mirror of https://github.com/Desuuuu/klipper.git
136 lines
2.4 KiB
INI
136 lines
2.4 KiB
INI
|
# This file contains common pin mappings for Alligator (Rev.3) board.
|
||
|
|
# To use this config, the firmware should be compiled for the Arduino
|
||
|
|
# Due.
|
||
|
|
|
||
|
|
# Remember flash procedure:
|
||
|
|
# sudo /etc/init.d/alligator-manager --erase
|
||
|
|
# sudo bossac -e -w -v -b -R -i -p ttyAMA0 klipper.bin
|
||
|
|
# See alligator github for alligator manager:
|
||
|
|
# https://github.com/3Dartists/alligator-manager
|
||
|
|
|
||
|
|
# See docs/Config_Reference.md for a description of parameters.
|
||
|
|
|
||
|
|
[static_digital_output DRV8825_microstepping]
|
||
|
|
pins:PC10
|
||
|
|
pins:PC29
|
||
|
|
pins:PC19
|
||
|
|
pins:PC18
|
||
|
|
|
||
|
|
[dac084S085 stepper_digipot]
|
||
|
|
enable_pin: PD2
|
||
|
|
spi_bus: spi0
|
||
|
|
# Scale the config so that the channel value can be specified in amps.
|
||
|
|
# (For Alligator v3.0 boards, use 2.50)
|
||
|
|
scale: 2.50
|
||
|
|
# Channel A in this example is X, B is Y, C is Z, D is E0,1,2,3.
|
||
|
|
channel_A: 1.5
|
||
|
|
channel_B: 1.5
|
||
|
|
channel_C: 1.5
|
||
|
|
channel_D: 1.0
|
||
|
|
# channel D will be the current used by all extruders if> 1
|
||
|
|
|
||
|
|
[stepper_x]
|
||
|
|
step_pin: PB24
|
||
|
|
dir_pin: !PB25
|
||
|
|
enable_pin: !PA15
|
||
|
|
microsteps: 32 # number of microstep 16, 32
|
||
|
|
rotation_distance: 16
|
||
|
|
endstop_pin: ^!PC5
|
||
|
|
position_endstop: -30
|
||
|
|
position_max: 220
|
||
|
|
position_min: -30
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_y]
|
||
|
|
step_pin: PB22
|
||
|
|
dir_pin: !PB23
|
||
|
|
enable_pin: !PC28
|
||
|
|
microsteps: 32
|
||
|
|
rotation_distance: 16
|
||
|
|
endstop_pin: ^!PC3
|
||
|
|
position_endstop: -8
|
||
|
|
position_min: -8
|
||
|
|
position_max: 220
|
||
|
|
homing_speed: 50
|
||
|
|
|
||
|
|
[stepper_z]
|
||
|
|
step_pin: PB20
|
||
|
|
dir_pin: PB21
|
||
|
|
enable_pin: !PA29
|
||
|
|
microsteps: 32
|
||
|
|
rotation_distance: 4
|
||
|
|
endstop_pin: ^!PC2
|
||
|
|
position_endstop: 0
|
||
|
|
position_max: 240
|
||
|
|
position_min: -1
|
||
|
|
|
||
|
|
[extruder]
|
||
|
|
step_pin: PB18
|
||
|
|
dir_pin: PB19
|
||
|
|
enable_pin: !PC27
|
||
|
|
microsteps: 32
|
||
|
|
rotation_distance: 7
|
||
|
|
nozzle_diameter: 0.400
|
||
|
|
filament_diameter: 1.750
|
||
|
|
heater_pin: PA19
|
||
|
|
sensor_pin: PC25
|
||
|
|
sensor_type: ATC Semitec 104NT-4-R025H42G
|
||
|
|
control: pid
|
||
|
|
pid_kp: 15.572
|
||
|
|
pid_ki: 0.446
|
||
|
|
pid_kd: 136.064
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 270
|
||
|
|
|
||
|
|
#[extruder1]
|
||
|
|
#step_pin: PB17
|
||
|
|
#dir_pin: !PB14
|
||
|
|
#enable_pin: !PD6
|
||
|
|
#microsteps: 32
|
||
|
|
#heater_pin: PC22
|
||
|
|
#sensor_pin: PA29
|
||
|
|
|
||
|
|
#[extruder2]
|
||
|
|
#step_pin: PB12
|
||
|
|
#dir_pin: !PB13
|
||
|
|
#enable_pin: !PD8
|
||
|
|
#microsteps: 32
|
||
|
|
#heater_pin: PC21
|
||
|
|
#sensor_pin: PC28
|
||
|
|
|
||
|
|
#[extruder3]
|
||
|
|
#step_pin: PB15
|
||
|
|
#dir_pin: !PB16
|
||
|
|
#enable_pin: !PD9
|
||
|
|
#microsteps: 32
|
||
|
|
#heater_pin: PA29
|
||
|
|
#sensor_pin: PB25
|
||
|
|
|
||
|
|
[heater_bed]
|
||
|
|
heater_pin: PA0
|
||
|
|
sensor_type: EPCOS 100K B57560G104F
|
||
|
|
sensor_pin: PA8
|
||
|
|
control: pid
|
||
|
|
pid_kp: 73.517
|
||
|
|
pid_ki: 1.132
|
||
|
|
pid_kd: 1193.728
|
||
|
|
min_temp: 0
|
||
|
|
max_temp: 130
|
||
|
|
|
||
|
|
[fan]
|
||
|
|
pin: PA7
|
||
|
|
|
||
|
|
#[heater_fan fan1]
|
||
|
|
#pin: PA5
|
||
|
|
#heater: extruder
|
||
|
|
|
||
|
|
[mcu]
|
||
|
|
serial: /dev/ttyAMA0
|
||
|
|
|
||
|
|
[printer]
|
||
|
|
kinematics: cartesian
|
||
|
|
max_velocity: 300
|
||
|
|
max_accel: 1000
|
||
|
|
max_z_velocity: 20
|
||
|
|
max_z_accel: 100
|