mirror of https://github.com/Desuuuu/klipper.git
172 lines
7.3 KiB
INI
172 lines
7.3 KiB
INI
# This file serves as documentation for config parameters of
|
|
# additional devices that may be configured on a printer. The snippets
|
|
# in this file may be copied into the main printer.cfg file. See the
|
|
# "example.cfg" file for description of common config parameters.
|
|
|
|
|
|
# In a multi-extruder printer add an additional extruder section for
|
|
# each additional extruder. The additional extruder sections should be
|
|
# named "extruder1", "extruder2", "extruder3", and so on. See the
|
|
# "extruder" section in example.cfg for a description of available
|
|
# parameters.
|
|
#[extruder1]
|
|
#step_pin: ar36
|
|
#dir_pin: ar34
|
|
#...
|
|
#deactivate_gcode:
|
|
# A list of G-Code commands (one per line) to execute on a G-Code
|
|
# tool change command (eg, "T1") that deactivates this extruder and
|
|
# activates some other extruder. It only makes sense to define this
|
|
# section on multi-extruder printers. The default is to not run any
|
|
# special G-Code commands on deactivation.
|
|
#activate_gcode:
|
|
# A list of G-Code commands (one per line) to execute on a G-Code
|
|
# tool change command (eg, "T0") that activates this extruder. It
|
|
# only makes sense to define this section on multi-extruder
|
|
# printers. The default is to not run any special G-Code commands on
|
|
# activation.
|
|
|
|
|
|
# Multi-stepper axes. On a cartesian style printer, the stepper
|
|
# controlling a given axis may have additional config blocks defining
|
|
# steppers that should be stepped in concert with the primary
|
|
# stepper. One may define any number of sections with a numeric suffix
|
|
# starting at 1 (for example, "stepper_z1", "stepper_z2", etc.).
|
|
#[stepper_z1]
|
|
#step_pin: ar36
|
|
#dir_pin: ar34
|
|
#enable_pin: !ar30
|
|
#step_distance: .005
|
|
# See the example.cfg for the definition of the above parameters.
|
|
#endstop_pin: ^ar19
|
|
# If an endstop_pin is defined for the additional stepper then the
|
|
# stepper will home until the endstop is triggered. Otherwise, the
|
|
# endstop will home until the endstop on the primary stepper for the
|
|
# axis is triggered.
|
|
|
|
|
|
# Heater cooling fans (one may define any number of sections with a
|
|
# "heater_fan" prefix). A "heater fan" is a fan that will be enabled
|
|
# whenever its associated heater is active. In the event of an MCU
|
|
# software error the heater_fan will be set to its max_power.
|
|
#[heater_fan my_nozzle_fan]
|
|
# See the "fan" section for fan configuration parameters.
|
|
#pin: ar4
|
|
# The remaining variables are specific to heater_fan.
|
|
#heater: extruder
|
|
# Name of the config section defining the heater that this fan is
|
|
# associated with. The default is "extruder".
|
|
#heater_temp: 50.0
|
|
# A temperature (in Celsius) that the heater must drop below before
|
|
# the fan is disabled. The default is 50 Celsius.
|
|
#fan_speed:
|
|
# The fan speed (expressed as a value from 0.0 to 1.0) that the fan
|
|
# will be set to when its associated heater is enabled. The default
|
|
# is max_power.
|
|
|
|
|
|
# Additional micro-controllers (one may define any number of sections
|
|
# with an "mcu" prefix). Additional micro-controllers introduce
|
|
# additional pins that may be configured as heaters, steppers, fans,
|
|
# etc.. For example, if an "[mcu extra_mcu]" section is introduced,
|
|
# then pins such as "extra_mcu:ar9" may then be used elsewhere in the
|
|
# config (where "ar9" is a hardware pin name or alias name on the
|
|
# given mcu).
|
|
#[mcu my_extra_mcu]
|
|
# See the "mcu" section in example.cfg for configuration parameters.
|
|
|
|
|
|
# Servos (one may define any number of sections with a "servo"
|
|
# prefix). The servos may be controlled using the SET_SERVO g-code
|
|
# command. For example: SET_SERVO SERVO=my_servo ANGLE=180
|
|
#[servo my_servo]
|
|
#pin: ar7
|
|
# PWM output pin controlling the servo. This parameter must be
|
|
# provided.
|
|
#maximum_servo_angle: 180
|
|
# The maximum angle (in degrees) that this servo can be set to. The
|
|
# default is 180 degrees.
|
|
#minimum_pulse_width: 0.001
|
|
# The minimum pulse width time (in seconds). This should correspond
|
|
# with an angle of 0 degrees. The default is 0.001 seconds.
|
|
#maximum_pulse_width: 0.002
|
|
# The maximum pulse width time (in seconds). This should correspond
|
|
# with an angle of maximum_servo_angle. The default is 0.002
|
|
# seconds.
|
|
|
|
|
|
# Statically configured digital output pins (one may define any number
|
|
# of sections with a "static_digital_output" prefix). Pins configured
|
|
# here will be setup as a GPIO output during MCU configuration.
|
|
#[static_digital_output my_output_pins]
|
|
#pins:
|
|
# A comma separated list of pins to be set as GPIO output pins. The
|
|
# pin will be set to a high level unless the pin name is prefaced
|
|
# with "!". This parameter must be provided.
|
|
|
|
|
|
# Statically configured PWM output pins (one may define any number of
|
|
# sections with a "static_pwm_output" prefix). Pins configured here
|
|
# will be setup as PWM outputs during MCU configuration.
|
|
#[static_pwm_output my_output_pwm]
|
|
#pin:
|
|
# The pin to configure as PWM output. This parameter must be
|
|
# provided.
|
|
#value:
|
|
# The value to statically set the PWM output to. This is typically
|
|
# set to a number between 0.0 and 1.0 with 1.0 being full on and 0.0
|
|
# being full off. However, the range may be changed with the 'scale'
|
|
# parameter (see below). This parameter must be provided.
|
|
#hard_pwm:
|
|
# Set this value to force hardware PWM instead of software PWM. Set
|
|
# to 1 to force a hardware PWM at the fastest rate; set to a higher
|
|
# number to force hardware PWM with the given cycle time in clock
|
|
# ticks. The default is to use software PWM.
|
|
#cycle_time: 0.100
|
|
# The amount of time (in seconds) per PWM cycle when using software
|
|
# based PWM. The default is 0.100 seconds.
|
|
#scale:
|
|
# This parameter can be used to alter how the 'value' parameter is
|
|
# interpreted. If provided, then the 'value' parameter should be
|
|
# between 0.0 and 'scale'. This may be useful when configuring a PWM
|
|
# pin that controls a stepper voltage reference. The 'scale' can be
|
|
# set to the equivalent stepper amperage if the PWM were fully
|
|
# enabled, and then the 'value' parameter can be specified using the
|
|
# desired amperage for the stepper. The default is to not scale the
|
|
# 'value' parameter.
|
|
|
|
|
|
# Statically configured AD5206 digipots connected via SPI bus (one may
|
|
# define any number of sections with an "ad5206" prefix).
|
|
#[ad5206 my_digipot]
|
|
#enable_pin:
|
|
# The pin corresponding to the AD5206 chip select line. This pin
|
|
# will be set to low at the start of SPI messages and raised to high
|
|
# after the message completes. This parameter must be provided.
|
|
#channel_1:
|
|
#channel_2:
|
|
#channel_3:
|
|
#channel_4:
|
|
#channel_5:
|
|
#channel_6:
|
|
# The value to statically set the given AD5206 channel to. This is
|
|
# typically set to a number between 0.0 and 1.0 with 1.0 being the
|
|
# highest resistance and 0.0 being the lowest resistance. However,
|
|
# the range may be changed with the 'scale' parameter (see
|
|
# below). If a channel is not specified then it is left
|
|
# unconfigured.
|
|
#scale:
|
|
# This parameter can be used to alter how the 'channel_x' parameters
|
|
# are interpreted. If provided, then the 'channel_x' parameters
|
|
# should be between 0.0 and 'scale'. This may be useful when the
|
|
# AD5206 is used to set stepper voltage references. The 'scale' can
|
|
# be set to the equivalent stepper amperage if the AD5206 were at
|
|
# its highest resistance, and then the 'channel_x' parameters can be
|
|
# specified using the desired amperage value for the stepper. The
|
|
# default is to not scale the 'channel_x' parameters.
|
|
|
|
|
|
# Replicape support - see the generic-replicape.cfg file for further
|
|
# details.
|
|
#[replicape]
|