mirror of https://github.com/Desuuuu/klipper.git
163 lines
5.1 KiB
INI
163 lines
5.1 KiB
INI
# This file contains common configurations and pin mappings for the FOKOOS
|
|
# Odin-5 F3, which uses the MKS Robin Nano v1.2 board. The printer's TFT
|
|
# touchscreen is not currently supported by Klipper, so the touchscreen will
|
|
# permanently display "Booting..." after the Klipper firmware is flashed; use
|
|
# Fluidd, Mainsail, or OctoPrint etc. to control the printer.
|
|
|
|
# WARNING: The printer's Z endstop inductive sensor is not very accurate, so
|
|
# stepper_z:position_endstop has been set to 0.0, for safety, below. This will
|
|
# prevent the nozzle crashing into the bed when you first home Z. You must
|
|
# follow Klipper's instructions for manually calibrating the Z endstop offset
|
|
# before you print anything. Be sure to leave room for a margin of error when
|
|
# you choose this parameter, i.e. choose a value 0.2-0.3mm smaller than the
|
|
# output of the calibration. For example, you might find the actual Z endstop
|
|
# position is at 0.5mm, in which case you could set the value to 0.2mm. It is
|
|
# recommended to manually level the bed before each print.
|
|
|
|
# This configuration does support the addition of a BLtouch. See below for
|
|
# further instructions.
|
|
|
|
# To use this config, the firmware should be compiled for the STM32F103. When
|
|
# running "make menuconfig", enable "extra low-level configuration setup",
|
|
# select the 28KiB bootloader, and serial (on USART3 PB11/PB10) communication.
|
|
# Connect the printer to your Raspberry Pi using the printer's USB port.
|
|
|
|
# Note that the "make flash" command does not work with MKS Robin
|
|
# boards. After running "make", run the following command:
|
|
# ./scripts/update_mks_robin.py out/klipper.bin out/Robin_nano35.bin
|
|
# Copy the file out/Robin_nano35.bin to an SD card and then restart the
|
|
# printer with that SD card. The firmware will automatically be flashed.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[mcu]
|
|
serial: /dev/serial/by-id/usb-1a86_USB_Serial-if00-port0
|
|
restart_method: command
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 250
|
|
max_accel: 1000
|
|
max_z_velocity: 25
|
|
max_z_accel: 100
|
|
|
|
[bed_screws]
|
|
screw1: 33,33
|
|
screw2: 203,33
|
|
screw3: 203,201
|
|
screw4: 33,201
|
|
|
|
[stepper_x]
|
|
step_pin: PE3
|
|
dir_pin: !PE2
|
|
enable_pin: !PE4
|
|
microsteps: 16
|
|
# full_steps_per_rotation: 200
|
|
# rotation_distance = <full_steps_per_rotation> * <microsteps> / <steps_per_mm>
|
|
# 200 * 16 / 80 = 40
|
|
rotation_distance: 40
|
|
endstop_pin: !PA15
|
|
position_endstop: 0
|
|
position_max: 235
|
|
homing_speed: 50
|
|
|
|
[stepper_y]
|
|
step_pin: PE0
|
|
dir_pin: !PB9
|
|
enable_pin: !PE1
|
|
microsteps: 16
|
|
# full_steps_per_rotation: 200
|
|
# rotation_distance = <full_steps_per_rotation> * <microsteps> / <steps_per_mm>
|
|
# 200 * 16 / 80 = 40
|
|
rotation_distance: 40
|
|
endstop_pin: PA12
|
|
position_endstop: 0
|
|
position_max: 235
|
|
homing_speed: 50
|
|
|
|
[stepper_z]
|
|
step_pin: PB5
|
|
dir_pin: PB4
|
|
enable_pin: !PB8
|
|
microsteps: 16
|
|
# full_steps_per_rotation: 200
|
|
# rotation_distance = <full_steps_per_rotation> * <microsteps> / <steps_per_mm>
|
|
# 200 * 16 / 400 = 8
|
|
rotation_distance: 8
|
|
endstop_pin: !PA11
|
|
# Reduced by a margin of error so that the nozzle doesn't strike the bed
|
|
# when the endstop position shifts due to temperature, see note above.
|
|
# Use Z_ENDSTOP_CALIBRATE and set your own value here.
|
|
position_endstop: 0.0
|
|
position_max: 250
|
|
|
|
[extruder]
|
|
step_pin: PD6
|
|
dir_pin: PD3
|
|
enable_pin: !PB3
|
|
microsteps: 16
|
|
# full_steps_per_rotation: 200
|
|
# rotation_distance = <full_steps_per_rotation> * <microsteps> / <steps_per_mm>
|
|
# Note: the FOKOOS default Marlin e-steps are 94.0, but my testing based on
|
|
# measuring the actual length of filament fed when 100mm was requested, found 96.9
|
|
# to be more accurate.
|
|
# 200 * 16 / 96.9 = 33.02
|
|
rotation_distance: 33.02
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PC3
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC1
|
|
control: pid
|
|
# Tuned at 200C.
|
|
pid_Kp: 35.789
|
|
pid_Ki: 2.339
|
|
pid_Kd: 136.892
|
|
min_temp: 5
|
|
max_temp: 275
|
|
|
|
[heater_bed]
|
|
heater_pin: PA0
|
|
sensor_type: EPCOS 100K B57560G104F
|
|
sensor_pin: PC0
|
|
control: watermark
|
|
min_temp: 5
|
|
max_temp: 150
|
|
|
|
[fan]
|
|
pin: PB1
|
|
|
|
[filament_switch_sensor filament_sensor]
|
|
switch_pin: !PA4
|
|
|
|
# This is needed if you are using Arc Welder.
|
|
[gcode_arcs]
|
|
|
|
# BLtouch configuration. Uncomment these blocks if you have installed a
|
|
# BLtouch. The correct wiring is to use the Robin Nano's BLtouch port for the
|
|
# 3-wire connector (make sure you connect it the right way round) and the Z+
|
|
# endstop port for the 2-wire connector (use the innermost 2 pins, center is
|
|
# ground). Follow Klipper's instructions for installing and calibrating the
|
|
# BLtouch to set the correct x_offset, y_offset, and z_offset values below.
|
|
# There are headers available for the BLtouch on the right hand side of the
|
|
# toolhead, behind the fan cover. Check the connections carefully with a
|
|
# multimeter before using them. The wiring can be done through the ribbon
|
|
# cables, by connecting a BLtouch extension to the PCB attached to the
|
|
# left-hand Z stepper motor, but this requires either soldering directly to
|
|
# the PCB (likely easiest), or crimping extra pins into the connector to be
|
|
# found there.
|
|
#
|
|
#[bltouch]
|
|
#sensor_pin: ^PC4
|
|
#control_pin: PA8
|
|
#x_offset: 57
|
|
#y_offset: -18
|
|
#z_offset: 2.5
|
|
|
|
# Optional bed mesh configuration you can use if you have a BLtouch installed.
|
|
#[bed_mesh]
|
|
#mesh_min: 70,15
|
|
#mesh_max: 220,210
|
|
#horizontal_move_z: 5
|
|
#speed: 150
|