mirror of https://github.com/Desuuuu/klipper.git
config: Add HermitCrab board (#4870)
Signed-off-by: Alan.Ma from BigTreeTech <tech@biqu3d.com>
This commit is contained in:
parent
a1af78cb83
commit
69c0bdefde
|
@ -0,0 +1,65 @@
|
|||
# This file contains common pin mappings for the BIGTREETECH HermitCrab
|
||||
# Canbus board. To use this config, the firmware should be compiled for the
|
||||
# STM32F072 with "8 MHz crystal" and "USB (on PA11/PA12)" or "CAN bus (on PB8/PB9)".
|
||||
# The "HermitCrab" micro-controller will be used to control the components on the nozzle.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[mcu HermitCrab]
|
||||
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
||||
#canbus_uuid: 0e0d81e4210c
|
||||
|
||||
[adxl345]
|
||||
cs_pin: HermitCrab: PB12
|
||||
spi_bus: spi2
|
||||
axes_map: y,z,-x
|
||||
|
||||
[extruder]
|
||||
step_pin: HermitCrab: PA6
|
||||
dir_pin: !HermitCrab: PA7
|
||||
enable_pin: !HermitCrab: PA5
|
||||
microsteps: 16
|
||||
rotation_distance: 33.500
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: HermitCrab: PA2
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: HermitCrab: PA1
|
||||
control: pid
|
||||
pid_Kp: 21.527
|
||||
pid_Ki: 1.063
|
||||
pid_Kd: 108.982
|
||||
min_temp: 0
|
||||
max_temp: 250
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: HermitCrab: PB0
|
||||
run_current: 0.650
|
||||
hold_current: 0.500
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[fan]
|
||||
pin: HermitCrab: PA4
|
||||
|
||||
[heater_fan hotend_fan]
|
||||
pin: HermitCrab: PA3
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
|
||||
[neopixel hotend_rgb]
|
||||
pin: HermitCrab:PA8
|
||||
chain_count: 2
|
||||
color_order: GRB
|
||||
initial_RED: 0.5
|
||||
initial_GREEN: 0.5
|
||||
initial_BLUE: 0.5
|
||||
|
||||
#[bltouch]
|
||||
#sensor_pin: ^HermitCrab:PB2
|
||||
#control_pin: HermitCrab:PB1
|
||||
|
||||
#[filament_switch_sensor switch_sensor]
|
||||
#switch_pin: HermitCrab:PA10
|
||||
|
||||
#[filament_motion_sensor motion_sensor]
|
||||
#switch_pin: ^HermitCrab:PA9
|
Loading…
Reference in New Issue