In an initial install, the following is a potential rule ordering:
```
Notice: /Stage[main]/Zulip::Supervisor/File[/etc/supervisor/conf.d/zulip]/ensure: created
Notice: /Stage[main]/Zulip::Supervisor/File[/etc/supervisor/supervisord.conf]/content: content changed '{md5}99dc7e8a1178ede9ae9794aaecbca436' to '{md5}7ef9771d2c476c246a3ebd95fab784cb'
Notice: /Stage[main]/Zulip::Supervisor/Exec[supervisor-restart]: Triggered 'refresh' from 1 event
[...]
Notice: /Stage[main]/Zulip::App_frontend_base/File[/etc/supervisor/conf.d/zulip/zulip.conf]/ensure: defined content as '{md5}d98ac8a974d44efb1d1bb2ef8b9c3dee'
[...]
Notice: /Stage[main]/Zulip::App_frontend_once/File[/etc/supervisor/conf.d/zulip/zulip-once.conf]/ensure: defined content as '{md5}53f56ae4b95413bfd7a117e3113082dc'
[...]
Notice: /Stage[main]/Zulip::Process_fts_updates/File[/etc/supervisor/conf.d/zulip/zulip_db.conf]/ensure: defined content as '{md5}96092d7f27d76f48178a53b51f80b0f0'
Notice: /Stage[main]/Zulip::Supervisor/Service[supervisor]/ensure: ensure changed 'stopped' to 'running'
```
The last line is misleading -- supervisor was already started by the
`supervisor-restart` process on the third line. As can be shown with
`zulip-puppet-apply --debug`, the last line just installs supervisor
to run on startup, using `systemctl`:
```
Debug: Executing: 'supervisorctl status'
Debug: Executing: '/usr/bin/systemctl unmask supervisor'
Debug: Executing: '/usr/bin/systemctl start supervisor'
```
This means the list of processes started by supervisor depends
entirely on which configuration files were successfully written out by
puppet before the initial `supervisor-restart` ran. Since
`zulip_db.conf` is written later than the rest, the initial install
often fails to start the `process-fts-updates` process. In this
state, an explicit `supervisorctl restart` or `supervisorctl reread &&
supervisorctl update` is required for the service to be found and
started.
Reorder the `supervisor-restart` exec to only run after the service is
started. Because all supervisor configuration files have a `notify`
of the service, this forces the ordering of:
```
(package) -> (config files) -> (service) -> (optional restart)
```
On first startup, this will start and them immediately restart
supervisor, which is unfortunate but unavoidable -- and not terribly
relevant, since the database will not have been created yet, and thus
most processes will be in a restart loop for failing to connect to it.
The sysvinit script for supervisor has a long-standing bug where
`/etc/init.d/supervisor restart` stops but does not then start the
supervisor process.
Work around this by making restart then try to start, and return if it
is currently running.
Not having the package installed will cause startup failures in
`process_fts_updates`; ensure that we've installed the package before
we potentially start the service.
93f62b999e removed the last file in
puppet/zulip/files/nagios_plugins/zulip_nagios_server, which means the
singular rule in zulip::nagios no longer applies cleanly.
Remove the `zulip::nagios` class, as it is no longer needed.
An organization with at most 5 users that is behind on payments isn't
worth spending time on investigating the situation.
For larger organizations, we likely want somewhat different logic that
at least does not void invoices.
Staging and other hosts that are `zulip::app_frontend_base` but not
`zulip::app_frontend_once` do not have a
/etc/supervisor/conf.d/zulip/zulip-once.conf and as such do not have
`zulip_deliver_scheduled_emails` or `zulip_deliver_scheduled_messages`
and thus supervisor will fail to reload.
Making the contents of `zulip-workers` contingent on if the server is
_also_ a `-once` server is complicated, and would involve using Concat
fragments, which severely limit readability.
Instead, expel those two from `zulip-workers`; this is somewhat
reasonable, since they are use an entirely different codepath from
zulip_events_*, using the database rather than RabbitMQ for their
queuing.
This is similar cleanup to 3ab9b31d2f, but only affects zulip_ops
services; it serves to ensure that any of these services which are no
longer enabled are automatically removed from supervisor.
Note that this will cause a supervisor restart on all affected hosts,
which will restart all supervisor services.
Failure to do this results in:
```
psql: error: failed to connect to `host=localhost user=zulip database=zulip`: failed to write startup message (x509: certificate is valid for [redacted], not localhost)
```
Host-based md5 auth for 127.0.0.1 must be removed from `pg_hba.conf`,
otherwise password authentication is preferred over certificate-based
authentication for localhost.
Nagios refuses to allow any modifications with use_authentication off;
re-enabled "authentication" but set a default user, which (by way of
the `*` permissions in 359f37389a) is allowed to take all actions.
This requires switching to a reverse tunnel for the auth connection,
with the side effect that the `zulip_ops::teleport::node` manifest can
be applied on servers anywhere in the Internet; they do not need to
have any publicly-available open ports.
This means that services will only open their ports if they are
actually run, without having to clutter rules.v4 with a log of `if`
statements.
This does not go as far as using `puppetlabs/firewall`[1] because that
would represent an additional DSL to learn; raw IPtables sections can
easily be inserted into the generated iptables file via
`concat::fragment` (either inline, or as a separate file), but config
can be centralized next to the appropriate service.
[1] https://forge.puppet.com/modules/puppetlabs/firewall
Using puppet modules from the puppet forge judiciously will allow us
to simplify the configuration somewhat; this specifically pulls in the
stdlib module, which we were already using parts of.
This moves the `.asc` files into subdirectories, and writes out the
according `.list` files into them. It moves from templates to
written-out `.list` files for clarity and ease of
implementation (Debian and Ubuntu need different templates for
`zulip`), and as a way of making explicit which releases are supported
for each list. For the special-case of the PGroonga signing key, we
source an additional file within the directory.
This simplifies the process for adding another class of `.list` file.
Rather than duplicate logic from `computed_settings`, use the values
that were computed therein.
Co-authored-by: Adam Birds <adam.birds@adbwebdesigns.co.uk>
Using the second branch _only_ for case (3), of a PostgreSQL server on
a different host, leaves it untested in CI. It also brings in an
unnecessary Django dependency.
Co-authored-by: Adam Birds <adam.birds@adbwebdesigns.co.uk>
We only need to read the `zulip.conf` file to determine if we're using
PGROONGA if we are on the PostgreSQL machine, with no access to
Django.
Co-authored-by: Adam Birds <adam.birds@adbwebdesigns.co.uk>
The only way in which "host" could be set is in cases (1) or (2), when
it was potentially read from Django's settings. In case (3), we
already know we are on the same host as the PostgreSQL server.
This unifies the two separated checks, which are actually the same
check.
Co-authored-by: Adam Birds <adam.birds@adbwebdesigns.co.uk>
Mateusz Mandera
Alex Vandiver
Anders Kaseorg
Vishnu KS