The digital output commands implement a subset of the software pwm
commands. Change the host code to just use the software pwm commands
and simplify the micro-controller code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The HSI48 clock on the stm32f042 isn't as accurate as the main HSI
clock. So, only use the HSI48 clock when using USB to synchronize
that clock.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The code isn't actually capable of altering the mux registers due to
hardware checks enforced by the chip. Disable that code to save a few
bytes in the final binary.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the buffer pointer can't fit in a uint32_t then pass a relative
buffer offset instead. This fixes buffer handling on 64bit linux
mcus.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a helper function to convert from a string buffer passed in the
args[] parameter to an actual pointer. This avoids all the callers
needing to perfrom pointer manipulation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Restore the default of an 8KiB bootloader for stm32f103 and a 32KiB
bootloader for stm32f207/stm32f407.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Improved CAM bus ID generation, there were issues with ID collisions.
Added a small fast hash library.
Signed-off-by: Pontus Borg <liquidpontus@yahoo.se>
Only write "1" to the "enable" file when a non-zero pwm width is
requested. Write "0" to the "enable" file when a zero pwm width is
requested.
This fixes a problem on the replicape servo lines that prevented them
from being fully disabled.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The lpc176x hardware spi initialization code was swapping the CPOL and
CPHA bits. This caused the MAX31865 and MAX31856 chips to not work
correctly.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Reworked the STM32F0 CAN bus implementation. It's more robust and higher performance.
Added support for function remapping to different pins. API is emulating an STM32F0.
Improved and ported CAN bus to STM32F0, F1 and F4.
Signed-off-by: Pontus Borg <glpontus@gmail.com>
Initial support for stm32f2 in general and STM32F207 in particular.
Boots up and communicates on STM32F207VC.
Signed-off-by: Boleslaw Ciesielski <combolek@users.noreply.github.com>
Use 2us in the linux timer dispatch code to unify linux timer dispatch
logic with the common timer_irq.c code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the product/vendor id to 0x1d50/0x614e, which has been reserved
for Klipper (thanks to the openmoko project).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
On the Linux mcu, toggling the pin after the time is read is not
valid. Make that optimization dependent on CONFIG_HAVE_STRICT_TIMING.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a new build definition to note micro-controllers that have strict
timing. The Linux mcu code does not have strict timing - all other
targets currently do.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Matt Shepcar
Kevin O'Connor
Pascal Pieper
bondus
Guy Shapira
Cabia Rangris
bondus
combolek
kianusch
Lucio Tarantino
Arksine
andryblack