mirror of https://github.com/Desuuuu/klipper.git
92 lines
1.8 KiB
INI
92 lines
1.8 KiB
INI
# This file contains common pin mappings for the 2018 Creality
|
|
# Ender 3. To use this config, the firmware should be compiled for the
|
|
# AVR atmega1284p.
|
|
|
|
# Note, a number of Melzi boards are shipped without a bootloader. In
|
|
# that case, an external programmer will be needed to flash a
|
|
# bootloader to the board (for example, see
|
|
# http://www.instructables.com/id/Flashing-a-Bootloader-to-the-CR-10/
|
|
# ). Once that is done, one should be able to use the standard "make
|
|
# flash" command to flash Klipper.
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PD7
|
|
dir_pin: !PC5
|
|
enable_pin: !PD6
|
|
step_distance: .0125
|
|
endstop_pin: ^PC2
|
|
position_endstop: 0
|
|
position_max: 220
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PC6
|
|
dir_pin: !PC7
|
|
enable_pin: !PD6
|
|
step_distance: .0125
|
|
endstop_pin: ^PC3
|
|
position_endstop: 0
|
|
position_max: 220
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PB3
|
|
dir_pin: PB2
|
|
enable_pin: !PA5
|
|
step_distance: .0025
|
|
endstop_pin: ^PC4
|
|
# If you don't like the 0.5 you should change this to 0.0
|
|
position_endstop: 0.5
|
|
position_max: 250
|
|
|
|
[extruder]
|
|
step_pin: PB1
|
|
dir_pin: !PB0
|
|
enable_pin: !PD6
|
|
step_distance: 0.010526
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PD5
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PA7
|
|
control: pid
|
|
# tuned for stock hardware with 200 degree Celsius target
|
|
pid_Kp: 21.527
|
|
pid_Ki: 1.063
|
|
pid_Kd: 108.982
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[heater_bed]
|
|
heater_pin: PD4
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PA6
|
|
control: pid
|
|
# tuned for stock hardware with 50 degree Celsius target
|
|
pid_Kp: 54.027
|
|
pid_Ki: 0.770
|
|
pid_Kd: 948.182
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: PB4
|
|
|
|
[mcu]
|
|
serial: /dev/ttyUSB0
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|
|
|
|
[display]
|
|
lcd_type: st7920
|
|
cs_pin: PA3
|
|
sclk_pin: PA1
|
|
sid_pin: PC1
|