klipper-dgus/docs/Config_Changes.md

This document covers recent software changes to the config file that
are not backwards compatible. It is a good idea to review this
document when upgrading the Klipper software.

All dates in this document are approximate.

# Changes

20201020: Klipper v0.9.0 released.

20200902: The RTD resistance-to-temperature calculation for MAX31865
converters has been corrected to not read low.  If you are using such a
device, you should recalibrate your print temperature and PID settings.

20200816: The gcode macro `printer.gcode` object has been renamed to
`printer.gcode_move`.  Several undocumented variables in
`printer.toolhead` and `printer.gcode` have been removed.  See
docs/Command_Templates.md for a list of available template variables.

20200816: The gcode macro "action_" system has changed.  Replace any
calls to `printer.gcode.action_emergency_stop()` with
`action_emergency_stop()`, `printer.gcode.action_respond_info()` with
`action_respond_info()`, and `printer.gcode.action_respond_error()`
with `action_raise_error()`.

20200809: The menu system has been rewritten. If the menu has been
customized then it will be necessary to update to the new
configuration. See config/example-menu.cfg for configuration details
and see klippy/extras/display/menu.cfg for examples.

20200731:  The behavior of the `progress` attribute reported by
the `virtual_sdcard` printer object has changed.  Progress is no
longer reset to 0 when a print is paused.  It will now always report
progress based on the internal file position, or 0 if no file is
currently loaded.

20200725: The servo `enable` config parameter and the SET_SERVO
`ENABLE` parameter have been removed.  Update any macros to use
`SET_SERVO SERVO=my_servo WIDTH=0` to disable a servo.

20200608: The LCD display support has changed the name of some
internal "glyphs".  If a custom display layout was implemented it may
be necessary to update to the latest glyph names (see
klippy/extras/display/display.cfg for a list of available glyphs).

20200606: The pin names on linux mcu have changed. Pins now have names
of the form `gpiochip<chipid>/gpio<gpio>`.  For gpiochip0 you can also
use a short `gpio<gpio>`.  For example, what was previously referred
to as `P20` now becomes `gpio20` or `gpiochip0/gpio20`.

20200603: The default 16x4 LCD layout will no longer show the
estimated time remaining in a print.  (Only the elapsed time will be
shown.)  If the old behavior is desired one can customize the menu
display with that information (see the description of display_data in
config/example-extras.cfg for details).

20200531: The default USB vendor/product id is now 0x1d50/0x614e.
These new ids are reserved for Klipper (thanks to the openmoko
project). This change should not require any config changes, but the
new ids may appear in system logs.

20200524: The default value for the tmc5160 pwm_freq field is now zero
(instead of one).

20200425: The gcode_macro command template variable `printer.heater`
was renamed to `printer.heaters`.

20200313: The default lcd layout for multi-extruder printers with a
16x4 screen has changed.  The single extruder screen layout is now the
default and it will show the currently active extruder.  To use the
previous display layout set "display_group: _multiextruder_16x4" in
the [display] section of the printer.cfg file.

20200308: The default `__test` menu item was removed. If the config
file has a custom menu then be sure to remove all references to this
`__test` menu item.

20200308: The menu "deck" and "card" options were removed. To
customize the layout of an lcd screen use the new display_data config
sections (see config/example-extras.cfg for the details).

20200109:  The bed_mesh module now references the probe's location
in for the mesh configuration.  As such, some configuration options
have been renamed to more accurately reflect their intended
functionality.  For rectangular beds, `min_point` and `max_point`
have been renamed to `mesh_min` and `mesh_max` respectively.  For
round beds, `bed_radius` has been renamed to `mesh_radius`.  A new
`mesh_origin` option has also been added for round beds.  Note that
these changes are also incompatible with previously saved mesh profiles.
If an incompatible profile is detected it will be ignored and scheduled
for removal.  The removal process can be completed by issuing the
SAVE_CONFIG command. The user will need to re-calibrate each profile.

20191218: The display config section no longer supports "lcd_type:
st7567".  Use the "uc1701" display type instead - set "lcd_type:
uc1701" and change the "rs_pin: some_pin" to "rst_pin: some_pin".  It
may also be necessary to add a "contrast: 60" config setting.

20191210: The builtin T0, T1, T2, ... commands have been removed.  The
extruder activate_gcode and deactivate_gcode config options have been
removed.  If these commands (and scripts) are needed then define
individual [gcode_macro T0] style macros that call the
ACTIVATE_EXTRUDER command.  See the config/sample-idex.cfg and
sample-multi-extruder.cfg files for examples.

20191210: Support for the M206 command has been removed.  Replace with
calls to SET_GCODE_OFFSET.  If support for M206 is needed, add a
[gcode_macro M206] config section that calls SET_GCODE_OFFSET.  (For
example "SET_GCODE_OFFSET Z=-{params.Z}".)

20191202: Support for the undocumented "S" parameter of the "G4"
command has been removed.  Replace any occurrences of S with the
standard "P" parameter (the delay specified in milliseconds).

20191126: The USB names have changed on micro-controllers with native
USB support.  They now use a unique chip id by default (where
available).  If an "mcu" config section uses a "serial" setting that
starts with "/dev/serial/by-id/" then it may be necessary to update
the config.  Run "ls /dev/serial/by-id/*" in an ssh terminal to
determine the new id.

20191121: The pressure_advance_lookahead_time parameter has been
removed.  See example.cfg for alternate configuration settings.

20191112: The tmc stepper driver virtual enable capability is now
automatically enabled if the stepper does not have a dedicated stepper
enable pin.  Remove references to tmcXXXX:virtual_enable from the
config.  The ability to control multiple pins in the stepper
enable_pin config has been removed.  If multiple pins are needed then
use a multi_pin config section.

20191107: The primary extruder config section must be specified as
"extruder" and may no longer be specified as "extruder0". Gcode
command templates that query the extruder status are now accessed via
"{printer.extruder}".

20191021: Klipper v0.8.0 released

20191003: The move_to_previous option in [safe_z_homing] now defaults
to False.  (It was effectively False prior to 20190918.)

20190918: The zhop option in [safe_z_homing] is always re-applied
after Z axis homing completed. This might need users to update custom
scripts based on this module.

20190806: The SET_NEOPIXEL command has been renamed to SET_LED.

20190726: The mcp4728 digital-to-analog code has changed. The default
i2c_address is now 0x60 and the voltage reference is now relative to
the mcp4728's internal 2.048 volt reference.

20190710: The z_hop option was removed from the [firmware_retract]
config section. The z_hop support was incomplete and could cause
incorrect behavior with several common slicers.

20190710: The optional parameters of the PROBE_ACCURACY command have
changed. It may be necessary to update any macros or scripts that use
that command.

20190628: All configuration options have been removed from the
[skew_correction] section.  Configuration for skew_correction
is now done via the SET_SKEW gcode.  See skew_correction.md
for recommended usage.

20190607: The "variable_X" parameters of gcode_macro (along with the
VALUE parameter of SET_GCODE_VARIABLE) are now parsed as Python
literals. If a value needs to be assigned a string then wrap the value
in quotes so that it is evaluated as a string.

20190606: The "samples", "samples_result", and "sample_retract_dist"
config options have been moved to the "probe" config section. These
options are no longer supported in the "delta_calibrate", "bed_tilt",
"bed_mesh", "screws_tilt_adjust", "z_tilt", or "quad_gantry_level"
config sections.

20190528: The magic "status" variable in gcode_macro template
evaluation has been renamed to "printer".

20190520: The SET_GCODE_OFFSET command has changed; update any g-code
macros accordingly. The command will no longer apply the requested
offset to the next G1 command. The old behavior may be approximated by
using the new "MOVE=1" parameter.

20190404: The Python host software packages were updated. Users will
need to rerun the ~/klipper/scripts/install-octopi.sh script (or
otherwise upgrade the python dependencies if not using a standard
OctoPi installation).

20190404: The i2c_bus and spi_bus parameters (in various config
sections) now take a bus name instead of a number.

20190404: The sx1509 config parameters have changed. The 'address'
parameter is now 'i2c_address' and it must be specified as a decimal
number. Where 0x3E was previously used, specify 62.

20190328: The min_speed value in [temperature_fan] config
will now be respected and the fan will always run at this
speed or higher in PID mode.

20190322: The default value for "driver_HEND" in [tmc2660] config
sections was changed from 6 to 3. The "driver_VSENSE" field was
removed (it is now automatically calculated from run_current).

20190310: The [controller_fan] config section now always takes a name
(such as [controller_fan my_controller_fan]).

20190308: The "driver_BLANK_TIME_SELECT" field in [tmc2130] and
[tmc2208] config sections has been renamed to "driver_TBL".

20190308: The [tmc2660] config section has changed. A new
sense_resistor config parameter must now be provided. The meaning of
several of the driver_XXX parameters has changed.

20190228: Users of SPI or I2C on SAMD21 boards must now specify the
bus pins via a [samd_sercom] config section.

20190224: The bed_shape option has been removed from bed_mesh.  The
radius option has been renamed to bed_radius.  Users with round beds
should supply the bed_radius and round_probe_count options.

20190107: The i2c_address parameter in the mcp4451 config section
changed. This is a common setting on Smoothieboards. The new value is
half the old value (88 should be changed to 44, and 90 should be
changed to 45).

20181220: Klipper v0.7.0 released