Convert all users of the printer_state("connect") handler to register
a "klippy:connect" event handler instead.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Convert all users of the printer_state("ready") handler to register a
"klippy:ready" event handler instead.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Convert all users of the printer_state("shutdown") handler to register
a "klippy:shutdown" event handler instead.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
- changes that make easier to use menu as module UI
- new helper method for delayed callbacks
- method for getting the menu instance from display
- new action for sending menu:action events
- allow_without_selection option for cards
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
- long press with timer (button release is not needed anymore)
- initial support for edit mode long press gcode
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
The sam3 i2c code and the linux code use a 7-bit i2c address, while
the avr, lpc176x, and samd21 i2c code uses an 8-bit address with the
least significant bit always zero. A similar issue occurred in the
host code (sx1509.py and replicape.py use 7-bit addresses while
uc1701.py and mcp4451.py use 8-bit addresses).
Consistently use 7-bit addresses in all the code. This breaks
compatibility between host and mcu software, so make a change to the
config_i2c command to force users to synchronize software updates.
This also breaks common Smoothieboard configs, so update the mcp4451
code to validate the i2c_address.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
As discussed in #1057, the default loading- and unloading procedure does
not behave as expected. Setting the extruder to relative mode fixes this.
Signed-off-by: Nils Friedchen <Nils.Friedchen@googlemail.com>
If an SPI device is shared among many devices, then all the device's
CS pins should be set high prior to setting up the clk pin.
(Otherwise, there's a chance a device could interpret the clk pin
setup as part of a transmission.)
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
I have made one change to `gcode.py` to support quoted parameter
values.
I have added support for the basic `M118` command (see
https://reprap.org/wiki/G-code#M118:_Echo_message_on_host). I have
also added a `RESPOND` command that takes extended parameters.
`ECHO` might be a better name than `RESPOND` but is already defined
in `gcode.py`.
Signed-off-by: Alec B. Plumb <alec@etherwalker.com>
Allow an arbitrary gcode_id to be supplied during heater setup. This allows future extras to register additional IDs beyond B, and T#.
Signed-off-by: John Jardine <john@gprime.net>
It appears some bltouch "clones" do not report the probe as triggered
when put in "touch mode" while the pin is raised. Add a config option
to allow users to disable the test.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some of the bltouch implementations may only respond to a probe event
with a 5ms pulse. Make sure to check the signal pin at least every
millisecond to ensure no signal is lost.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
To deal potential z scaling when fade is enabled, a fade_target option has been introduced. This option may either be set to 0.0 or any z position within the range of the mesh. A value of 0.0 will result in previous behavior, where z adjustment phases out until no further adjustment is added. A non-zero value will phase out adjustment until the target has been reached, after which the rest of the print will be offset along the z axis by the fade_target. By default the fade_target will be calculated as an average of the mesh.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Due to various potential issues with fading out z-adjustment, it is better to disable by default and allow users to opt-in.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Add a self.all_framebuffers variable and change self.vram to only
contain the new display data. This allows the main code to access the
self.vram member variable without the need to index for current/old
data. (It also updates the code to match the latest st7920 and
hd44780 code.)
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Cheap mechanical servos have small flickering. When this servo stay on one position, this flickering slowly destroy internal potentiometer and make servo unusable. Many mechanisms need servo only to change position. Therefore I create this minor path to enable/disable servo. It stop pulses for this servo, that's all.
Corresponding G-code is:
SET_SERVO SERVO=config_name [WIDTH=] [ENABLE=<0|1>]
SET_SERVO SERVO=config_name [ANGLE=] [ENABLE=<0|1>]
For example:
SET_SERVO SERVO=touch ANGLE=80 ENABLE=1 ; enable servo and set position
G4 P200 ; wait 200ms
SET_SERVO SERVO=touch ENABLE=0 ; disable servo
This patch add one option to servo configuration:
enable: <False/True> # default True
It not have impact to user code existing already because it is optional parameter and default value is same as original behavior.
Signed-off-by: Jiri Dobry <jdobry@centrum.cz>
Kevin O'Connor
Petri Honkala
Janar Sööt
Master92
Paulo Drugos
Alec B. Plumb
john--
Arksine
Jiri Dobry
James
Lucas Fink