| .. |
|
__init__.py
|
klippy: Add support for dynamic loading of python modules
|
2018-01-28 12:19:26 -05:00 |
|
ad5206.py
|
spicmds: Rework SPI message transmission
|
2018-05-07 09:10:34 -04:00 |
|
adc_temperature.py
|
adc_temperature: Support defining custom sensors in the config file
|
2018-04-09 15:44:34 -04:00 |
|
bed_tilt.py
|
probe: Move code from bed_tilt and delta_calibrate into ProbePointsHelper
|
2018-05-20 11:41:07 -04:00 |
|
delta_calibrate.py
|
probe: Move code from bed_tilt and delta_calibrate into ProbePointsHelper
|
2018-05-20 11:41:07 -04:00 |
|
display.py
|
Display M73-indicated progress plus linear ETA on ST7920 displays.
|
2018-05-23 20:46:17 -04:00 |
|
fan.py
|
fan: Allow the fan shutdown_speed to be configured
|
2018-05-18 19:12:03 -04:00 |
|
gcode_macro.py
|
gcode_macro: Add the ability to define custom g-code macros
|
2018-05-25 12:40:06 -04:00 |
|
heater_bed.py
|
heater: Add PrinterHeaters class that stores all sensors and heaters
|
2018-04-04 23:13:53 -04:00 |
|
heater_fan.py
|
fan: Allow the fan shutdown_speed to be configured
|
2018-05-18 19:12:03 -04:00 |
|
homing_override.py
|
homing_override: Add axes config parameter
|
2018-06-11 20:41:18 -04:00 |
|
multi_pin.py
|
pins: Remove module level get_printer_pins() and setup_pin() functions
|
2018-04-04 12:26:39 -04:00 |
|
output_pin.py
|
output_pin: Fix SET_PIN max_val check
|
2018-06-05 09:12:31 -04:00 |
|
pid_calibrate.py
|
pid_calibrate: Make sure to unregister new control class on error
|
2018-04-06 11:39:24 -04:00 |
|
probe.py
|
Extras: Probing does reply with the z position where the probe triggers.
|
2018-06-13 22:34:25 -04:00 |
|
replicape.py
|
linux: Convert linux SPI code to use the generic spicmds.c code
|
2018-05-07 09:10:34 -04:00 |
|
servo.py
|
servo: Use new gcode.register_mux_command()
|
2018-05-20 12:40:10 -04:00 |
|
static_digital_output.py
|
static_digital_output: Add static_digital_output section to extras/
|
2018-03-17 13:06:51 -04:00 |
|
stepper_buzz.py
|
stepper_buzz: Convert to iterative solver
|
2018-06-20 09:26:10 -04:00 |
|
temperature_fan.py
|
temperature_fan: Fix issue 403 use max_speed
|
2018-06-19 11:51:07 -04:00 |
|
thermistor.py
|
thermistor: Add Honeywell 100K and MGB18 thermistor definitions
|
2018-04-30 16:08:17 -04:00 |
|
tmc2130.py
|
tmc2130: Allow the PWMCONF register to be configured
|
2018-05-25 11:38:27 -04:00 |
|
verify_heater.py
|
verify_heater: Disable when writing output to a debug file
|
2018-06-08 23:51:41 -04:00 |
|
virtual_sdcard.py
|
gcode: Raise an error if a duplicate command is registered
|
2018-05-20 13:08:22 -04:00 |
|
z_tilt.py
|
z_tilt: Add support for Z_TILT_ADJUST
|
2018-05-22 22:23:44 -04:00 |
eb73b5d0b0