mirror of https://github.com/Desuuuu/klipper.git
80 lines
1.5 KiB
INI
80 lines
1.5 KiB
INI
# This file contains pin mappings for the Tronxy X5S (circa 2017). To
|
|
# use this config, the firmware should be compiled for the AVR
|
|
# atmega1284p.
|
|
|
|
# Note, a number of Melzi boards are shipped without a bootloader. In
|
|
# that case, an external programmer will be needed to flash a
|
|
# bootloader to the board (for example, see
|
|
# http://www.instructables.com/id/Flashing-a-Bootloader-to-the-CR-10/
|
|
# ). Once that is done, one should be able to use the standard "make
|
|
# flash" command to flash Klipper.
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PD7
|
|
dir_pin: !PC5
|
|
enable_pin: !PD6
|
|
step_distance: .0125
|
|
endstop_pin: ^!PC2
|
|
position_endstop: 0
|
|
position_max: 330
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PC6
|
|
dir_pin: !PC7
|
|
enable_pin: !PD6
|
|
step_distance: .0125
|
|
endstop_pin: ^!PC3
|
|
position_endstop: 0
|
|
position_max: 310
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PB3
|
|
dir_pin: PB2
|
|
enable_pin: !PD6
|
|
step_distance: 0.0025
|
|
endstop_pin: ^!PC4
|
|
position_endstop: 0.5
|
|
position_max: 400
|
|
|
|
[extruder]
|
|
step_pin: PB1
|
|
dir_pin: PB0
|
|
enable_pin: !PD6
|
|
step_distance: .0111
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PD5
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PA7
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 275
|
|
|
|
[heater_bed]
|
|
heater_pin: PD4
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PA6
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 150
|
|
|
|
[fan]
|
|
pin: PB4
|
|
|
|
[mcu]
|
|
serial: /dev/ttyUSB0
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 300
|
|
max_accel: 1000
|
|
max_z_velocity: 20
|
|
max_z_accel: 100
|