Add a new build definition to note micro-controllers that have strict
timing. The Linux mcu code does not have strict timing - all other
targets currently do.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When enabling "low level options" in Kconfig, selecting a chip that is
20Mhz capable would result in 20Mhz being the default. A 16Mhz speed
is the preferred default, so list that first in the menu.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Make it clear that the name of the constant being defined is a string.
When the value being defined is also a string, use a new
DECL_CONSTANT_STR() macro.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's rare to use all of a target's prerequisites in a recipe - replace
most cases with $< (the target's first prerequisite).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The cpu is almost always 16Mhz and the serial port is almost always
UART0, so no need to prompt in the normal case.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the definition of SERIAL_BAUD to the main src/Kconfig file. Only
show this as an option if the user selects the ability to configure
low-level options.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The sam3 i2c code and the linux code use a 7-bit i2c address, while
the avr, lpc176x, and samd21 i2c code uses an 8-bit address with the
least significant bit always zero. A similar issue occurred in the
host code (sx1509.py and replicape.py use 7-bit addresses while
uc1701.py and mcp4451.py use 8-bit addresses).
Consistently use 7-bit addresses in all the code. This breaks
compatibility between host and mcu software, so make a change to the
config_i2c command to force users to synchronize software updates.
This also breaks common Smoothieboard configs, so update the mcp4451
code to validate the i2c_address.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Simultaneously define the hardware pin and the timer registers. This
makes the table a little easier to understand.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The atmega328p is basically the same as the atmega328 - add explicit
support for it so that avrdude doesn't complain while flashing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The usb_cdc code will arrange to call usb_read_ep0_setup() after a
shutdown, so no need to have an explicit shutdown handler.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Recent code additions have increased the stack usage and it is no
longer clear that everything will fit in 128 bytes. Increase all
targets to 256 bytes (the atmega2560 was already at 256 bytes).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The atmega168 doesn't have enough flash space to fit all features -
disable the "bit banging" interfaces to make room.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The SPI interface needs to be enabled and configured to the correct
settings of a given oid before CS is asserted. The new function
spi_prepare() allows ports to do that.
This port only introduces the new function in all ports with no
implementation and adds the call to the Klipper generic firmware code.
That means everything still works as before. Ports need to be changed
to fix the underlying issue.
Discussion about the motivation here:
https://github.com/KevinOConnor/klipper/pull/453#issuecomment-403131149
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
The AVR requires that the SS pin be an output pin for correct SPI
operation. Some boards use the SS pin to control devices separate
from SPI, however. Don't change the output level if the pin is
already an output, and prefer setting it low if it is not already an
output pin.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Prefer using 'uint8_t' buffers as it is too easy to run into C sign
extension problems with 'char' buffers. Prefer using 'uint_fast8_t'
for buffer lengths as gcc does a better job compiling them on 32bit
mcus.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The gpio_out_toggle() function in the sam3x8e and stm32f1 code was
only valid if it was called with irqs disabled.
Commits 018c5daa and 9c52ad43 enabled the lcd code which called
gpio_out_toggle() with irqs enabled. This could cause corruption of
the gpio state.
Introduce a gpio_out_toggle_noirq() function that will only be invoked
with irqs disabled, and fix gpio_out_toggle() on sam3x8e and stm32f1
so that it safe to call even if irqs are enabled.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Improve the SPI message transmit system. Add support for bus speed
and bus mode. Add support for sending SPI messages on shutdown.
Signed-off-by: Petri Honkala <cruwaller@gmail.com>
Signed-off-by: Douglas Hammond <wizhippo@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The AVR chips (bizarrely) start an ADC conversion when entering Idle
mode. This behavior can cause the ADC to be busy when a sample is
required. Worse, if a series of events cause the cpu to enter and
leave Idle mode with a timing similar to the ADC checking rate then it
can cause the ADC to show as busy for extended periods. This could
cause high MCU load and possibly lead to a "Rescheduled timer in the
past" shutdown.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't logically or the ADSC bit on the start of a conversion -
explicitly set the full contents of the register. Also, clear the
ADIF flag on each write.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Define unique register aliases for all of the hardware serial port
definitions. This makes it easier to deal with the AVR chips that use
different register names.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Extract out common code from avr/serial.c, sam3x8e/serial.c, and
stm32f1/serial.c into a new generic/serial_irq.c file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Arksine
Pascal Albert
Grigori Goronzy