2022-07-22 03:45:05 +02:00
|
|
|
# This file contains pin mappings for the Creality Sermoon V1
|
|
|
|
|
# with CR-FDM-v2.4.S1.200 motherboard.
|
|
|
|
|
|
|
|
|
|
# To use this config, during "make menuconfig" select the STM32F401
|
2022-07-22 03:56:46 +02:00
|
|
|
# with a "64KiB bootloader" and serial (on USART1 PA10/PA9)
|
|
|
|
|
# communication.
|
2022-07-22 03:45:05 +02:00
|
|
|
|
|
|
|
|
# If you prefer a direct serial connection, in "make menuconfig"
|
|
|
|
|
# select "Enable extra low-level configuration options" and select
|
|
|
|
|
# Serial (on USART2 PA3/PA2), which is broken out on the 10 pin IDC
|
|
|
|
|
# cable used for the LCD module as follows:
|
|
|
|
|
# 3: Tx, 4: Rx, 9: GND, 10: VCC
|
|
|
|
|
|
|
|
|
|
# Flash this firmware by copying "out/klipper.bin" to a SD card and
|
|
|
|
|
# turning on the printer with the card inserted. The firmware
|
|
|
|
|
# filename must changed to "firmware.bin"
|
|
|
|
|
|
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: PA7
|
|
|
|
|
dir_pin: !PA4
|
|
|
|
|
enable_pin: !PB8
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 40
|
|
|
|
|
endstop_pin: PC4
|
|
|
|
|
position_endstop: 175
|
|
|
|
|
position_max: 175
|
|
|
|
|
position_min: 0
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: PB0
|
|
|
|
|
dir_pin: PB10
|
|
|
|
|
enable_pin: !PB8
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 40
|
|
|
|
|
endstop_pin: PB13
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 175
|
|
|
|
|
position_min: 0
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: PB7
|
|
|
|
|
dir_pin: PB6
|
|
|
|
|
enable_pin: !PB8
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 8
|
|
|
|
|
endstop_pin: PB3
|
|
|
|
|
position_endstop: 165
|
|
|
|
|
position_max: 168
|
|
|
|
|
position_min: -3
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: PB1
|
|
|
|
|
dir_pin: PB12
|
|
|
|
|
enable_pin: !PB8
|
|
|
|
|
microsteps: 16
|
|
|
|
|
gear_ratio: 42:12
|
|
|
|
|
rotation_distance: 26.359
|
|
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: PC5
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PC1
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 30.090
|
|
|
|
|
pid_Ki: 1.875
|
|
|
|
|
pid_Kd: 120.735
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 290
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: PB9
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PC0
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 75.694
|
|
|
|
|
pid_Ki: 1.160
|
|
|
|
|
pid_Kd: 1234.759
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 90
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: PA5
|
|
|
|
|
|
|
|
|
|
[fan_generic side_fan]
|
|
|
|
|
pin: PC15
|
|
|
|
|
|
|
|
|
|
# [controller_fan controller_fan]
|
|
|
|
|
# In order to access the controller fan, the controller fan needs to be plugged
|
|
|
|
|
# in another location. See https://github.com/Klipper3d/klipper/pull/5621
|
|
|
|
|
# for more information.
|
|
|
|
|
# pin: PB4
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
|
|
|
|
restart_method: command
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 2000
|
|
|
|
|
max_z_velocity: 5
|
|
|
|
|
max_z_accel: 100
|
|
|
|
|
|
|
|
|
|
[pause_resume]
|
|
|
|
|
recover_velocity: 25
|
