2018-01-08 12:56:22 +01:00
|
|
|
# This file contains common pin mappings for the 2017 Creality
|
|
|
|
|
# CR-10. To use this config, the firmware should be compiled for the
|
|
|
|
|
# AVR atmega1284p.
|
|
|
|
|
|
2018-11-13 20:32:52 +01:00
|
|
|
# Note, a number of Melzi boards are shipped with a bootloader that
|
|
|
|
|
# requires the following command to flash the board:
|
|
|
|
|
# avrdude -p atmega1284p -c arduino -b 57600 -P /dev/ttyUSB0 -U out/klipper.elf.hex
|
|
|
|
|
# If the above command does not work and "make flash" does not work
|
|
|
|
|
# then one may need to flash a bootloader to the board - see the
|
|
|
|
|
# Klipper docs/Bootloaders.md file for more information.
|
2018-01-08 12:56:22 +01:00
|
|
|
|
2020-11-17 00:47:32 +01:00
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
2018-01-08 12:56:22 +01:00
|
|
|
|
|
|
|
|
[stepper_x]
|
|
|
|
|
step_pin: PD7
|
|
|
|
|
dir_pin: !PC5
|
|
|
|
|
enable_pin: !PD6
|
2020-12-14 15:09:19 +01:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 40
|
2018-01-08 12:56:22 +01:00
|
|
|
endstop_pin: ^PC2
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 300
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_y]
|
|
|
|
|
step_pin: PC6
|
|
|
|
|
dir_pin: !PC7
|
|
|
|
|
enable_pin: !PD6
|
2020-12-14 15:09:19 +01:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 40
|
2018-01-08 12:56:22 +01:00
|
|
|
endstop_pin: ^PC3
|
|
|
|
|
position_endstop: 0
|
|
|
|
|
position_max: 300
|
|
|
|
|
homing_speed: 50
|
|
|
|
|
|
|
|
|
|
[stepper_z]
|
|
|
|
|
step_pin: PB3
|
|
|
|
|
dir_pin: PB2
|
|
|
|
|
enable_pin: !PA5
|
2020-12-14 15:09:19 +01:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 8
|
2018-01-08 12:56:22 +01:00
|
|
|
endstop_pin: ^PC4
|
|
|
|
|
position_endstop: 0.0
|
|
|
|
|
position_max: 400
|
|
|
|
|
|
|
|
|
|
[extruder]
|
|
|
|
|
step_pin: PB1
|
|
|
|
|
dir_pin: !PB0
|
|
|
|
|
enable_pin: !PD6
|
2020-12-14 15:09:19 +01:00
|
|
|
microsteps: 16
|
|
|
|
|
rotation_distance: 33.683
|
2018-01-08 12:56:22 +01:00
|
|
|
nozzle_diameter: 0.400
|
|
|
|
|
filament_diameter: 1.750
|
|
|
|
|
heater_pin: PD5
|
|
|
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
|
|
|
sensor_pin: PA7
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 22.57
|
|
|
|
|
pid_Ki: 1.72
|
|
|
|
|
pid_Kd: 73.96
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 250
|
|
|
|
|
|
|
|
|
|
[heater_bed]
|
|
|
|
|
heater_pin: PD4
|
2019-02-08 18:20:16 +01:00
|
|
|
sensor_type: ATC Semitec 104GT-2
|
2018-01-08 12:56:22 +01:00
|
|
|
sensor_pin: PA6
|
|
|
|
|
control: pid
|
|
|
|
|
pid_Kp: 426.68
|
|
|
|
|
pid_Ki: 78.92
|
|
|
|
|
pid_Kd: 576.71
|
|
|
|
|
min_temp: 0
|
|
|
|
|
max_temp: 130
|
|
|
|
|
|
|
|
|
|
[fan]
|
|
|
|
|
pin: PB4
|
|
|
|
|
|
|
|
|
|
[mcu]
|
|
|
|
|
serial: /dev/ttyUSB0
|
|
|
|
|
|
|
|
|
|
[printer]
|
|
|
|
|
kinematics: cartesian
|
|
|
|
|
max_velocity: 300
|
|
|
|
|
max_accel: 3000
|
|
|
|
|
max_z_velocity: 5
|
|
|
|
|
max_z_accel: 100
|
2018-03-07 19:36:44 +01:00
|
|
|
|
|
|
|
|
[display]
|
|
|
|
|
lcd_type: st7920
|
|
|
|
|
cs_pin: PA3
|
|
|
|
|
sclk_pin: PA1
|
|
|
|
|
sid_pin: PC1
|
2018-09-02 17:52:20 +02:00
|
|
|
encoder_pins: ^PD2, ^PD3
|
|
|
|
|
click_pin: ^!PC0
|
