mirror of https://github.com/Desuuuu/klipper.git
119 lines
1.9 KiB
INI
119 lines
1.9 KiB
INI
# This file contains common pin mappings for Duet2 Eth/Wifi boards. To
|
|
# use this config, the firmware should be compiled for the SAM4E8E.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[stepper_x]
|
|
step_pin: PD6
|
|
dir_pin: PD11
|
|
enable_pin: !PC6
|
|
step_distance: .0125
|
|
endstop_pin: ^PC14
|
|
position_endstop: 0
|
|
position_max: 250
|
|
|
|
[tmc2660 stepper_x]
|
|
cs_pin: PD14
|
|
spi_bus: usart1
|
|
microsteps: 16
|
|
run_current: 1.000
|
|
sense_resistor: 0.051
|
|
|
|
[stepper_y]
|
|
step_pin: PD7
|
|
dir_pin: !PD12
|
|
enable_pin: !PC6
|
|
step_distance: .0125
|
|
endstop_pin: ^PA2
|
|
position_endstop: 0
|
|
position_max: 210
|
|
|
|
[tmc2660 stepper_y]
|
|
cs_pin: PC9
|
|
spi_bus: usart1
|
|
microsteps: 16
|
|
run_current: 1.000
|
|
sense_resistor: 0.051
|
|
|
|
[stepper_z]
|
|
step_pin: PD8
|
|
dir_pin: PD13
|
|
enable_pin: !PC6
|
|
step_distance: .0025
|
|
endstop_pin: ^PD29
|
|
#endstop_pin: PD10 # E0 endstop
|
|
#endstop_pin: PC16 # E1 endstop
|
|
position_endstop: 0.5
|
|
position_max: 200
|
|
|
|
[tmc2660 stepper_z]
|
|
cs_pin: PC10
|
|
spi_bus: usart1
|
|
microsteps: 16
|
|
run_current: 1.000
|
|
sense_resistor: 0.051
|
|
|
|
[extruder]
|
|
step_pin: PD5
|
|
dir_pin: PA1
|
|
enable_pin: !PC6
|
|
step_distance: .002
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: !PA20
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC15
|
|
control: pid
|
|
pid_Kp: 22.2
|
|
pid_Ki: 1.08
|
|
pid_Kd: 114
|
|
min_temp: 0
|
|
max_temp: 250
|
|
|
|
[tmc2660 extruder]
|
|
cs_pin: PC17
|
|
spi_bus: usart1
|
|
microsteps: 16
|
|
run_current: 1.000
|
|
sense_resistor: 0.051
|
|
|
|
#[extruder1]
|
|
#step_pin: PD4
|
|
#dir_pin: PD9
|
|
#enable_pin: !PC6
|
|
#heater_pin: !PA16
|
|
#sensor_pin: PC12
|
|
#...
|
|
#[tmc2660 extruder1]
|
|
#cs_pin: PC25
|
|
#spi_bus: usart1
|
|
#sense_resistor: 0.051
|
|
#...
|
|
|
|
[heater_bed]
|
|
heater_pin: !PA19
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC13
|
|
control: watermark
|
|
min_temp: 0
|
|
max_temp: 130
|
|
|
|
[fan]
|
|
pin: PC23 # FAN0
|
|
|
|
#[heater_fan nozzle_cooling_fan]
|
|
#pin: PC26 # FAN1
|
|
|
|
#[heater_fan board_cooling_fan]
|
|
#pin: PA0 # FAN2
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-Klipper_Klipper_firmware_12345-if00
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 300
|
|
max_accel: 3000
|
|
max_z_velocity: 5
|
|
max_z_accel: 100
|