The SET_GCODE_OFFSET command could cause unwanted behavior when an
offset is applied to the following g-code command. (In particular,
when the following command is an extrude only move - as in
issue #1289.)
Don't apply the offset immediately. Instead, add support for a MOVE=1
parameter which will schedule a move to apply the given offset.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Prior to the BLTouch v3, the recommended command times were 700us
(pin_down), 1200us (touch_mode), 1500us (pin_up), 1800us (self_test),
and 2200us (reset). However, the recommended Marlin timing (via servo
"angles") was 647.111, 1162.667, 1472, 1781.333, and 2193.778us.
As of the BLTouch v3, the recommended times are now 650, 1165, 1475,
1780, and 2190us. The v3 continues to recommended Marlin timings of
647.111, 1162.667, 1472, 1781.333, and 2193.778us.
Update Klipper to use the new BL-Touch v3 recommended timing. The new
timings are required for the BL-Touch v3 and they are closer to what
the Marlin firmware has historically used.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Improve the precision of soft pwm pulses by allowing the host to
directly specify the clock duration of the pulse. This improvement in
precision may be noticeable when controller servos (and bltouch).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Mark methods internal to gcode.py with an underscore so that it is
easier to see which functions are purely helper functions.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
There are reports that SPI does not work correctly on the Fysetc F6 if
the PB0 (sdcard cs enable line) isn't pulled high. Update the default
config to enable that line.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
"The z_tilt_adjust was coded to require 3 points because the original
intent was for railcore-xl and voron. Since then, a number of users
have started using z_tilt_adjust for prusa i3 style printers with dual z
steppers. That's fine, but we just haven't gotten around to removing
the superfluous check in the code." -- Kevin O'Connor
remove that check.
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
Factor out minimum required points check for ProbePointsHelper
in prep for setting different values for quad_gantry_level
and z_tilt_adjust
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
Use /tmp/klippy.log in the install script - all the documentation
currently uses that file location.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
"Feed Filament" menu item value was off-screen that made this item useless. So I changed its name to just "Feed". Users shall easily guess that this item is for filament feeding because this item is located in "Filament" menu.
Signed-off-by: Alexander Fadeev <alfsoft@gmail.com>
This config is based on the existing Ender 3 example config but some of
the directions for the steppers have been reversed. It works for me so
far, but feel free to modify.
Signed-off-by: Billy Jones <billyajones@gmail.com>
Minor updates to the kit-zav3d-2019.cfg to make it look more like
other config files: specify the micro-controller type, use the
klipper3d.org site for documentation links, avoid using SAVE_CONFIG
sections in the example configs, add config to printers.test.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Zav3d - a popular russian corexy plywood printer.
Official web site is https://www.zav3d.ru/
Social network community is https://vk.com/zav3d
Signed-off-by: Nurmukhamed Artykaly <nurmukhamed.artykaly@hdfilm.kz>
safety feature that prevents quad_gantry_level from trying to do a
correction that might break things - if your probe fires early for
whatever reason and tries to do an 8mm correction in one corner instead
we abort if a correction is over a configurable limit by default 4mm
configurable via `max_adjust` parameter in the config
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
In particular trying to keep the output from a single quad_gantry_level
so that it fits in the octoprint terminal window without the need to
scroll
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
Kevin O'Connor
fess
LyleCheatham
Stephan
alfsoft
Matt Baker
Billy Jones
Nurmukhamed Artykaly