mirror of https://github.com/Desuuuu/klipper.git
config: Use printer-creality-ender3-s1-2021.cfg for both s1 and s1 pro.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit is contained in:
Kevin O'Connor
parent
282d1113e4
commit
3387a9c23d
|
|
@ -1,9 +1,10 @@
|
|||
# This file contains pin mappings for the stock 2021 Creality Ender 3
|
||||
# S1. To use this config, check the STM32 Chip on the V2.4S1 Board
|
||||
# then during "make menuconfig" select either the STM32F103 with a
|
||||
# "28KiB bootloader" or select the STM32F401 with a "64KiB bootloader"
|
||||
# and serial (on USART1 PA10/PA9) communication for both depending on
|
||||
# the STM32 chip installed on your printer's motherboard.
|
||||
# S1 (and S1 pro). To use this config, check the STM32 Chip on the
|
||||
# V2.4S1 Board then during "make menuconfig" select either the
|
||||
# STM32F103 with a "28KiB bootloader" or select the STM32F401 with a
|
||||
# "64KiB bootloader" and serial (on USART1 PA10/PA9) communication for
|
||||
# both depending on the STM32 chip installed on your printer's
|
||||
# motherboard.
|
||||
|
||||
# If you prefer a direct serial connection, in "make menuconfig"
|
||||
# select "Enable extra low-level configuration options" and select
|
||||
|
|
|
|||
|
|
@ -1,130 +0,0 @@
|
|||
# This file contains pin mappings for the stock 2022 Creality Ender 3
|
||||
# S1 Pro. To use this config, check the STM32 Chip on the V2.4S1 Board
|
||||
# then during "make menuconfig" select either the STM32F103 with a
|
||||
# "28KiB bootloader" or select the STM32F401 with a "64KiB bootloader"
|
||||
# and serial (on USART1 PA10/PA9) communication for both depending on
|
||||
# the STM32 chip installed on your printer's motherboard.
|
||||
|
||||
# If you prefer a direct serial connection, in "make menuconfig"
|
||||
# select "Enable extra low-level configuration options" and select
|
||||
# Serial (on USART2 PA3/PA2), which is broken out on the 10 pin IDC
|
||||
# cable used for the LCD module as follows:
|
||||
# 3: Tx, 4: Rx, 9: GND, 10: VCC
|
||||
|
||||
# Flash this firmware by copying "out/klipper.bin" to a SD card and
|
||||
# turning on the printer with the card inserted. The firmware
|
||||
# filename must changed to "firmware.bin"
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[stepper_x]
|
||||
step_pin: PC2
|
||||
dir_pin: PB9
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: !PA5
|
||||
position_endstop: -10
|
||||
position_max: 235
|
||||
position_min: -15
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_y]
|
||||
step_pin: PB8
|
||||
dir_pin: PB7
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 40
|
||||
endstop_pin: !PA6
|
||||
position_endstop: -10
|
||||
position_max: 241
|
||||
position_min: -15
|
||||
homing_speed: 50
|
||||
|
||||
[stepper_z]
|
||||
step_pin: PB6
|
||||
dir_pin: !PB5
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
rotation_distance: 8
|
||||
endstop_pin: probe:z_virtual_endstop
|
||||
position_max: 270
|
||||
position_min: -4
|
||||
|
||||
[extruder]
|
||||
step_pin: PB4
|
||||
dir_pin: PB3
|
||||
enable_pin: !PC3
|
||||
microsteps: 16
|
||||
gear_ratio: 42:12
|
||||
rotation_distance: 26.359
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.750
|
||||
heater_pin: PA1
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC5
|
||||
control: pid
|
||||
pid_Kp: 23.561
|
||||
pid_Ki: 1.208
|
||||
pid_Kd: 114.859
|
||||
min_temp: 0
|
||||
max_temp: 300
|
||||
|
||||
[heater_bed]
|
||||
heater_pin: PA7
|
||||
sensor_type: EPCOS 100K B57560G104F
|
||||
sensor_pin: PC4
|
||||
control: pid
|
||||
pid_Kp: 71.867
|
||||
pid_Ki: 1.536
|
||||
pid_Kd: 840.843
|
||||
min_temp: 0
|
||||
max_temp: 110
|
||||
|
||||
[heater_fan hotend_fan]
|
||||
pin: PC0
|
||||
|
||||
[fan]
|
||||
pin: PA0
|
||||
|
||||
[mcu]
|
||||
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
||||
restart_method: command
|
||||
|
||||
[printer]
|
||||
kinematics: cartesian
|
||||
max_velocity: 300
|
||||
max_accel: 2000
|
||||
max_z_velocity: 5
|
||||
max_z_accel: 100
|
||||
|
||||
[bltouch]
|
||||
sensor_pin: ^PC14
|
||||
control_pin: PC13
|
||||
x_offset: -31.8
|
||||
y_offset: -40.5
|
||||
z_offset: 0
|
||||
probe_with_touch_mode: true
|
||||
stow_on_each_sample: false
|
||||
|
||||
[bed_mesh]
|
||||
speed: 120
|
||||
mesh_min: 20, 20
|
||||
mesh_max: 200, 200
|
||||
probe_count: 4,4
|
||||
algorithm: bicubic
|
||||
|
||||
[safe_z_home]
|
||||
home_xy_position: 147, 154
|
||||
speed: 75
|
||||
z_hop: 5
|
||||
z_hop_speed: 5
|
||||
move_to_previous: true
|
||||
|
||||
[filament_switch_sensor e0_sensor]
|
||||
switch_pin: !PC15
|
||||
pause_on_runout: true
|
||||
runout_gcode: PAUSE
|
||||
|
||||
[pause_resume]
|
||||
recover_velocity: 25
|
||||
|
|
@ -161,7 +161,6 @@ CONFIG ../../config/printer-creality-cr6se-2020.cfg
|
|||
CONFIG ../../config/printer-creality-cr6se-2021.cfg
|
||||
CONFIG ../../config/printer-creality-ender2pro-2021.cfg
|
||||
CONFIG ../../config/printer-creality-ender3-s1-2021.cfg
|
||||
CONFIG ../../config/printer-creality-ender3-s1pro-2022.cfg
|
||||
CONFIG ../../config/printer-creality-ender3-v2-2020.cfg
|
||||
CONFIG ../../config/printer-creality-ender3max-2021.cfg
|
||||
CONFIG ../../config/printer-creality-ender3pro-2020.cfg
|
||||
|
|
|
|||
Loading…
Reference in New Issue