2020-02-14 02:52:31 +01:00
|
|
|
# This file contains pin mappings for the Wanhao Duplicator 9 MK1,
|
|
|
|
|
# also sold as the Monoprice Maker Pro MK1. To use this config,
|
|
|
|
|
# the firmware should be compiled for the AVR atmega2560.
|
|
|
|
|
|
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: ar61
|
|
|
|
|
dir_pin: !ar62
|
|
|
|
|
enable_pin: !ar60
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^!ar54
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 295
|
|
|
|
|
homing_speed: 30.0
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: ar64
|
|
|
|
|
dir_pin: ar65
|
|
|
|
|
enable_pin: !ar2
|
|
|
|
|
step_distance: .0125
|
|
|
|
|
endstop_pin: ^!ar24
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 290
|
|
|
|
|
homing_speed: 30.0
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: ar67
|
|
|
|
|
dir_pin: ar69
|
|
|
|
|
enable_pin: !ar66
|
|
|
|
|
step_distance: .0025
|
|
|
|
|
endstop_pin: probe:z_virtual_endstop
|
|
|
|
|
position_endstop: 1.4
|
|
|
|
|
position_max: 370
|
|
|
|
|
position_min: -0.99
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: ar58
|
|
|
|
|
dir_pin: ar59
|
|
|
|
|
enable_pin: !ar57
|
|
|
|
|
step_distance: .009980
|
|
|
|
|
nozzle_diameter: 0.4
|
|
|
|
|
filament_diameter: 1.75
|
|
|
|
|
heater_pin: ar4
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: analog1
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 33.41
|
|
|
|
|
pid_Ki: 1.47
|
|
|
|
|
pid_Kd: 189.27
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 315
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: ar3
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: analog14
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 64.095903
|
|
|
|
|
pid_Ki: 1.649830
|
|
|
|
|
pid_Kd: 622.531455
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 120
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: ar5
|
|
|
|
|
|
|
|
|
|
[probe]
|
|
|
|
|
pin: !ar6
|
|
|
|
|
x_offset: 27
|
|
|
|
|
y_offset: 3
|
|
|
|
|
z_offset: 1.4
|
|
|
|
|
speed: 5.0
|
|
|
|
|
samples: 2
|
|
|
|
|
sample_retract_dist: 2.0
|
|
|
|
|
samples_result: average
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/ttyUSB0
|
|
|
|
|
pin_map: arduino
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 3000
|
|
|
|
|
max_accel: 450
|
|
|
|
|
max_z_velocity: 225
|
|
|
|
|
max_z_accel: 30
|
|
|
|
|
square_corner_velocity: 15.0
|
|
|
|
|
|
|
|
|
|
[bed_mesh]
|
|
|
|
|
speed: 120
|
2020-02-18 02:59:08 +01:00
|
|
|
mesh_min: 27,3
|
2020-02-14 02:52:31 +01:00
|
|
|
mesh_max: 270,290
|
|
|
|
|
probe_count: 5,3
|
|
|
|
|
horizontal_move_z: 10
|
|
|
|
|
|
|
|
|
|
[bed_screws]
|
|
|
|
|
screw1: 5,5
|
|
|
|
|
screw1_name: front left screw
|
|
|
|
|
screw2: 295,0
|
|
|
|
|
screw2_name: front right screw
|
|
|
|
|
screw3: 295,290
|
|
|
|
|
screw3_name: back right screw
|
|
|
|
|
screw4: 0,290
|
|
|
|
|
screw4_name: back left screw
|
|
|
|
|
probe_height: 0
|
