mirror of https://github.com/Desuuuu/klipper.git
69 lines
1.5 KiB
INI
69 lines
1.5 KiB
INI
# This file contains common pin mappings for the BIGTREETECH EBBCan
|
|
# Canbus board. To use this config, the firmware should be compiled for the
|
|
# STM32G0B1 with "8 MHz crystal" and "USB (on PA11/PA12)" or "CAN bus (on PB0/PB1)".
|
|
# The "EBB Can" micro-controller will be used to control the components on the nozzle.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[mcu EBBCan]
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
|
#canbus_uuid: 0e0d81e4210c
|
|
|
|
[adxl345]
|
|
cs_pin: EBBCan: PB12
|
|
spi_software_sclk_pin: EBBCan: PB10
|
|
spi_software_mosi_pin: EBBCan: PB11
|
|
spi_software_miso_pin: EBBCan: PB2
|
|
axes_map: x,y,z
|
|
|
|
[extruder]
|
|
step_pin: EBBCan: PD0
|
|
dir_pin: !EBBCan: PD1
|
|
enable_pin: !EBBCan: PD2
|
|
microsteps: 16
|
|
rotation_distance: 33.500
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: EBBCan: PA2
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: EBBCan: PA3
|
|
control: pid
|
|
pid_Kp: 21.527
|
|
pid_Ki: 1.063
|
|
pid_Kd: 108.982
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
# sensor_type:MAX31865
|
|
# sensor_pin: EBBCan: PA4
|
|
# spi_bus: spi1
|
|
# rtd_nominal_r: 100
|
|
# rtd_reference_r: 430
|
|
# rtd_num_of_wires: 2
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: EBBCan: PA15
|
|
run_current: 0.650
|
|
stealthchop_threshold: 999999
|
|
|
|
[fan]
|
|
pin: EBBCan: PA0
|
|
|
|
[heater_fan hotend_fan]
|
|
pin: EBBCan: PA1
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
|
|
#[neopixel hotend_rgb]
|
|
#pin: EBBCan:PD3
|
|
|
|
#[bltouch]
|
|
#sensor_pin: ^EBBCan:PB8
|
|
#control_pin: EBBCan:PB9
|
|
|
|
#[filament_switch_sensor switch_sensor]
|
|
#switch_pin: EBBCan:PB4
|
|
|
|
#[filament_motion_sensor motion_sensor]
|
|
#switch_pin: ^EBBCan:PB3
|