2021-02-03 00:14:11 +01:00
|
|
|
# This file contains pin mappings for the stock 2020 Creality Ender 3
|
|
|
|
|
# MAX. To use this config, during "make menuconfig" select the
|
2021-03-18 18:20:54 +01:00
|
|
|
# STM32F103 with a "28KiB bootloader" and serial (on USART1 PA10/PA9)
|
|
|
|
|
# communication.
|
2021-02-03 00:14:11 +01:00
|
|
|
|
|
|
|
|
# Because this printer has factory wiring, mounts, and firmware for
|
|
|
|
|
# a BLTouch, but does not ship with one at this time, default values
|
|
|
|
|
# for the sensor have been specified, but disabled, in anticipation of
|
|
|
|
|
# future revisions or user modification. User should take care to
|
|
|
|
|
# customize the offsets, particularly z-offset, for their specific unit.
|
|
|
|
|
|
|
|
|
|
# If you prefer a direct serial connection, in "make menuconfig"
|
2021-03-18 18:20:54 +01:00
|
|
|
# select "Enable extra low-level configuration options" and select
|
|
|
|
|
# serial (on USART3 PB11/PB10), which is broken out on the 10 pin IDC
|
|
|
|
|
# cable used for the LCD module as follows:
|
2021-02-03 00:14:11 +01:00
|
|
|
# 3: Tx, 4: Rx, 9: GND, 10: VCC
|
|
|
|
|
|
|
|
|
|
# Flash this firmware by copying "out/klipper.bin" to a SD card and
|
|
|
|
|
# turning on the printer with the card inserted. The firmware
|
|
|
|
|
# filename must end in ".bin" and must not match the last filename
|
|
|
|
|
# that was flashed.
|
|
|
|
|
|
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: PC2
|
|
|
|
|
dir_pin: PB9
|
|
|
|
|
enable_pin: !PC3
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 40
|
|
|
|
|
endstop_pin: ^PA5
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 300
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: PB8
|
|
|
|
|
dir_pin: PB7
|
|
|
|
|
enable_pin: !PC3
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 40
|
|
|
|
|
endstop_pin: ^PA6
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 300
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: PB6
|
|
|
|
|
dir_pin: !PB5
|
|
|
|
|
enable_pin: !PC3
|
|
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 8
|
|
|
|
|
position_endstop: 0.0 # disable to use BLTouch
|
|
|
|
|
endstop_pin: ^PA7 # disable to use BLTouch
|
|
|
|
|
#endstop_pin: probe:z_virtual_endstop # enable to use BLTouch
|
|
|
|
|
#position_min: -5 # enable to use BLTouch
|
|
|
|
|
position_max: 340
|
|
|
|
|
|
|
|
|
|
# [safe_z_home] # enable for BLTouch
|
|
|
|
|
# home_xy_position: 150, 150
|
|
|
|
|
# speed: 100
|
|
|
|
|
# z_hop: 10
|
|
|
|
|
# z_hop_speed: 5
|
|
|
|
|
|
|
|
|
|
# [bltouch] # enable for BLTouch - fast-mode
|
|
|
|
|
# sensor_pin: ^PB1
|
|
|
|
|
# control_pin: PB0
|
|
|
|
|
# pin_up_touch_mode_reports_triggered: True
|
|
|
|
|
# probe_with_touch_mode: True
|
|
|
|
|
# x_offset: 50 # modify as needed for bltouch location
|
|
|
|
|
# y_offset: -6 # modify as needed for bltouch location
|
|
|
|
|
# z_offset: 0.0 # modify as needed for bltouch or run PROBE_CALIBRATE
|
|
|
|
|
# speed: 10
|
|
|
|
|
# samples: 3
|
|
|
|
|
# sample_retract_dist: 5.0 # Can be set lower, example 2.5 depending on height of bltouch from bed
|
|
|
|
|
# lift_speed: 40
|
|
|
|
|
# samples_tolerance_retries: 3
|
|
|
|
|
# speed: 10
|
|
|
|
|
# samples: 2
|
|
|
|
|
|
|
|
|
|
# [bed_mesh] # enable for BLTouch
|
|
|
|
|
# speed: 300
|
|
|
|
|
# mesh_min: 50, 0
|
|
|
|
|
# mesh_max: 290, 290
|
|
|
|
|
# algorithm: bicubic
|
|
|
|
|
# probe_count: 7,7 # 49 points due to large bed size
|
|
|
|
|
# horizontal_move_z: 5
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
# [gcode_macro G29] # If moving from marlin to klipper uncomment to mimic G29
|
|
|
|
|
# gcode:
|
|
|
|
|
# BED_MESH_CALIBRATE
|
|
|
|
|
# G1 X0 Y0 Z10 F4000
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
max_extrude_only_distance: 100.0
|
|
|
|
|
step_pin: PB4
|
|
|
|
|
dir_pin: PB3
|
|
|
|
|
enable_pin: !PC3
|
|
|
|
|
microsteps: 16
|
2021-09-24 01:45:22 +02:00
|
|
|
rotation_distance: 31.901 # Calibrate - see https://www.klipper3d.org/Rotation_Distance.html
|
2021-02-03 00:14:11 +01:00
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: PA1
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PC5
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 21.527
|
|
|
|
|
pid_Ki: 1.063
|
|
|
|
|
pid_Kd: 108.982
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 250
|
2021-09-24 01:45:22 +02:00
|
|
|
pressure_advance: 0.0 # Calibrate - see https://www.klipper3d.org/Pressure_Advance.html
|
2021-02-03 00:14:11 +01:00
|
|
|
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: PA2
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PC4
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 54.027
|
|
|
|
|
pid_Ki: 0.770
|
|
|
|
|
pid_Kd: 948.182
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 130
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: PA0
|
|
|
|
|
|
|
|
|
|
[filament_switch_sensor e0_sensor]
|
|
|
|
|
switch_pin: PA4
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0 # Run ls /dev/serial/by-id/* for micro-controller name
|
|
|
|
|
restart_method: command
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 3000
|
|
|
|
|
max_z_velocity: 5
|
|
|
|
|
max_z_accel: 100
|
|
|
|
|
|
|
|
|
|
[display]
|
|
|
|
|
lcd_type: st7920
|
|
|
|
|
cs_pin: PB12
|
|
|
|
|
sclk_pin: PB13
|
|
|
|
|
sid_pin: PB15
|
2021-08-20 04:18:24 +02:00
|
|
|
encoder_pins: ^PB14, ^PB10
|
|
|
|
|
click_pin: ^!PB2
|
