mirror of https://github.com/Desuuuu/klipper.git
125 lines
3.6 KiB
INI
125 lines
3.6 KiB
INI
# This file contains an example configuration for the Replicape rev B3
|
|
# board. To use this config, one must compile and install the
|
|
# micro-controller code for the "Beaglebone PRU", and then compile and
|
|
# install the micro-controller code a second time for a "Linux
|
|
# process".
|
|
|
|
# NOTE: Klipper does not alter the input/output state of the
|
|
# Beaglebone pins and it does not control their pull-up resistors.
|
|
# Typically the correct settings are automatically applied when the
|
|
# Beaglebone detects the Replicape board, but if changes are needed
|
|
# they must be specified in a "device tree overlay" or via the
|
|
# config-pin program.
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: P8_17
|
|
dir_pin: P8_26
|
|
enable_pin: replicape:stepper_x_enable
|
|
step_distance: .0125
|
|
endstop_pin: ^P9_25
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: P8_12
|
|
dir_pin: P8_19
|
|
enable_pin: replicape:stepper_y_enable
|
|
step_distance: .0125
|
|
endstop_pin: ^P9_23
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: P8_13
|
|
dir_pin: P8_14
|
|
enable_pin: replicape:stepper_z_enable
|
|
step_distance: 0.00025
|
|
endstop_pin: ^P9_13
|
|
position_endstop: 0
|
|
position_max: 200
|
|
|
|
[extruder]
|
|
step_pin: P9_12
|
|
dir_pin: P8_15
|
|
enable_pin: replicape:stepper_e_enable
|
|
step_distance: .002
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: replicape:power_e
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: host:analog4
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[heater_bed]
|
|
heater_pin: replicape:power_hotbed
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: host:analog6
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: replicape:power_fan0
|
|
|
|
[mcu]
|
|
serial: /dev/rpmsg_pru30
|
|
pin_map: beaglebone
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 25
|
|
max_z_accel: 30
|
|
|
|
[mcu host]
|
|
serial: /tmp/klipper_host_mcu
|
|
|
|
# The "replicape" config section adds "replicape:stepper_x_enable"
|
|
# virtual stepper enable pins (for steppers x, y, z, e, and h) and
|
|
# "replicape:power_x" PWM output pins (for hotbed, e, h, fan0, fan1,
|
|
# fan2, and fan3) that may then be used elsewhere in the config file.
|
|
[replicape]
|
|
revision: B3
|
|
# The replicape hardware revision. Currently only revision "B3" is
|
|
# supported. This parameter must be provided.
|
|
#enable_pin: !P9_41
|
|
# The replicape global enable pin. The default is !P9_41.
|
|
host_mcu: host
|
|
# The name of the mcu config section that communicates with the
|
|
# Klipper "linux process" mcu instance. This parameter must be
|
|
# provided.
|
|
stepper_x_microstep_mode: spread16
|
|
# This parameter controls the CFG1 and CFG2 pins of the given
|
|
# stepper motor driver. Available options are: disable, 1, 2,
|
|
# spread2, 4, 16, spread4, spread16, stealth4, and stealth16. The
|
|
# default is disable.
|
|
stepper_x_current: 0.5
|
|
# The configured maximum current (in Amps) of the stepper motor
|
|
# driver. This parameter must be provided if the stepper is not in a
|
|
# disable mode.
|
|
#stepper_x_chopper_off_time_high: False
|
|
# This parameter controls the CFG0 pin of the stepper motor driver
|
|
# (True sets CFG0 high, False sets it low). The default is False.
|
|
#stepper_x_chopper_hysteresis_high: False
|
|
# This parameter controls the CFG4 pin of the stepper motor driver
|
|
# (True sets CFG4 high, False sets it low). The default is False.
|
|
#stepper_x_chopper_blank_time_high: True
|
|
# This parameter controls the CFG5 pin of the stepper motor driver
|
|
# (True sets CFG5 high, False sets it low). The default is True.
|
|
stepper_y_microstep_mode: spread16
|
|
stepper_y_current: 0.5
|
|
stepper_z_microstep_mode: spread16
|
|
stepper_z_current: 0.5
|
|
stepper_e_microstep_mode: 16
|
|
stepper_e_current: 0.5
|