 100
 #[tmc2208 stepper_x]
 #uart_pin: P1.1
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_y]
 #uart_pin: P1.8
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 stepper_z]
 #uart_pin: P1.10
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder]
 #uart_pin: P1.15
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2208 extruder1]
 #uart_pin: P1.17
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 
@@ -129,7 +124,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: P0.4
 ##diag1_pin: ^!P1.29
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_y]
@@ -139,7 +133,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: P0.4
 ##diag1_pin: ^!P1.27
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 stepper_z]
@@ -149,7 +142,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: P0.4
 ##diag1_pin: ^!P1.25
 #run_current: 0.650
-#hold_current: 0.450
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder]
@@ -159,7 +151,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: P0.4
 ##diag1_pin: ^!P1.28
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 #[tmc2130 extruder1]
@@ -169,7 +160,6 @@ max_z_accel: 100
 #spi_software_sclk_pin: P0.4
 ##diag1_pin: ^!P1.26
 #run_current: 0.800
-#hold_current: 0.500
 #stealthchop_threshold: 999999
 
 

config/generic-th3d-ezboard-lite-v1.2.cfg

@@ -33,7 +33,6 @@ position_max: 350
 uart_pin: P0.5
 tx_pin: P0.4
 run_current: 0.600
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_y]
@@ -50,7 +49,6 @@ position_max: 350
 uart_pin: P0.11
 tx_pin: P0.10
 run_current: 0.600
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [stepper_z]
@@ -67,7 +65,6 @@ position_max: 400
 uart_pin: P0.20
 tx_pin: P0.19
 run_current: 0.700
-hold_current: 0.600
 stealthchop_threshold: 999999
 
 [extruder]
@@ -92,7 +89,6 @@ max_temp: 210
 uart_pin: P0.21
 tx_pin: P0.22
 run_current: 0.800
-hold_current: 0.700
 stealthchop_threshold: 999999
 
 [heater_bed]

config/sample-bigtreetech-exp-mot.cfg

@@ -34,7 +34,6 @@ position_max: 400
 uart_pin: EXP1_6
 microsteps: 16
 run_current: 0.800
-hold_current: 0.500
 stealthchop_threshold: 999999
 diag_pin: EXP1_5
 
@@ -42,7 +41,6 @@ diag_pin: EXP1_5
 uart_pin: EXP1_4
 microsteps: 16
 run_current: 0.800
-hold_current: 0.500
 stealthchop_threshold: 999999
 diag_pin: EXP1_3
 
@@ -50,6 +48,5 @@ diag_pin: EXP1_3
 uart_pin: EXP1_2
 microsteps: 16
 run_current: 0.650
-hold_current: 0.450
 stealthchop_threshold: 999999
 diag_pin: EXP1_1

config/sample-bigtreetech-hermit-crab-canbus.cfg

@@ -35,7 +35,6 @@ max_temp: 250
 [tmc2209 extruder]
 uart_pin: HermitCrab: PB0
 run_current: 0.650
-hold_current: 0.500
 stealthchop_threshold: 999999
 
 [fan]

config/sample-mmu2s-diy.cfg

@@ -36,7 +36,6 @@ endstop_pin: ^mmboard:PC2 # PINDA X+
 [tmc2208 manual_stepper gear_stepper]
 uart_pin: mmboard:PC14
 run_current: 1.000
-hold_current: 0.600
 interpolate: True
 sense_resistor: 0.110
 
@@ -53,7 +52,6 @@ accel: 80
 [tmc2209 manual_stepper idler_stepper]
 uart_pin: mmboard:PB7
 run_current: 0.800
-hold_current: 0.800
 interpolate: True
 sense_resistor: 0.110
 stealthchop_threshold: 999999
@@ -73,7 +71,6 @@ endstop_pin: !mmboard:PC0 # switch endstop on the left Z-
 [tmc2209 manual_stepper selector_stepper]
 uart_pin: mmboard:PC12
 run_current: 1.000
-hold_current: 0.400
 interpolate: True
 sense_resistor: 0.110
 stealthchop_threshold: 999999

docs/TMC_Drivers.md

@@ -317,9 +317,7 @@ for the driver's internal stall flag to still be set from a previous
 move.
 
 It can also be useful to have that macro set the driver current before
-homing and set a new current after the carriage has moved away. This
+homing and set a new current after the carriage has moved away.
-also allows a hold_current to be set during prints (a hold_current
-is not recommended during sensorless homing).
 
 An example macro might look something like:
 ```
@@ -328,9 +326,8 @@ gcode:
     {% set HOME_CUR = 0.700 %}
     {% set driver_config = printer.configfile.settings['tmc2209 stepper_x'] %}
     {% set RUN_CUR = driver_config.run_current %}
-    {% set HOLD_CUR = driver_config.hold_current %}
     # Set current for sensorless homing
-    SET_TMC_CURRENT STEPPER=stepper_x CURRENT={HOME_CUR} HOLDCURRENT={HOME_CUR}
+    SET_TMC_CURRENT STEPPER=stepper_x CURRENT={HOME_CUR}
     # Pause to ensure driver stall flag is clear
     G4 P2000
     # Home
@@ -339,7 +336,7 @@ gcode:
     G90
     G1 X5 F1200
     # Set current during print
-    SET_TMC_CURRENT STEPPER=stepper_x CURRENT={RUN_CUR} HOLDCURRENT={HOLD_CUR}
+    SET_TMC_CURRENT STEPPER=stepper_x CURRENT={RUN_CUR}
 ```
 
 The resulting macro can be called from a
@@ -360,7 +357,7 @@ Use the tuning guide described above to find the appropriate "stall
 sensitivity" for each carriage, but be aware of the following
 restrictions:
 1. When using sensorless homing on CoreXY, make sure there is no
-   `hold_current` in effect for either stepper during homing.
+   `hold_current` configured for either stepper.
 2. While tuning, make sure both the X and Y carriages are near the
    center of their rails before each home attempt.
 3. After tuning is complete, when homing both X and Y, use macros to