diff --git a/config/generic-bigtreetech-e3-rrf-v1.1.cfg b/config/generic-bigtreetech-e3-rrf-v1.1.cfg index e8560020..557009ee 100644 --- a/config/generic-bigtreetech-e3-rrf-v1.1.cfg +++ b/config/generic-bigtreetech-e3-rrf-v1.1.cfg @@ -23,7 +23,6 @@ homing_speed: 50 [tmc2209 stepper_x] uart_pin: PD6 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_y] @@ -40,7 +39,6 @@ homing_speed: 50 [tmc2209 stepper_y] uart_pin: PD1 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_z] @@ -56,7 +54,6 @@ position_max: 250 [tmc2209 stepper_z] uart_pin: PD15 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [extruder] @@ -80,7 +77,6 @@ max_temp: 250 [tmc2209 extruder] uart_pin: PD11 run_current: 0.650 -hold_current: 0.500 stealthchop_threshold: 999999 [heater_bed] diff --git a/config/generic-bigtreetech-gtr.cfg b/config/generic-bigtreetech-gtr.cfg index 07b6632e..a562afee 100644 --- a/config/generic-bigtreetech-gtr.cfg +++ b/config/generic-bigtreetech-gtr.cfg @@ -126,37 +126,31 @@ max_z_accel: 5 #[tmc2208 stepper_x] #uart_pin: PC14 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 stepper_y] #uart_pin: PE1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 stepper_z] #uart_pin: PB5 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 #[tmc2208 extruder] #uart_pin: PG10 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder1] #uart_pin: PD4 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder2] #uart_pin: PC12 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 @@ -167,7 +161,6 @@ max_z_accel: 5 #[tmc2130 stepper_x] #cs_pin: PC14 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 0 #spi_software_mosi_pin: PG15 #spi_software_miso_pin: PB6 @@ -177,7 +170,6 @@ max_z_accel: 5 #cs_pin: PE1 #sense_resistor: 0.075 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 0 #spi_software_mosi_pin: PG15 #spi_software_miso_pin: PB6 @@ -187,7 +179,6 @@ max_z_accel: 5 #cs_pin: PB5 #sense_resistor: 0.075 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 0 #spi_software_mosi_pin: PG15 #spi_software_miso_pin: PB6 @@ -197,7 +188,6 @@ max_z_accel: 5 #cs_pin: PG10 #sense_resistor: 0.075 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 0 #spi_software_mosi_pin: PG15 #spi_software_miso_pin: PB6 @@ -207,7 +197,6 @@ max_z_accel: 5 #cs_pin: PD4 #sense_resistor: 0.075 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 0 #spi_software_mosi_pin: PG15 #spi_software_miso_pin: PB6 @@ -217,7 +206,6 @@ max_z_accel: 5 #cs_pin: PC12 #sense_resistor: 0.075 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 0 #spi_software_mosi_pin: PG15 #spi_software_miso_pin: PB6 @@ -232,7 +220,6 @@ max_z_accel: 5 #sense_resistor: 0.075 #interpolate: True #run_current: 1 -#hold_current: 1 #stealthchop_threshold: 0 #spi_software_mosi_pin: PG15 #spi_software_miso_pin: PB6 @@ -243,7 +230,6 @@ max_z_accel: 5 #sense_resistor: 0.075 #interpolate: True #run_current: 1 -#hold_current: 1 #stealthchop_threshold: 0 #spi_software_mosi_pin: PG15 #spi_software_miso_pin: PB6 @@ -254,7 +240,6 @@ max_z_accel: 5 #sense_resistor: 0.075 #interpolate: True #run_current: 0.4 -#hold_current: 0.4 #stealthchop_threshold: 0 #spi_software_mosi_pin: PG15 #spi_software_miso_pin: PB6 @@ -265,7 +250,6 @@ max_z_accel: 5 #sense_resistor: 0.075 #interpolate: True #run_current: 0.5 -#hold_current: 0.5 #stealthchop_threshold: 0 #spi_software_mosi_pin: PG15 #spi_software_miso_pin: PB6 @@ -276,7 +260,6 @@ max_z_accel: 5 #sense_resistor: 0.075 #interpolate: True #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 0 #spi_software_mosi_pin: PG15 #spi_software_miso_pin: PB6 @@ -287,7 +270,6 @@ max_z_accel: 5 #sense_resistor: 0.075 #interpolate: True #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 0 #spi_software_mosi_pin: PG15 #spi_software_miso_pin: PB6 diff --git a/config/generic-bigtreetech-octopus.cfg b/config/generic-bigtreetech-octopus.cfg index 04bef072..d8deb0da 100644 --- a/config/generic-bigtreetech-octopus.cfg +++ b/config/generic-bigtreetech-octopus.cfg @@ -153,52 +153,44 @@ max_z_accel: 100 #uart_pin: PC4 ##diag_pin: PG6 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2209 stepper_y] #uart_pin: PD11 ##diag_pin: PG9 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2209 stepper_z] #uart_pin: PC6 ##diag_pin: PG10 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 #[tmc2209 stepper_] #uart_pin: PC7 ##diag_pin: PG11 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 #[tmc2209 extruder] #uart_pin: PF2 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2209 extruder1] #uart_pin: PE4 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2209 extruder2] #uart_pin: PE1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2209 extruder3] #uart_pin: PD3 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 ######################################## @@ -210,7 +202,6 @@ max_z_accel: 100 #spi_bus: spi1 ##diag1_pin: PG6 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_y] @@ -218,7 +209,6 @@ max_z_accel: 100 #spi_bus: spi1 ##diag1_pin: PG9 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_z] @@ -226,7 +216,6 @@ max_z_accel: 100 #spi_bus: spi1 ##diag1_pin: PG10 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 #[tmc2130 stepper_] @@ -234,35 +223,30 @@ max_z_accel: 100 #spi_bus: spi1 ##diag1_pin: PG11 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder] #cs_pin: PF2 #spi_bus: spi1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder1] #cs_pin: PE4 #spi_bus: spi1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder2] #cs_pin: PE1 #spi_bus: spi1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder3] #cs_pin: PD3 #spi_bus: spi1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 [board_pins] diff --git a/config/generic-bigtreetech-skr-2.cfg b/config/generic-bigtreetech-skr-2.cfg index d32d2e41..dd422609 100644 --- a/config/generic-bigtreetech-skr-2.cfg +++ b/config/generic-bigtreetech-skr-2.cfg @@ -132,19 +132,16 @@ aliases: #[tmc2209 stepper_x] #uart_pin: PE0 #run_current: 0.800 -#hold_current: 0.800 #diag_pin: #[tmc2209 stepper_y] #uart_pin: PD3 #run_current: 0.800 -#hold_current: 0.800 #diag_pin: #[tmc2209 stepper_z] #uart_pin: PD0 #run_current: 0.800 -#hold_current: 0.800 #diag_pin: #[tmc2209 extruder] diff --git a/config/generic-bigtreetech-skr-cr6-v1.0.cfg b/config/generic-bigtreetech-skr-cr6-v1.0.cfg index d14deb18..18e5ce5b 100644 --- a/config/generic-bigtreetech-skr-cr6-v1.0.cfg +++ b/config/generic-bigtreetech-skr-cr6-v1.0.cfg @@ -27,7 +27,6 @@ homing_speed: 50 uart_pin: PC11 tx_pin: PC10 run_current: 0.550 -hold_current: 0.450 stealthchop_threshold: 999999 uart_address: 0 @@ -48,7 +47,6 @@ uart_pin: PC11 tx_pin: PC10 uart_address: 2 run_current: 0.550 -hold_current: 0.450 stealthchop_threshold: 999999 [stepper_z] @@ -67,7 +65,6 @@ uart_pin: PC11 tx_pin: PC10 uart_address: 1 run_current: 0.550 -hold_current: 0.450 stealthchop_threshold: 999999 [extruder] @@ -93,7 +90,6 @@ uart_pin: PC11 tx_pin: PC10 uart_address: 3 run_current: 0.600 -hold_current: 0.400 stealthchop_threshold: 999999 [heater_bed] diff --git a/config/generic-bigtreetech-skr-e3-dip.cfg b/config/generic-bigtreetech-skr-e3-dip.cfg index 44866959..10ae56d1 100644 --- a/config/generic-bigtreetech-skr-e3-dip.cfg +++ b/config/generic-bigtreetech-skr-e3-dip.cfg @@ -99,25 +99,21 @@ pins: !PC13 #[tmc2208 stepper_x] #uart_pin: PC10 #run_current: 0.580 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 stepper_y] #uart_pin: PC11 #run_current: 0.580 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 stepper_z] #uart_pin: PC12 #run_current: 0.580 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder] #uart_pin: PD2 #run_current: 0.650 -#hold_current: 0.500 #stealthchop_threshold: 999999 @@ -129,28 +125,24 @@ pins: !PC13 #cs_pin: PC10 #spi_bus: spi3 #run_current: 0.580 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_y] #cs_pin: PC11 #spi_bus: spi3 #run_current: 0.580 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_z] #cs_pin: PC12 #spi_bus: spi3 #run_current: 0.580 -#hold_current: 0.450 #stealthchop_threshold: 999999 #[tmc2130 extruder] #cs_pin: PD2 #spi_bus: spi3 #run_current: 0.650 -#hold_current: 0.500 #stealthchop_threshold: 999999 diff --git a/config/generic-bigtreetech-skr-e3-turbo.cfg b/config/generic-bigtreetech-skr-e3-turbo.cfg index b01a993a..1974afdb 100644 --- a/config/generic-bigtreetech-skr-e3-turbo.cfg +++ b/config/generic-bigtreetech-skr-e3-turbo.cfg @@ -19,7 +19,6 @@ homing_speed: 50 uart_pin: P1.1 #diag_pin: P1.29 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_y] @@ -37,7 +36,6 @@ homing_speed: 50 uart_pin: P1.10 #diag_pin: P1.28 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_z] @@ -54,7 +52,6 @@ position_max: 250 uart_pin: P1.17 #diag_pin: P1.27 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [extruder] @@ -79,7 +76,6 @@ max_temp: 250 uart_pin: P0.5 #diag_pin: P1.26 run_current: 0.650 -hold_current: 0.500 stealthchop_threshold: 999999 #[extruder1] diff --git a/config/generic-bigtreetech-skr-mini-e3-v1.0.cfg b/config/generic-bigtreetech-skr-mini-e3-v1.0.cfg index 671f7738..aea833b4 100644 --- a/config/generic-bigtreetech-skr-mini-e3-v1.0.cfg +++ b/config/generic-bigtreetech-skr-mini-e3-v1.0.cfg @@ -30,7 +30,6 @@ uart_pin: PC11 tx_pin: PC10 uart_address: 0 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_y] @@ -49,7 +48,6 @@ uart_pin: PC11 tx_pin: PC10 uart_address: 2 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_z] @@ -67,7 +65,6 @@ uart_pin: PC11 tx_pin: PC10 uart_address: 1 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [extruder] @@ -93,7 +90,6 @@ uart_pin: PC11 tx_pin: PC10 uart_address: 3 run_current: 0.650 -hold_current: 0.500 stealthchop_threshold: 999999 [heater_bed] diff --git a/config/generic-bigtreetech-skr-mini-e3-v1.2.cfg b/config/generic-bigtreetech-skr-mini-e3-v1.2.cfg index f4c13a92..a5a306a2 100644 --- a/config/generic-bigtreetech-skr-mini-e3-v1.2.cfg +++ b/config/generic-bigtreetech-skr-mini-e3-v1.2.cfg @@ -28,7 +28,6 @@ homing_speed: 50 [tmc2209 stepper_x] uart_pin: PB15 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_y] @@ -45,7 +44,6 @@ homing_speed: 50 [tmc2209 stepper_y] uart_pin: PC6 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_z] @@ -61,7 +59,6 @@ position_max: 250 [tmc2209 stepper_z] uart_pin: PC10 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [extruder] @@ -85,7 +82,6 @@ max_temp: 250 [tmc2209 extruder] uart_pin: PC11 run_current: 0.650 -hold_current: 0.500 stealthchop_threshold: 999999 [heater_bed] diff --git a/config/generic-bigtreetech-skr-mini-e3-v2.0.cfg b/config/generic-bigtreetech-skr-mini-e3-v2.0.cfg index 848b8d52..96605da1 100644 --- a/config/generic-bigtreetech-skr-mini-e3-v2.0.cfg +++ b/config/generic-bigtreetech-skr-mini-e3-v2.0.cfg @@ -27,7 +27,6 @@ uart_pin: PC11 tx_pin: PC10 uart_address: 0 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_y] @@ -46,7 +45,6 @@ uart_pin: PC11 tx_pin: PC10 uart_address: 2 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_z] @@ -64,7 +62,6 @@ uart_pin: PC11 tx_pin: PC10 uart_address: 1 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [extruder] @@ -90,7 +87,6 @@ uart_pin: PC11 tx_pin: PC10 uart_address: 3 run_current: 0.650 -hold_current: 0.500 stealthchop_threshold: 999999 [heater_bed] diff --git a/config/generic-bigtreetech-skr-mini-mz.cfg b/config/generic-bigtreetech-skr-mini-mz.cfg index e632690f..15f32864 100644 --- a/config/generic-bigtreetech-skr-mini-mz.cfg +++ b/config/generic-bigtreetech-skr-mini-mz.cfg @@ -30,7 +30,6 @@ uart_pin: PC11 tx_pin: PC10 uart_address: 0 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_y] @@ -49,7 +48,6 @@ uart_pin: PC11 tx_pin: PC10 uart_address: 1 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_z] @@ -67,7 +65,6 @@ uart_pin: PC11 tx_pin: PC10 uart_address: 2 run_current: 0.580 -hold_current: 0.500 stealthchop_threshold: 999999 [extruder] @@ -93,7 +90,6 @@ uart_pin: PC11 tx_pin: PC10 uart_address: 3 run_current: 0.650 -hold_current: 0.500 stealthchop_threshold: 999999 [heater_bed] diff --git a/config/generic-bigtreetech-skr-pro.cfg b/config/generic-bigtreetech-skr-pro.cfg index 9682097b..cb7d3c2c 100644 --- a/config/generic-bigtreetech-skr-pro.cfg +++ b/config/generic-bigtreetech-skr-pro.cfg @@ -110,37 +110,31 @@ max_z_accel: 100 #[tmc2208 stepper_x] #uart_pin: PC13 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 stepper_y] #uart_pin: PE3 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 stepper_z] #uart_pin: PE1 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 #[tmc2208 extruder] #uart_pin: PD4 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder1] #uart_pin: PD1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder2] #uart_pin: PD6 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 @@ -153,7 +147,6 @@ max_z_accel: 100 #spi_bus: spi3a ##diag1_pin: PB10 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_y] @@ -161,7 +154,6 @@ max_z_accel: 100 #spi_bus: spi3a ##diag1_pin: PE12 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_z] @@ -169,7 +161,6 @@ max_z_accel: 100 #spi_bus: spi3a ##diag1_pin: PG8 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 #[tmc2130 extruder] @@ -177,7 +168,6 @@ max_z_accel: 100 #spi_bus: spi3a ##diag1_pin: PE15 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder1] @@ -185,7 +175,6 @@ max_z_accel: 100 #spi_bus: spi3a ##diag1_pin: PE10 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder2] @@ -193,7 +182,6 @@ max_z_accel: 100 #spi_bus: spi3a ##diag1_pin: PG5 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 diff --git a/config/generic-bigtreetech-skr-v1.3.cfg b/config/generic-bigtreetech-skr-v1.3.cfg index ab1df53b..209deeb1 100644 --- a/config/generic-bigtreetech-skr-v1.3.cfg +++ b/config/generic-bigtreetech-skr-v1.3.cfg @@ -95,31 +95,26 @@ max_z_accel: 100 #[tmc2208 stepper_x] #uart_pin: P1.17 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 stepper_y] #uart_pin: P1.15 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 stepper_z] #uart_pin: P1.10 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 #[tmc2208 extruder] #uart_pin: P1.8 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder1] #uart_pin: P1.1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 @@ -138,7 +133,6 @@ max_z_accel: 100 #spi_software_sclk_pin: P0.4 ##diag1_pin: P1.29 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_y] @@ -148,7 +142,6 @@ max_z_accel: 100 #spi_software_sclk_pin: P0.4 ##diag1_pin: P1.27 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_z] @@ -158,7 +151,6 @@ max_z_accel: 100 #spi_software_sclk_pin: P0.4 ##diag1_pin: P1.25 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 #[tmc2130 extruder] @@ -168,7 +160,6 @@ max_z_accel: 100 #spi_software_sclk_pin: P0.4 ##diag1_pin: P1.28 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder1] @@ -178,7 +169,6 @@ max_z_accel: 100 #spi_software_sclk_pin: P0.4 ##diag1_pin: P1.26 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 diff --git a/config/generic-bigtreetech-skr-v1.4.cfg b/config/generic-bigtreetech-skr-v1.4.cfg index 17141017..5be2dff9 100644 --- a/config/generic-bigtreetech-skr-v1.4.cfg +++ b/config/generic-bigtreetech-skr-v1.4.cfg @@ -94,31 +94,26 @@ max_z_accel: 100 #[tmc2208 stepper_x] #uart_pin: P1.10 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 # #[tmc2208 stepper_y] #uart_pin: P1.9 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 # #[tmc2208 stepper_z] #uart_pin: P1.8 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 # #[tmc2208 extruder] #uart_pin: P1.4 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 # #[tmc2208 extruder1] #uart_pin: P1.1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 @@ -132,7 +127,6 @@ max_z_accel: 100 #spi_software_mosi_pin: P1.17 #spi_software_sclk_pin: P0.4 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #diag1_pin: P1.29 @@ -142,7 +136,6 @@ max_z_accel: 100 #spi_software_mosi_pin: P1.17 #spi_software_sclk_pin: P0.4 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #diag1_pin: P1.28 @@ -152,7 +145,6 @@ max_z_accel: 100 #spi_software_mosi_pin: P1.17 #spi_software_sclk_pin: P0.4 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 #diag1_pin: P1.27 @@ -162,7 +154,6 @@ max_z_accel: 100 #spi_software_mosi_pin: P1.17 #spi_software_sclk_pin: P0.4 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #diag1_pin: P1.26 @@ -172,7 +163,6 @@ max_z_accel: 100 #spi_software_mosi_pin: P1.17 #spi_software_sclk_pin: P0.4 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #diag1_pin: P1.25 diff --git a/config/generic-flyboard.cfg b/config/generic-flyboard.cfg index 7e5727ed..053af01f 100644 --- a/config/generic-flyboard.cfg +++ b/config/generic-flyboard.cfg @@ -144,55 +144,46 @@ max_z_accel: 100 #[tmc2208 stepper_x] #uart_pin: PG13 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 stepper_y] #uart_pin: PG10 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 stepper_z] #uart_pin: PD5 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 #[tmc2208 extruder] #uart_pin: PD1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder1] #uart_pin: PA14 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder2] #uart_pin: PG6 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder3] #uart_pin: PG3 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder4] #uart_pin: PD10 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder5] #uart_pin: PB12 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 @@ -204,63 +195,54 @@ max_z_accel: 100 #cs_pin: PG13 ##diag1_pin: PC3 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_y] #cs_pin: PG10 ##diag1_pin: PF2 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_z] #cs_pin: PBD5 ##diag1_pin: PF0 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 #[tmc2130 extruder] #cs_pin: PD1 ##diag1_pin: PE15 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder1] #cs_pin: PA14 ##diag1_pin: PE10 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder2] #cs_pin: PG6 ##diag1_pin: PC15 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder3] #cs_pin: PG3 ##diag1_pin: PC15 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder4] #cs_pin: PD10 ##diag1_pin: PC15 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder5] #cs_pin: PB12 ##diag1_pin: PC15 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 diff --git a/config/generic-fysetc-cheetah-v1.1.cfg b/config/generic-fysetc-cheetah-v1.1.cfg index 4b604447..8ae36513 100644 --- a/config/generic-fysetc-cheetah-v1.1.cfg +++ b/config/generic-fysetc-cheetah-v1.1.cfg @@ -25,7 +25,6 @@ uart_pin: PA3 tx_pin: PA2 uart_address: 0 run_current: 0.800 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_y] @@ -44,7 +43,6 @@ uart_pin: PA3 tx_pin: PA2 uart_address: 2 run_current: 0.800 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_z] @@ -62,7 +60,6 @@ uart_pin: PA3 tx_pin: PA2 uart_address: 1 run_current: 0.800 -hold_current: 0.500 stealthchop_threshold: 999999 [extruder] @@ -88,7 +85,6 @@ uart_pin: PA3 tx_pin: PA2 uart_address: 3 run_current: 1.0 -hold_current: 0.500 stealthchop_threshold: 999999 [heater_bed] diff --git a/config/generic-fysetc-cheetah-v1.2.cfg b/config/generic-fysetc-cheetah-v1.2.cfg index d0f3a755..1474b837 100644 --- a/config/generic-fysetc-cheetah-v1.2.cfg +++ b/config/generic-fysetc-cheetah-v1.2.cfg @@ -24,7 +24,6 @@ homing_speed: 50 uart_pin: PA12 tx_pin: PA11 run_current: 0.800 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_y] @@ -42,7 +41,6 @@ homing_speed: 50 uart_pin: PB7 tx_pin: PB6 run_current: 0.800 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_z] @@ -59,7 +57,6 @@ position_max: 200 uart_pin: PB11 tx_pin: PB10 run_current: 0.800 -hold_current: 0.500 stealthchop_threshold: 999999 [extruder] @@ -84,7 +81,6 @@ max_temp: 250 uart_pin: PA3 tx_pin: PA2 run_current: 1.0 -hold_current: 0.500 stealthchop_threshold: 999999 [heater_bed] diff --git a/config/generic-fysetc-f6.cfg b/config/generic-fysetc-f6.cfg index 31397543..4cca44d5 100644 --- a/config/generic-fysetc-f6.cfg +++ b/config/generic-fysetc-f6.cfg @@ -112,42 +112,36 @@ pins: PB0 #uart_pin: PG3 #tx_pin: PJ2 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 stepper_y] #uart_pin: PJ3 #tx_pin: PJ4 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 stepper_z] #uart_pin: PE2 #tx_pin: PE6 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 extruder] #uart_pin: PJ5 #tx_pin: PJ6 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 extruder1] #uart_pin: PE7 #tx_pin: PD4 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 extruder2] #uart_pin: PA1 #tx_pin: PD5 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 ######################################## @@ -166,42 +160,36 @@ pins: PB0 #cs_pin: PG4 #diag1_pin: PK1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_y] #cs_pin: PG2 #diag1_pin: PJ1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_z] #cs_pin: PJ7 #diag1_pin: PB6 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder] #cs_pin: PL2 #diag1_pin: PE4 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder1] #cs_pin: PC5 #diag1_pin: PJ0 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder2] #cs_pin: PL7 #diag1_pin: PK2 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 ######################################## diff --git a/config/generic-fysetc-s6-v2.cfg b/config/generic-fysetc-s6-v2.cfg index cdc9190d..21c24b0f 100644 --- a/config/generic-fysetc-s6-v2.cfg +++ b/config/generic-fysetc-s6-v2.cfg @@ -106,37 +106,31 @@ max_z_accel: 100 #[tmc2208 stepper_x] #uart_pin: PE8 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 stepper_y] #uart_pin: PC4 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 stepper_z] #uart_pin: PD12 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 extruder] #uart_pin: PA15 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 extruder1] #uart_pin: PC5 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 extruder2] #uart_pin: PE0 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 @@ -149,7 +143,6 @@ max_z_accel: 100 #cs_pin: PE7 #diag1_pin: PB14 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_y] @@ -157,7 +150,6 @@ max_z_accel: 100 #cs_pin: PE15 #diag1_pin: PB13 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_z] @@ -165,7 +157,6 @@ max_z_accel: 100 #cs_pin: PD10 #diag1_pin: PA0 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder] @@ -173,7 +164,6 @@ max_z_accel: 100 #cs_pin: PD7 #diag1_pin: PA3 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder1] @@ -181,7 +171,6 @@ max_z_accel: 100 #cs_pin: PC14 #diag1_pin: PA2 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder2] @@ -189,7 +178,6 @@ max_z_accel: 100 #cs_pin: PC15 #diag1_pin: PA1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 diff --git a/config/generic-fysetc-s6.cfg b/config/generic-fysetc-s6.cfg index 0f212665..ff2b077e 100644 --- a/config/generic-fysetc-s6.cfg +++ b/config/generic-fysetc-s6.cfg @@ -113,42 +113,36 @@ max_z_accel: 100 #uart_pin: PE8 #tx_pin: PE9 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 stepper_y] #uart_pin: PE13 #tx_pin: PE14 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 stepper_z] #uart_pin: PD12 #tx_pin: PD11 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 extruder] #uart_pin: PA15 #tx_pin: PD3 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 extruder1] #uart_pin: PC5 #tx_pin: PC4 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 extruder2] #uart_pin: PE0 #tx_pin: PE1 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 ######################################## @@ -171,7 +165,6 @@ max_z_accel: 100 #cs_pin: PE7 #diag1_pin: PB14 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_y] @@ -179,7 +172,6 @@ max_z_accel: 100 #cs_pin: PE15 #diag1_pin: PB13 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_z] @@ -187,7 +179,6 @@ max_z_accel: 100 #cs_pin: PD10 #diag1_pin: PA0 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder] @@ -195,7 +186,6 @@ max_z_accel: 100 #cs_pin: PD7 #diag1_pin: PA3 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder1] @@ -203,7 +193,6 @@ max_z_accel: 100 #cs_pin: PC14 #diag1_pin: PA2 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder2] @@ -211,7 +200,6 @@ max_z_accel: 100 #cs_pin: PC15 #diag1_pin: PA1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 ######################################## diff --git a/config/generic-fysetc-spider.cfg b/config/generic-fysetc-spider.cfg index 7c7ca56a..fa443b97 100644 --- a/config/generic-fysetc-spider.cfg +++ b/config/generic-fysetc-spider.cfg @@ -129,50 +129,42 @@ max_z_accel: 100 #[tmc2208 stepper_x] #uart_pin: PE7 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 stepper_y] #uart_pin: PE15 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 stepper_z] #uart_pin: PD10 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 extruder] #uart_pin: PD7 #run_current: 0.8 -#hold_current: 0.5 #sense_resistor: 0.110 #stealthchop_threshold: 999999 #[tmc2208 extruder1] #uart_pin: PC14 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 extruder2] #uart_pin: PC15 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 extruder3] #uart_pin: PA15 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 #[tmc2208 extruder4] #uart_pin: PD11 #run_current: 0.8 -#hold_current: 0.5 #stealthchop_threshold: 999999 ######################################## @@ -184,7 +176,6 @@ max_z_accel: 100 #cs_pin: PE7 #diag1_pin: PB14 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_y] @@ -192,7 +183,6 @@ max_z_accel: 100 #cs_pin: PE15 #diag1_pin: PB13 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_z] @@ -200,7 +190,6 @@ max_z_accel: 100 #cs_pin: PD10 #diag1_pin: PA0 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder] @@ -208,7 +197,6 @@ max_z_accel: 100 #cs_pin: PD7 #diag1_pin: PA3 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder1] @@ -216,7 +204,6 @@ max_z_accel: 100 #cs_pin: PC14 #diag1_pin: PA2 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder2] @@ -224,21 +211,18 @@ max_z_accel: 100 #cs_pin: PC15 #diag1_pin: PA1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder3] #spi_bus: spi4 #cs_pin: PA15 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder4] #spi_bus: spi4 #cs_pin: PD11 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 ######################################## diff --git a/config/generic-mellow-super-infinty-hv.cfg b/config/generic-mellow-super-infinty-hv.cfg index e35555df..28099487 100644 --- a/config/generic-mellow-super-infinty-hv.cfg +++ b/config/generic-mellow-super-infinty-hv.cfg @@ -188,49 +188,41 @@ max_z_accel: 100 #[tmc2208 stepper_x] #uart_pin: PC4 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 stepper_y] #uart_pin: PF12 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 stepper_z] #uart_pin: PF15 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 #[tmc2208 extruder] #uart_pin: PE7 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder1] #uart_pin: PE10 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder2] #uart_pin: PF1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder3] #uart_pin: PG2 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder4] #uart_pin: PG5 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 @@ -253,7 +245,6 @@ max_z_accel: 100 #spi_software_sclk_pin: PB3 ##diag1_pin: PG12 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc5160 stepper_y] @@ -263,7 +254,6 @@ max_z_accel: 100 #spi_software_sclk_pin: PB3 ##diag1_pin: PG11 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc5160 stepper_z] @@ -273,7 +263,6 @@ max_z_accel: 100 #spi_software_sclk_pin: PB3 ##diag1_pin: PG10 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 #[tmc5160 extruder] @@ -283,7 +272,6 @@ max_z_accel: 100 #spi_software_sclk_pin: PB3 ##diag1_pin: PG9 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc5160 extruder1] @@ -293,7 +281,6 @@ max_z_accel: 100 #spi_software_sclk_pin: PB3 ##diag1_pin: PD7 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc5160 extruder2] @@ -303,7 +290,6 @@ max_z_accel: 100 #spi_software_sclk_pin: PB3 ##diag1_pin: PD6 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc5160 extruder3] @@ -313,7 +299,6 @@ max_z_accel: 100 #spi_software_sclk_pin: PB3 ##diag1_pin: PA8 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc5160 extruder4] @@ -323,7 +308,6 @@ max_z_accel: 100 #spi_software_sclk_pin: PB3 ##diag1_pin: PF3 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 diff --git a/config/generic-mks-robin-e3.cfg b/config/generic-mks-robin-e3.cfg index f30f2a08..4f1016db 100644 --- a/config/generic-mks-robin-e3.cfg +++ b/config/generic-mks-robin-e3.cfg @@ -70,25 +70,21 @@ max_temp: 250 [tmc2209 stepper_x] uart_pin: PC7 run_current: 0.800 -hold_current: 0.500 stealthchop_threshold: 999999 [tmc2209 stepper_y] uart_pin: PD2 run_current: 0.800 -hold_current: 0.500 stealthchop_threshold: 999999 [tmc2209 stepper_z] uart_pin: PC12 run_current: 0.650 -hold_current: 0.450 stealthchop_threshold: 999999 [tmc2209 extruder] uart_pin: PC11 run_current: 0.800 -hold_current: 0.500 stealthchop_threshold: 999999 [fan] diff --git a/config/generic-mks-rumba32-v1.0.cfg b/config/generic-mks-rumba32-v1.0.cfg index a2cf5554..96da568a 100644 --- a/config/generic-mks-rumba32-v1.0.cfg +++ b/config/generic-mks-rumba32-v1.0.cfg @@ -119,21 +119,18 @@ aliases: #uart_pin: PC14 ##tx_pin: PA3 #run_current: 0.800 -#hold_current: 0.800 #diag_pin: #[tmc2209 stepper_y] #uart_pin: PE4 ##tx_pin: PA4 #run_current: 0.800 -#hold_current: 0.800 #diag_pin: #[tmc2209 stepper_z] #uart_pin: PE0 ##tx_pin: PD13 #run_current: 0.800 -#hold_current: 0.800 #diag_pin: #[tmc2209 extruder] diff --git a/config/generic-mks-sgenl.cfg b/config/generic-mks-sgenl.cfg index 68169a8c..dc411d63 100644 --- a/config/generic-mks-sgenl.cfg +++ b/config/generic-mks-sgenl.cfg @@ -90,31 +90,26 @@ max_z_accel: 100 #[tmc2208 stepper_x] #uart_pin: P1.1 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 stepper_y] #uart_pin: P1.8 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 stepper_z] #uart_pin: P1.10 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 #[tmc2208 extruder] #uart_pin: P1.15 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2208 extruder1] #uart_pin: P1.17 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 @@ -129,7 +124,6 @@ max_z_accel: 100 #spi_software_sclk_pin: P0.4 ##diag1_pin: ^!P1.29 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_y] @@ -139,7 +133,6 @@ max_z_accel: 100 #spi_software_sclk_pin: P0.4 ##diag1_pin: ^!P1.27 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 stepper_z] @@ -149,7 +142,6 @@ max_z_accel: 100 #spi_software_sclk_pin: P0.4 ##diag1_pin: ^!P1.25 #run_current: 0.650 -#hold_current: 0.450 #stealthchop_threshold: 999999 #[tmc2130 extruder] @@ -159,7 +151,6 @@ max_z_accel: 100 #spi_software_sclk_pin: P0.4 ##diag1_pin: ^!P1.28 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 #[tmc2130 extruder1] @@ -169,7 +160,6 @@ max_z_accel: 100 #spi_software_sclk_pin: P0.4 ##diag1_pin: ^!P1.26 #run_current: 0.800 -#hold_current: 0.500 #stealthchop_threshold: 999999 diff --git a/config/generic-th3d-ezboard-lite-v1.2.cfg b/config/generic-th3d-ezboard-lite-v1.2.cfg index 49661361..6fff88db 100644 --- a/config/generic-th3d-ezboard-lite-v1.2.cfg +++ b/config/generic-th3d-ezboard-lite-v1.2.cfg @@ -33,7 +33,6 @@ position_max: 350 uart_pin: P0.5 tx_pin: P0.4 run_current: 0.600 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_y] @@ -50,7 +49,6 @@ position_max: 350 uart_pin: P0.11 tx_pin: P0.10 run_current: 0.600 -hold_current: 0.500 stealthchop_threshold: 999999 [stepper_z] @@ -67,7 +65,6 @@ position_max: 400 uart_pin: P0.20 tx_pin: P0.19 run_current: 0.700 -hold_current: 0.600 stealthchop_threshold: 999999 [extruder] @@ -92,7 +89,6 @@ max_temp: 210 uart_pin: P0.21 tx_pin: P0.22 run_current: 0.800 -hold_current: 0.700 stealthchop_threshold: 999999 [heater_bed] diff --git a/config/sample-bigtreetech-exp-mot.cfg b/config/sample-bigtreetech-exp-mot.cfg index c7d8357d..ee1992e7 100644 --- a/config/sample-bigtreetech-exp-mot.cfg +++ b/config/sample-bigtreetech-exp-mot.cfg @@ -34,7 +34,6 @@ position_max: 400 uart_pin: EXP1_6 microsteps: 16 run_current: 0.800 -hold_current: 0.500 stealthchop_threshold: 999999 diag_pin: EXP1_5 @@ -42,7 +41,6 @@ diag_pin: EXP1_5 uart_pin: EXP1_4 microsteps: 16 run_current: 0.800 -hold_current: 0.500 stealthchop_threshold: 999999 diag_pin: EXP1_3 @@ -50,6 +48,5 @@ diag_pin: EXP1_3 uart_pin: EXP1_2 microsteps: 16 run_current: 0.650 -hold_current: 0.450 stealthchop_threshold: 999999 diag_pin: EXP1_1 diff --git a/config/sample-bigtreetech-hermit-crab-canbus.cfg b/config/sample-bigtreetech-hermit-crab-canbus.cfg index 95043248..ce3b3045 100644 --- a/config/sample-bigtreetech-hermit-crab-canbus.cfg +++ b/config/sample-bigtreetech-hermit-crab-canbus.cfg @@ -35,7 +35,6 @@ max_temp: 250 [tmc2209 extruder] uart_pin: HermitCrab: PB0 run_current: 0.650 -hold_current: 0.500 stealthchop_threshold: 999999 [fan] diff --git a/config/sample-mmu2s-diy.cfg b/config/sample-mmu2s-diy.cfg index c5c88802..80e8c058 100644 --- a/config/sample-mmu2s-diy.cfg +++ b/config/sample-mmu2s-diy.cfg @@ -36,7 +36,6 @@ endstop_pin: ^mmboard:PC2 # PINDA X+ [tmc2208 manual_stepper gear_stepper] uart_pin: mmboard:PC14 run_current: 1.000 -hold_current: 0.600 interpolate: True sense_resistor: 0.110 @@ -53,7 +52,6 @@ accel: 80 [tmc2209 manual_stepper idler_stepper] uart_pin: mmboard:PB7 run_current: 0.800 -hold_current: 0.800 interpolate: True sense_resistor: 0.110 stealthchop_threshold: 999999 @@ -73,7 +71,6 @@ endstop_pin: !mmboard:PC0 # switch endstop on the left Z- [tmc2209 manual_stepper selector_stepper] uart_pin: mmboard:PC12 run_current: 1.000 -hold_current: 0.400 interpolate: True sense_resistor: 0.110 stealthchop_threshold: 999999 diff --git a/docs/TMC_Drivers.md b/docs/TMC_Drivers.md index 99213cb8..df9dae1f 100644 --- a/docs/TMC_Drivers.md +++ b/docs/TMC_Drivers.md @@ -317,9 +317,7 @@ for the driver's internal stall flag to still be set from a previous move. It can also be useful to have that macro set the driver current before -homing and set a new current after the carriage has moved away. This -also allows a hold_current to be set during prints (a hold_current -is not recommended during sensorless homing). +homing and set a new current after the carriage has moved away. An example macro might look something like: ``` @@ -328,9 +326,8 @@ gcode: {% set HOME_CUR = 0.700 %} {% set driver_config = printer.configfile.settings['tmc2209 stepper_x'] %} {% set RUN_CUR = driver_config.run_current %} - {% set HOLD_CUR = driver_config.hold_current %} # Set current for sensorless homing - SET_TMC_CURRENT STEPPER=stepper_x CURRENT={HOME_CUR} HOLDCURRENT={HOME_CUR} + SET_TMC_CURRENT STEPPER=stepper_x CURRENT={HOME_CUR} # Pause to ensure driver stall flag is clear G4 P2000 # Home @@ -339,7 +336,7 @@ gcode: G90 G1 X5 F1200 # Set current during print - SET_TMC_CURRENT STEPPER=stepper_x CURRENT={RUN_CUR} HOLDCURRENT={HOLD_CUR} + SET_TMC_CURRENT STEPPER=stepper_x CURRENT={RUN_CUR} ``` The resulting macro can be called from a @@ -360,7 +357,7 @@ Use the tuning guide described above to find the appropriate "stall sensitivity" for each carriage, but be aware of the following restrictions: 1. When using sensorless homing on CoreXY, make sure there is no - `hold_current` in effect for either stepper during homing. + `hold_current` configured for either stepper. 2. While tuning, make sure both the X and Y carriages are near the center of their rails before each home attempt. 3. After tuning is complete, when homing both X and Y, use macros to