The extrude_factor and extruder position are specific to the current
extruder, so reset them to default values on a Tn command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's common to add commands that dispatch to a particular object
instance depending on the value of a command parameter. (For example,
the command "SET_SERVO SERVO=xyz" wants to be handled by the
particular "xyz" servo instance.) Add a register_mux_command() helper
to gcode.py make it easier to do this.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The M206 command is confusing (it uses negative offsets) and isn't
very flexible. Add a new SET_GCODE_OFFSET command to make it easier
to add virtual offsets to gcode commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The M206 command is confusing as positive values in that command
result in negative offsets to future g-code commands. Perform the
parameter negation in the M206 command instead of storing it that way
internally.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Drop support for M303 and PID_TUNE, and replace it with a new
PID_CALIBRATE command. Move the logic for this command from heater.py
to a new pid_calibrate.py file in the extras/ directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It looks like OctoPrint is expecting the result from M114 to be
relative to the last G92 command. Also, introduce GET_POSITION to
report the actual location that the printer is at.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Report the first line of a multi-line error message twice - once as
part of the informational content, and once with the "!!" error
prefix.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for displaying basic status information on ST7920 and
HD44780 based LCDs that are attached directly to a micro-controller.
Signed-off-by: Marcio Teixeira <marcio@alephobjects.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for directly printing from a local file on the host. This
may be useful if the host cpu is not fast enough to run OctoPrint
well.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of using the toolhead class to determine if stats should be
reported, allow every printer object with a stats() callback to
determine if stats are needed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
OctoPrint (and other software) will sometimes send additional commands
even if the previous command has not yet responded with an "ok".
Change the g-code input reading code to keep reading input so that an
M112 can be detected (and processed out-of-order). To avoid the
extreme case where one writes an entire g-code file to the input
without any pacing, disable the input reading if more than 20 commands
are pending.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the script being run raises an error, then stop running that script
and return the error to the caller.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of hardcoding which objects are called on state transitions,
allow any "printer object" to be invoked if it has a printer_state()
method. Convert connect, ready, shutdown, and disconnect callbacks to
this mechanism.
Similarly, allow all printer objects to provide a stats() callback.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add get_reactor(), lookup_object(), lookup_module_objects(), and
set_rollover_info() to the main Printer class so that callers do not
need to peek into the class' members. Similarly, add get_printer()
and get_name() methods to the ConfigWrapper class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If register_command() is passed None as the function to call, then
treat it as an unregister command request.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the existing reset_last_position() code in cmd_G28() instead of
manually implementing the logic.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Group commands by category instead of listing them in numerical
order. This is just code movement; no code changes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the homing logic out of toolhead.py and into homing.py. This
simplifies the toolhead logic and centralizes the homing code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that commands can be registered dynamically, move the code for
SET_SERVO from gcode.py to the PrinterServo() class in chipmisc.py.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Translate caught exceptions into a gcode.error() exception. This way
there is one standard place to invoke respond_error(). Also, always
reset the last_position on a handled error.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If an MCU signals a shutdown from the background thread, notify the
main thread and handle the shutdown there. Dispatch shutdown handling
from the main Printer() class instead of from the Toolhead class.
This simplifies the shutdown logic.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Continue to sample the ADC input pins even if the MCU goes into a
shutdown state. This enables the printer to continue reporting
temperatures even on an mcu error.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Build a single (very large) logging message with the debug state.
This prevents the output from being fragmented.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit d0932009 changed the way command handling was performed, and
commit 95950949 fixed a defect in that commit. Unfortunately, the fix
was incomplete.
If multiple commands were sent to Klippy without waiting for an "ok"
response from Klippy, then it was possible for those additional
commands to be queued and processed after subsequent commands. This
would result in commands being processed out of order.
Fix this by only reregistering the input fd in the greenlet that
performs the unregistration of the fd.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Store pertinent information from the software startup in a dictionary
that the various printer components can access instead of in
individual variables in the Printer() class. This makes it easier to
add future command-line options.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Wait for any pending moves to be fully handled before exiting. Make
sure the wait is done inside the "self.is_processing_data" check to
avoid infinite recursion. Don't keep reading from the file while
waiting to exit.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit d0932009 introduced an error that could cause lost input in
cases where the sender did not wait for an "ok" message before sending
the next command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't modify dictionaries while iterating them and be careful to use
// when doing an integer divide.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The set_printer_ready() can be called from a background thread on a
shutdown event, so don't try to lookup the printer components in that
case. Simplify build_handlers() so that it no longer tests for
components being available - test for component availability in the
command handlers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
No need to recommend users disable "SD card support" in octoprint -
instead, just ignore the M21 command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Advice users to issue a FIRMWARE_RESTART command on a printer shutdown
event, and remove support for CLEAR_SHUTDOWN. A full mcu reset is
preferable and it simplifies the interface.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't force a firmware shutdown on a simple gcode parse error.
Instead, report the error back to the user and otherwise ignore the
command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add initial support for micro-controller resets via the Arduino reset
mechanism. Also, automatically attempt a firmware restart if the
printer CRC does not match.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the user requests a restart and the machine appears to be otherwise
functioning normally, then attempt to stop the heaters and fans prior
to restarting the host. This prevents the firmware from going into a
shutdown state when the heater is on and the host restarts.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The normal system clock can have sudden jumps if the system clock is
changed. Use the system monotonic clock to avoid these sudden changes
in time.
It appears the Raspbian OS (which is used by OctoPi) is setup to
update the system clock upon network connectivity. This could cause
sudden system clock changes which could lead to Klippy processing
errors. Using the monotonic clock eliminates these issues.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When testing via a gcode input file, it's easier to debug problems if
the program exits upon the first exception.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If a speed is never specified then default to 25mm/s (up from 1 mm/s).
If a user accidentally issues a move without setting the speed, the
default speed shouldn't be so slow that it takes minutes to finish the
move.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a "restart" gcode command that will cause the host "klippy"
software to reload its config and restart.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support human readable commands (eg, "help"). Add a "help" command to
list these extended commands.
Also, add support for declaring command aliases, command help, and
command availability next to the handlers themselves.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The set_printer_ready() method can be called from a background thread.
Have the main Printer class call a new dump_debug() method in the main
thread on a shutdown event.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Setup the reactor and run the MCU connection code as a timer within
the reactor. The connection code will make use of reactor greenlets
so that it can wait for events during the connection phase.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't expose the ADC initialization to the gcode and heater code -
instead, register a callback within the MCU_adc class and call it
directly from the MCU class after configuration completes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Instead of checking the endstop trigger directly after a retract move,
verify some distance is traveled during the following homing
operation. This reduces the amount of synchronization between mcu and
host during homing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Should a homing move complete without hitting the endstop, then
disable motors, disable the endstop checking, and report the error to
the user.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Create the Homing class in the gcode handler instead of in the
kinematic classes. This will make it easier to pass error messages
back to the user.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Create the QueryEndstops in the gcode handler instead of in the
kinematic classes. This simplifies the gcode handler as it can
directly register its response callback.
Also, store the stepper name in the stepper class. Also, propagate
the print_time of the query request to the mcu_endstop class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the printer is commanded to an invalid location, reset the current
position to the last successfully commanded position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor