mirror of https://github.com/Desuuuu/klipper.git
158 lines
3.1 KiB
INI
158 lines
3.1 KiB
INI
|
# This file contains common pin mappings for the Mellow Fly-Gemini-v1.
|
||
|
|
# To use this config, the firmware should be compiled for the
|
||
|
|
# STM32F405 with a "32KiB bootloader".
|
||
|
|
|
||
|
|
# The "make flash" command does not work on the Fly-Gemini-v1. Instead,
|
||
|
|
# after running "make", copy the generated "out/klipper.bin" file to a
|
||
|
|
# file named "firmware.bin" or "klipper.bin" on an SD card and then restart the Fly-Gemini-v1
|
||
|
|
# with that SD card.
|
||
|
|
|
||
|
|
# See docs/Config_Reference.md for a description of parameters.
|
||
|
|
|
||
|
|
[stepper_x]
|
||
|
|
step_pin: PC13
|
||
|
|
dir_pin: PC1
|
||
|
|
enable_pin: !PB2
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 40
|
||
|
|
endstop_pin: ^PA3
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 200
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
step_pin: PC14
|
||
|
|
dir_pin: !PC4
|
||
|
|
enable_pin: !PB6
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 40
|
||
|
|
endstop_pin: ^PB1
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 200
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
step_pin: PC15
|
||
|
|
dir_pin: PC5
|
||
|
|
enable_pin: !PB5
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 40
|
||
|
|
endstop_pin: ^PB10
|
||
|
|
position_endstop: 0.5
|
||
|
|
position_max: 200
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
step_pin: PC3
|
||
|
|
dir_pin: PC7
|
||
|
|
enable_pin: !PB4
|
||
|
|
microsteps: 16
|
||
|
|
rotation_distance: 33.500
|
||
|
|
nozzle_diameter: 0.400
|
||
|
|
filament_diameter: 1.750
|
||
|
|
heater_pin: PA0
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: PC0
|
||
|
|
control: pid
|
||
|
|
pid_Kp: 22.2
|
||
|
|
pid_Ki: 1.08
|
||
|
|
pid_Kd: 114
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 250
|
||
|
|
|
||
|
|
[heater_bed]
|
||
|
|
heater_pin: PA2
|
||
|
|
sensor_type: Generic 3950
|
||
|
|
sensor_pin: PC2
|
||
|
|
control: watermark
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 130
|
||
|
|
|
||
|
|
[fan]
|
||
|
|
pin: PC6
|
||
|
|
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: cartesian
|
||
|
|
max_velocity: 300
|
||
|
|
max_accel: 3000
|
||
|
|
max_z_velocity: 5
|
||
|
|
max_z_accel: 100
|
||
|
|
|
||
|
|
|
||
|
|
########################################
|
||
|
|
# TMC2209 configuration
|
||
|
|
########################################
|
||
|
|
|
||
|
|
#[tmc2209 stepper_x]
|
||
|
|
#uart_pin: PB11
|
||
|
|
#run_current: 0.800
|
||
|
|
#diag_pin: PA3
|
||
|
|
#stealthchop_threshold: 999999
|
||
|
|
|
||
|
|
#[tmc2209 stepper_y]
|
||
|
|
#uart_pin: PB9
|
||
|
|
#run_current: 0.800
|
||
|
|
#diag_pin: PB1
|
||
|
|
#stealthchop_threshold: 999999
|
||
|
|
|
||
|
|
#[tmc2209 stepper_z]
|
||
|
|
#uart_pin: PB8
|
||
|
|
#run_current: 0.800
|
||
|
|
#diag_pin: PB10
|
||
|
|
#stealthchop_threshold: 999999
|
||
|
|
|
||
|
|
#[tmc2209 extruder]
|
||
|
|
#uart_pin: PB7
|
||
|
|
#run_current: 0.600
|
||
|
|
#diag_pin:
|
||
|
|
#stealthchop_threshold: 999999
|
||
|
|
|
||
|
|
########################################
|
||
|
|
# TMC5160 configuration
|
||
|
|
########################################
|
||
|
|
|
||
|
|
#[tmc5160 stepper_x]
|
||
|
|
#cs_pin: PB11
|
||
|
|
#spi_bus: spi1
|
||
|
|
#run_current: 0.800
|
||
|
|
#diag1_pin: PA3
|
||
|
|
#stealthchop_threshold: 999999
|
||
|
|
|
||
|
|
#[tmc5160 stepper_y]
|
||
|
|
#cs_pin: PB9
|
||
|
|
#spi_bus: spi1
|
||
|
|
#run_current: 0.800
|
||
|
|
#diag1_pin: PB1
|
||
|
|
#stealthchop_threshold: 999999
|
||
|
|
|
||
|
|
#[tmc5160 stepper_z]
|
||
|
|
#cs_pin: PB8
|
||
|
|
#spi_bus: spi1
|
||
|
|
#run_current: 0.800
|
||
|
|
#diag1_pin: PB10
|
||
|
|
#stealthchop_threshold: 999999
|
||
|
|
|
||
|
|
#[tmc5160 extruder]
|
||
|
|
#cs_pin: PB7
|
||
|
|
#spi_bus: spi1
|
||
|
|
#run_current: 0.800
|
||
|
|
#diag1_pin:
|
||
|
|
#stealthchop_threshold: 999999
|
||
|
|
|
||
|
|
########################################
|
||
|
|
# EXP1 / EXP2 (display) pins
|
||
|
|
########################################
|
||
|
|
|
||
|
|
[board_pins]
|
||
|
|
aliases:
|
||
|
|
# EXP1 header
|
||
|
|
EXP1_1=<NC>, EXP1_3=PA13, EXP1_5=PA9, EXP1_7=<NC>, EXP1_9=<GND>,
|
||
|
|
EXP1_2=PA4, EXP1_4=PA10, EXP1_6=PA8, EXP1_8=<NC>, EXP1_10=<5V>,
|
||
|
|
# EXP2 header
|
||
|
|
EXP2_1=PB14, EXP2_3=PA15, EXP2_5=PA14, EXP2_7=PB3, EXP2_9=<GND>,
|
||
|
|
EXP2_2=PB13, EXP2_4=PB12, EXP2_6=PB15, EXP2_8=<RST>, EXP2_10=<NC>,
|
||
|
|
|
||
|
|
# See the sample-lcd.cfg file for definitions of common LCD displays.
|