mirror of https://github.com/Desuuuu/klipper.git
160 lines
4.6 KiB
INI
160 lines
4.6 KiB
INI
# This file contains pin mappings and other appropriate default parameters
|
|
# for a Wanhao Duplicator i3 v2.1 and its clones
|
|
# (Monoprice Maker Select, Cocoon Create, etc.)
|
|
# See the files example.cfg and example-extras.cfg for a description of available parameters.
|
|
#
|
|
# This will probably work on older revisions (v1.0, v2.0) of the printer
|
|
# but is untested on those versions.
|
|
#
|
|
# For best results with klipper and the Wanhao Duplicator i3, follow these
|
|
# guidelines:
|
|
#
|
|
# - Flash a bootloader to the Melzi board in the printer
|
|
# See http://www.instructables.com/id/Using-an-Arduino-to-Flash-the-Melzi-Board-Wanhao-I/
|
|
#
|
|
# - Make sure the auto-reset jumper is *enabled* on the Melzi board
|
|
# (See step 1 in the bootloader tutorial above)
|
|
#
|
|
# - Locate the USB serial port for your printer in /dev/serial/by-id/ format.
|
|
# See https://github.com/KevinOConnor/klipper/blob/master/docs/FAQ.md#wheres-my-serial-port
|
|
# It will be something like:
|
|
# /dev/serial/by-id/usb-FTDI_FT232R_USB_UART_ABCD1234-if00-port0
|
|
#
|
|
# - Configure klipper to compile firmware for the AVR atmega1284p
|
|
#
|
|
# - At this point, "make flash FLASH_DEVICE=..." should successfully
|
|
# flash your printer board. Use the /dev/serial/by-id/ format for
|
|
# FLASH_DEVICE to ensure consistent results.
|
|
# See https://github.com/KevinOConnor/klipper/blob/master/docs/FAQ.md#the-make-flash-command-doesnt-work
|
|
# if you have problems.
|
|
#
|
|
# - Copy this sample file you are currently reading to ~/printer.cfg,
|
|
# and customize the following parameters:
|
|
# * [extruder] > step_distance
|
|
#
|
|
# This is the inverse of "E steps" (extruder steps per mm) from the stock
|
|
# Wanhao Repetier-based firmware.
|
|
# (See https://3dprinterwiki.info/extruder-steps/ )
|
|
#
|
|
# For example, if your E-steps are set to 107.0 steps per mm,
|
|
# then step_distance should be (1 / 107.0) ~= .009346
|
|
#
|
|
# * [extruder] > PID parameters (pid_Kp, pid_Ki, pid_Kd)
|
|
# * [heater_bed] > PID parameters (pid_Kp, pid_Ki, pid_Kd)
|
|
#
|
|
# PID values from stock Wanhao firmware (Repetier) do not
|
|
# translate directly to klipper. You will need to run klipper's
|
|
# PID autotune function for the extruder and bed. After getting the
|
|
# klipper firmware up and running, run the M303 autotune procedures
|
|
# by sending these commands via octoprint terminal (one per autotune):
|
|
#
|
|
# extruder: M303 E0 S<temp>
|
|
# heated bed: M303 E-1 S<temp>
|
|
#
|
|
# After the autotune process completes, PID parameter results
|
|
# can be found in the Octoprint terminal tab (if you're quick)
|
|
# or in /tmp/klippy.log.
|
|
#
|
|
# Enter the PID parameters into the appropriate sections of ~/printer.cfg .
|
|
#
|
|
# * [extruder] > max_temp
|
|
# * [heater_bed] > max_temp
|
|
#
|
|
# The max temps included in this printer config are limited to 230 for extruder
|
|
# and 70 for heated bed. If your printer has been modified to handle higher temps
|
|
# (like an upgraded hot end or a separate MOSFET for your heated bed), you may
|
|
# want to increase these values.
|
|
#
|
|
# * [mcu] > serial
|
|
#
|
|
# Enter the USB serial port of the printer in /dev/serial/by-id/ format
|
|
# for best results.
|
|
#
|
|
# - Power cycle the Wanhao Duplicator i3
|
|
#
|
|
# - Issue the command "RESTART" via the Octoprint terminal tab (similar to
|
|
# how you would send a manual gcode command, but send the word RESTART).
|
|
# This tells klipper to reload its config file and do an internal reset.
|
|
# You should then see a status screen appear on the printer's LCD.
|
|
#
|
|
# - Be sure to follow these instructions before attempting any prints:
|
|
# https://github.com/KevinOConnor/klipper/blob/master/docs/Config_checks.md
|
|
|
|
[stepper_x]
|
|
step_pin: PD7
|
|
dir_pin: PC5
|
|
enable_pin: !PD6
|
|
step_distance: .0125
|
|
endstop_pin: ^!PC2
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 40
|
|
|
|
[stepper_y]
|
|
step_pin: PC6
|
|
dir_pin: PC7
|
|
enable_pin: !PD6
|
|
step_distance: .0125
|
|
endstop_pin: ^!PC3
|
|
position_endstop: 0
|
|
position_max: 200
|
|
homing_speed: 40
|
|
|
|
[stepper_z]
|
|
step_pin: PB3
|
|
dir_pin: !PB2
|
|
enable_pin: !PA5
|
|
step_distance: 0.0025
|
|
endstop_pin: ^!PC4
|
|
position_endstop: 0.5
|
|
position_max: 180
|
|
homing_speed: 2
|
|
|
|
[extruder]
|
|
step_pin: PB1
|
|
dir_pin: !PB0
|
|
enable_pin: !PD6
|
|
step_distance: .009346
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.750
|
|
heater_pin: PD5
|
|
sensor_type: NTC 100K beta 3950
|
|
sensor_pin: PA7
|
|
control: pid
|
|
pid_Kp: 18.214030
|
|
pid_Ki: 0.616380
|
|
pid_Kd: 134.556146
|
|
min_temp: 0
|
|
max_temp: 230
|
|
|
|
[heater_bed]
|
|
heater_pin: PD4
|
|
sensor_type: NTC 100K beta 3950
|
|
sensor_pin: PA6
|
|
control: pid
|
|
pid_Kp: 71.321
|
|
pid_Ki: 1.989
|
|
pid_Kd: 639.210
|
|
min_temp: 0
|
|
max_temp: 70
|
|
|
|
[fan]
|
|
pin: PB4
|
|
|
|
[mcu]
|
|
serial: /dev/ttyUSB0
|
|
restart_method: command
|
|
|
|
[printer]
|
|
kinematics: cartesian
|
|
max_velocity: 200
|
|
max_accel: 1000
|
|
max_z_velocity: 2
|
|
max_z_accel: 100
|
|
|
|
[display]
|
|
lcd_type: st7920
|
|
cs_pin: PC1
|
|
sclk_pin: PD3
|
|
sid_pin: PC0
|