mirror of https://github.com/Desuuuu/klipper.git
252 lines
5.0 KiB
INI
252 lines
5.0 KiB
INI
# This file contains common pin mappings for the BIGTREETECH SKR V1.3
|
|
# board. To use this config, the firmware should be compiled for the
|
|
# LPC1768.
|
|
|
|
# See the example.cfg file for a description of available parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: P2.2
|
|
dir_pin: !P2.6
|
|
enable_pin: !P2.1
|
|
step_distance: .0125
|
|
endstop_pin: P1.29 # P1.28 for X-max
|
|
position_endstop: 0
|
|
position_max: 320
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: P0.19
|
|
dir_pin: !P0.20
|
|
enable_pin: !P2.8
|
|
step_distance: .0125
|
|
endstop_pin: P1.27 # P1.26 for Y-max
|
|
position_endstop: 0
|
|
position_max: 300
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: P0.22
|
|
dir_pin: P2.11
|
|
enable_pin: !P0.21
|
|
step_distance: .0025
|
|
endstop_pin: P1.25 # P1.24 for Z-max
|
|
position_endstop: 0.5
|
|
position_max: 400
|
|
|
|
[extruder]
|
|
step_pin: P2.13
|
|
dir_pin: !P0.11
|
|
enable_pin: !P2.12
|
|
step_distance: .010526
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: P2.7
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: P0.24
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 260
|
|
|
|
#[extruder1]
|
|
#step_pin: P0.1
|
|
#dir_pin: P0.0
|
|
#enable_pin: !P0.10
|
|
#heater_pin: P2.4
|
|
#sensor_pin: P0.25
|
|
#...
|
|
|
|
[heater_bed]
|
|
heater_pin: P2.5
|
|
sensor_type: ATC Semitec 104GT-2
|
|
sensor_pin: P0.23
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: P2.3
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 200
|
|
max_accel: 2000
|
|
max_z_velocity: 25
|
|
max_z_accel: 100
|
|
|
|
|
|
########################################
|
|
# TMC2208 configuration
|
|
########################################
|
|
|
|
# For TMC2208 UART
|
|
# 1) Remove all of the jumpers below the stepper drivers
|
|
# 2) Place jumpers on the red pin headers labeled XUART (XUART, YUART etc.)
|
|
|
|
#[tmc2208 stepper_x]
|
|
#uart_pin: P1.17
|
|
#microsteps: 16
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2208 stepper_y]
|
|
#uart_pin: P1.15
|
|
#microsteps: 16
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2208 stepper_z]
|
|
#uart_pin: P1.10
|
|
#microsteps: 16
|
|
#run_current: 0.650
|
|
#hold_current: 0.450
|
|
#stealthchop_threshold: 30
|
|
|
|
#[tmc2208 extruder]
|
|
#uart_pin: P1.8
|
|
#microsteps: 16
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 5
|
|
|
|
#[tmc2208 extruder1]
|
|
#uart_pin: P1.1
|
|
#microsteps: 16
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 5
|
|
|
|
|
|
########################################
|
|
# TMC2130 configuration
|
|
########################################
|
|
|
|
# For TMC SPI
|
|
# 1) Place jumpers on all the red pin headers under the stepper drivers
|
|
# 2) Remove jumpers from the red pin headers labeled XUART (XUART, YUART etc.)
|
|
|
|
#[tmc2130 stepper_x]
|
|
#cs_pin: P1.17
|
|
#spi_software_sclk_pin: P0.4
|
|
#spi_software_mosi_pin: P4.28
|
|
#spi_software_miso_pin: P0.5
|
|
##diag1_pin: P1.29
|
|
#microsteps: 16
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2130 stepper_y]
|
|
#cs_pin: P1.15
|
|
#spi_software_sclk_pin: P0.4
|
|
#spi_software_mosi_pin: P4.28
|
|
#spi_software_miso_pin: P0.5
|
|
##diag1_pin: P1.27
|
|
#microsteps: 16
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 250
|
|
|
|
#[tmc2130 stepper_z]
|
|
#cs_pin: P1.10
|
|
#spi_software_sclk_pin: P0.4
|
|
#spi_software_mosi_pin: P4.28
|
|
#spi_software_miso_pin: P0.5
|
|
##diag1_pin: P1.25
|
|
#microsteps: 16
|
|
#run_current: 0.650
|
|
#hold_current: 0.450
|
|
#stealthchop_threshold: 30
|
|
|
|
#[tmc2130 extruder]
|
|
#cs_pin: P1.8
|
|
#spi_software_sclk_pin: P0.4
|
|
#spi_software_mosi_pin: P4.28
|
|
#spi_software_miso_pin: P0.5
|
|
##diag1_pin: P1.28
|
|
#microsteps: 16
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 5
|
|
|
|
#[tmc2130 extruder1]
|
|
#cs_pin: P1.1
|
|
#spi_software_sclk_pin: P0.4
|
|
#spi_software_mosi_pin: P4.28
|
|
#spi_software_miso_pin: P0.5
|
|
##diag1_pin: P1.26
|
|
#microsteps: 16
|
|
#run_current: 0.800
|
|
#hold_current: 0.500
|
|
#stealthchop_threshold: 5
|
|
|
|
|
|
########################################
|
|
# Optional LCD configuration
|
|
########################################
|
|
|
|
# "RepRapDiscount 128x64 Full Graphic Smart Controller" type displays
|
|
#[display]
|
|
#lcd_type: st7920
|
|
#cs_pin: P1.19
|
|
#sclk_pin: P1.20
|
|
#sid_pin: P1.18
|
|
#encoder_pins: ^P3.26, ^P3.25
|
|
#click_pin: ^!P0.28
|
|
#
|
|
#[output_pin beeper]
|
|
#pin: P1.30
|
|
|
|
# "RepRapDiscount 2004 Smart Controller" type displays
|
|
#[display]
|
|
#lcd_type: hd44780
|
|
#rs_pin: P1.19
|
|
#e_pin: P1.18
|
|
#d4_pin: P1.20
|
|
#d5_pin: P1.21
|
|
#d6_pin: P1.22
|
|
#d7_pin: P1.23
|
|
#encoder_pins: ^P3.26, ^P3.25
|
|
#click_pin: ^!P0.28
|
|
#
|
|
#[output_pin beeper]
|
|
#pin: P1.30
|
|
|
|
# 128x64 Full Graphic Creality CR10 / ENDER 3 stockdisplay
|
|
#[display]
|
|
#lcd_type: st7920
|
|
#cs_pin: P1.19
|
|
#sclk_pin: P1.21
|
|
#sid_pin: P1.23
|
|
#encoder_pins: ^P1.18, ^P1.20
|
|
#click_pin: !P0.28
|
|
#
|
|
#[output_pin beeper]
|
|
#pin: P1.30
|
|
|
|
# MKS Mini 12864 LCD.
|
|
# Make sure that the EXP1 and EXP2 are rotated correctly on the
|
|
# display board. The cutouts on the connectors should be towards the
|
|
# center of the PCB. See:
|
|
# https://reprap.org/wiki/MKS_MINI_12864#Physical_Interface
|
|
# If they are wrong, the connector housing can be pried off carefully
|
|
# with a small screwdriver and relocated the correct way.
|
|
#
|
|
#[display]
|
|
#lcd_type: uc1701
|
|
#cs_pin: P1.21
|
|
#a0_pin: P1.22
|
|
#contrast: 40
|
|
#encoder_pins: ^P3.25, ^P3.26
|
|
#click_pin: ^!P0.28
|
|
#
|
|
#[output_pin beeper]
|
|
#pin: P1.30
|