We should eventually add templating for the set of hosts here, but
it's worth merging this change to remove the deleted hostname and
replace it with the current one.
Disabled on webservers in 047817b6b0, it has since lingered in
configuration, as well as running (to no effect) every minute on the
loadbalancer.
Remove the vestiges of its configuration.
This banner shows on lb1, advertising itself as lb0. There is no
compelling reason for a custom motd, especially one which needs to
be reconfigured for each host.
Since this was using repead individual get() calls previously, it
could not be monitored for having a consumer. Add it in, by marking
it of queue type "consumer" (the default), and adding Nagios lines for
it.
Also adjust missedmessage_emails to be monitored; it stopped using
LoopQueueProcessingWorker in 5cec566cb9, but was never added back
into the set of monitored consumers.
The rabbitmq cron jobs exist in order to call rabbitmqctl as root and
write the output to files that nagios can consume, since nagios is not
allowed to run rabbitmqctl.
In systems which do not have nagios configured, these every-minute
cron jobs add non-insignificant load, to no effect. Move their
installation into `zulip_ops`. In doing so, also combine the cron.d
files into a single file; this allows us to `ensure => absent` the old
filenames, removing them from existing systems. Leave the resulting
combined cron.d file in `zulip`, since it is still of general utility
and note.
The configuration change made in 1c17583ad5 only allowed delivery to
those specific Zulip addresses. However, they also prevent the
mailserver from being used as an outgoing email relay from Zulip,
since all mail that passed through the mailserver (from any
originator) was required to have a `RCPT TO` that matched those
regexes.
Allow mail originating from `mynetworks` to have an arbitrary
addresses in `RCPT TO`.
Use the validation of the tornado sharding config that
`stage_updated_sharding` does, by depending on it. This ensures that
we don't write out a supervisor or nginx config based on a
bad (e.g. non-sequential) list of tornado ports.
Fingerprinting the config is somewhat brittle -- it requires either
custom bootstrapping for old (fingerprint-less) configs, and may have
false-positives.
Since generating the config is lightweight, do so into the .tmp files,
and compare the output to the originals to determine if there are
changes to apply.
In order to both surface errors, as well as notify the user in case a
restart is necessary, we must run it twice. The `onlyif`
functionality cannot show configuration errors to the user, only
determine if the command runs or not. We thus run the command once,
judging errors as "interesting" enough to run the actual command,
whose failure will be verbose in Puppet and halt any steps that depend
on it.
Removing the `onlyif` would result in `stage_updated_sharding` showing
up in the output of every Puppet run, which obscures the important
messages it displays when an update to sharding is necessary.
Removing the `command` (e.g. making it an `echo`) would result in
removing the ability to report configuration errors. We thus have no
choice but to run it twice; this is thankfully low-overhead.
We can compute the intended number of processes from the sharding
configuration. In doing so, also validate that all of the ports are
contiguous.
This removes a discrepancy between `scripts/lib/sharding.py` and other
parts of the codebase about if merely having a `[tornado_sharding]`
section is sufficient to enable sharding. Having behaviour which
changes merely based on if an empty section exists is surprising.
This does require that a (presumably empty) `9800` configuration line
exist, but making that default explicit is useful.
After this commit, configuring sharding can be done by adding to
`zulip.conf`:
```
[tornado_sharding]
9800 = # default
9801 = other_realm
```
Followed by running `./scripts/refresh-sharding-and-restart`.
In development and test, we keep the Tornado port at 9993 and 9983,
respectively; this allows tests to run while a dev instance is
running.
In production, moving to port 9800 consistently removes an odd edge
case, when just one worker is on an entirely different port than if
two workers are used.
Without an explicit port number, the `stdout_logfile` values for each
port are identical. Supervisor apparently decides that it will
de-conflict this by appending an arbitrary number to the end:
```
/var/log/zulip/tornado.log
/var/log/zulip/tornado.log.1
/var/log/zulip/tornado.log.10
/var/log/zulip/tornado.log.2
/var/log/zulip/tornado.log.3
/var/log/zulip/tornado.log.7
/var/log/zulip/tornado.log.8
/var/log/zulip/tornado.log.9
```
This is quite confusing, since most other files in `/var/log/zulip/`
use `.1` to mean logrotate was used. Also note that these are not all
sequential -- 4, 5, and 6 are mysteriously missing, though they were
used in previous restarts. This can make it extremely hard to debug
logs from a particular Tornado shard.
Give the logfiles a consistent name, and set them up to logrotate.
Making this include "zulip-tornado" makes it clearer in supervisor
logs. Without this, one only sees:
```
2020-09-14 03:43:13,788 INFO waiting for port-9807 to stop
2020-09-14 03:43:14,466 INFO stopped: port-9807 (exit status 1)
2020-09-14 03:43:14,469 INFO spawned: 'port-9807' with pid 24289
2020-09-14 03:43:15,470 INFO success: port-9807 entered RUNNING state, process has stayed up for > than 1 seconds (startsecs)
```
This supports running puppet to pick up new sharding changes, which
will warn of the need to finalize them via
`refresh-sharding-and-restart`, or simply running that directly.
Clients that close their socket to nginx suddenly also cause nginx to close
its connection to uwsgi. When uwsgi finishes computing the response,
it thus tries to write to a closed socket, and generates either
IOError or SIGPIPE failures.
Since these are caused by the _client_ closing the connection
suddenly, they are not actionable by the server. At particularly high
volumes, this could represent some sort of server-side failure;
however, this is better detected by examining status codes at the
loadbalancer. nginx uses the error code 499 for this occurrence:
https://httpstatuses.com/499
Stop uwsgi from generating this family of exception entirely, using
configuration for uwsgi[1]; it documents these errors as "(annoying),"
hinting at their general utility."
[1] https://uwsgi-docs.readthedocs.io/en/latest/Options.html#ignore-sigpipe
Increasing the uwsgi listen backlog is intended to allow it to handle
higher connection rates during server restart, when many clients may
be trying to connect. The kernel, in turn, needs to have a
proportionally increased somaxconn soas to not refuse the connection.
Set somaxconn to 2x the uwsgi backlog, but no lower than the
default (128).
Prior to PostgreSQL 12, the `recovery_target_timeline` setting is only
valid in a `recovery.conf` file, as that file has its own
configuration parser. As such, including it in `postgresql.conf`
results in an error, and PostgreSQL will fail to start.
Remove the setting, reverting bff3b540b1. This fixes PostgreSQL 9.5,
9.6, 10, and 11; while the setting is not an error in a PostgreSQL 12
configuration file, it is unnecessary since `latest` is the default.
7d4a370a57 attempted to move the replication check to on the
PostgreSQL hosts. While it updated the _check_ to assume it was
running and talking to a local PostgreSQL instance, the configuration
and installation for the check were not updated. As such, the check
ran on the nagios host for each DB host, and produced no output.
Start distributing the check to all apopdb hosts, and configure nagios
to use the SSH tunnel to get there.
wal-g was used in `puppet/zulip` by env-wal-g, but only installed in
`puppet/zulip_ops`.
Merge all of the dependencies of doing backups using wal-g (wal-g
installation, the pg_backup_and_purge job, the nagios plugin that
verifies it happens) into a common base class in `puppet/zulip`, since
it is generally useful.
No plugins are installed inside the /usr/local/munin/lib this creates
in munin-node, nor are they symlinked into /etc/munin/plugins, so
non-default plugins are added by this.
Alex Vandiver
Tim Abbott
Anders Kaseorg
Casper Kvan Clausen