diff --git a/PrusaSlicer_2.5.0/filament/PLA.ini b/PrusaSlicer_2.5.0/filament/PLA.ini
index 2e98982..390a077 100644
--- a/PrusaSlicer_2.5.0/filament/PLA.ini
+++ b/PrusaSlicer_2.5.0/filament/PLA.ini
@@ -1,5 +1,5 @@
-# generated by PrusaSlicer 2.5.0 on 2023-01-13 at 12:33:34 UTC
-bed_temperature = 60
+# generated by PrusaSlicer 2.5.2 on 2023-06-20 at 11:50:02 UTC
+bed_temperature = 58
 bridge_fan_speed = 80
 compatible_printers = 
 compatible_printers_condition = 
@@ -8,7 +8,7 @@ compatible_prints_condition =
 cooling = 1
 disable_fan_first_layers = 1
 end_filament_gcode = "; Filament-specific end gcode \n;END gcode for filament\n"
-extrusion_multiplier = 0.9
+extrusion_multiplier = 0.964
 fan_always_on = 1
 fan_below_layer_time = 20
 filament_colour = #1C71D8
@@ -17,7 +17,7 @@ filament_cooling_initial_speed = 2.2
 filament_cooling_moves = 4
 filament_cost = 14
 filament_density = 1.24
-filament_deretract_speed = 60
+filament_deretract_speed = 35
 filament_diameter = 1.75
 filament_load_time = 0
 filament_loading_speed = 28
@@ -29,12 +29,12 @@ filament_ramming_parameters = "120 100 6.6 6.8 7.2 7.6 7.9 8.2 8.7 9.4 9.9 10.0|
 filament_retract_before_travel = nil
 filament_retract_before_wipe = nil
 filament_retract_layer_change = nil
-filament_retract_length = 0.8
+filament_retract_length = 0.75
 filament_retract_lift = nil
 filament_retract_lift_above = nil
 filament_retract_lift_below = nil
 filament_retract_restart_extra = nil
-filament_retract_speed = 60
+filament_retract_speed = 40
 filament_settings_id = ""
 filament_soluble = 0
 filament_spool_weight = 0
@@ -45,13 +45,13 @@ filament_unloading_speed = 90
 filament_unloading_speed_start = 100
 filament_vendor = Generic
 filament_wipe = nil
-first_layer_bed_temperature = 60
-first_layer_temperature = 212
+first_layer_bed_temperature = 58
+first_layer_temperature = 205
 full_fan_speed_layer = 4
 inherits = 
 max_fan_speed = 100
 min_fan_speed = 70
 min_print_speed = 30
-slowdown_below_layer_time = 3
-start_filament_gcode = "; Filament gcode\nSET_PRESSURE_ADVANCE ADVANCE=0.07\n{if filament_retract_length[current_extruder]> 0}SET_RETRACTION RETRACT_LENGTH=[filament_retract_length]{endif}\n{if filament_retract_speed[current_extruder] > 0}SET_RETRACTION RETRACT_SPEED=[filament_retract_speed]{endif}\n{if filament_deretract_speed[current_extruder] > 0}SET_RETRACTION UNRETRACT_SPEED=[filament_deretract_speed]{endif}\n{if filament_retract_restart_extra[current_extruder] > 0}SET_RETRACTION UNRETRACT_EXTRA_LENGTH=[filament_retract_restart_extra]{endif}\n"
-temperature = 210
+slowdown_below_layer_time = 7
+start_filament_gcode = "; Filament gcode\nSET_PRESSURE_ADVANCE ADVANCE=0.078\n{if filament_retract_length[current_extruder]> 0}SET_RETRACTION RETRACT_LENGTH=[filament_retract_length]{endif}\n{if filament_retract_speed[current_extruder] > 0}SET_RETRACTION RETRACT_SPEED=[filament_retract_speed]{endif}\n{if filament_deretract_speed[current_extruder] > 0}SET_RETRACTION UNRETRACT_SPEED=[filament_deretract_speed]{endif}\n{if filament_retract_restart_extra[current_extruder] > 0}SET_RETRACTION UNRETRACT_EXTRA_LENGTH=[filament_retract_restart_extra]{endif}\n"
+temperature = 198
diff --git a/PrusaSlicer_2.5.0/print/0.24 - Sport (0.4).ini b/PrusaSlicer_2.5.0/print/0.24 - Sport (0.4).ini
index df68acb..5618b44 100644
--- a/PrusaSlicer_2.5.0/print/0.24 - Sport (0.4).ini	
+++ b/PrusaSlicer_2.5.0/print/0.24 - Sport (0.4).ini	
@@ -1,4 +1,4 @@
-# generated by PrusaSlicer 2.5.0 on 2023-01-18 at 13:29:51 UTC
+# generated by PrusaSlicer 2.5.0 on 2023-01-21 at 12:09:05 UTC
 avoid_crossing_perimeters = 0
 avoid_crossing_perimeters_max_detour = 0
 bottom_fill_pattern = monotonic
@@ -20,7 +20,7 @@ dont_support_bridges = 1
 draft_shield = disabled
 elefant_foot_compensation = 0.1
 ensure_vertical_shell_thickness = 0
-external_perimeter_extrusion_width = 0.44
+external_perimeter_extrusion_width = 0.48
 external_perimeter_speed = 160
 external_perimeters_first = 0
 extra_perimeters = 1