This file includes the build instructions and generic configuration for the TH3D EZBoard Lite v2.0 3d printer control board.
Signed-off-by: Anthony Dellett <anthony.dellett@gmail.com>
With recent changes, the extruder_stepper may be used for new
purposes, and synchronizing to the "extruder" motion queue at startup
may become a confusing default.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This command is a rename of SYNC_STEPPER_TO_EXTRUDER. This change is
in preparation for the removal of SYNC_STEPPER_TO_EXTRUDER.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This commit contains a configuration for the Anycubic Vyper printer from 2021.
It uses a clone of the STM32F103 chip named GD32F103.
There are 2 Mainboard versions out there v0.0.5 and v0.0.6, this config has
been tested with the v0.0.6 only. It should probably work for v0.0.5 as well
since there are no different changes in the Anycubic Marlin firmware.
The LCD is not supported yet (might work, but didn't try yet).
Signed-off-by: Marc Neuhaus <marc@neuhaus.nrw>
Signed-off-by: Manuel Fichtner <manuel.fichtner@me.com>
This config I created and fully tested on my own printer Anycubic 4Max Pro 2.0. This works fine! Please note that this printer is different from the Anycubic 4MAX.
Signed-off-by: Alexander Usachev <int_0x21@protonmail.com>
This config was a community effort and was author and tested by sihawken, 3D.Subzwari & dapostol73.
Signed-off-by: Demetrius Apostolopoulos <dapostol73@hotmail.com>
Information and some lines verbatim were sourced from the official BigTreeTech Octopus
GitHub repository to make this configuration as well as existing configurations in the same
folder as this one
Signed-off-by: Charles Pickering <charles.pickering@live.com>
Support the rp2040 (as tested on a Raspberry Pi Pico board). This
adds basic uart, timer, gpio, and watchdog support.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Adds Duet3 Mini Config with support for expansion header
Signed-off-by: Luke Ashley <Luke@Lukeslab.online>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
To support continuous belt printing, add nestable repeat
loop support via an `[sdcard_loop]` module.
Supported G-Code:
- SDCARD_LOOP_BEGIN COUNT=n ; Loop for N times, or infinitely if N is 0
- SDCARD_LOOP_END ; End of loop
- SDCARD_LOOP_DESIST ; Complete all loops without iterating
Marlin M808 compatibility example in `config/sample-macros.cfg`:
- M808 Ln ; Loop for N times, or infinitely if N is 0
- M808 ; End of loop
- M808 K ; Complete all loops without iterating
Added unit tests in test/klippy/sdcard_loop.test
See https://reprap.org/wiki/G-code#M808:_Set_or_Goto_Repeat_Marker
Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
Add support for the Creality CR-30 'PrintMill', and its base board,
the Creality v4.2.10.
Add them to the `test/klippy/printers.test` test suite
Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
This is useful when a saved bed mesh is used to ensure that the bed level
has not drifted too far from where it was when the mesh was created.
Signed-off-by: Johannes Stuettgen <johannes.stuettgen@gmail.com>
Kevin O'Connor
Alex Maclean
SyrasX
Spencer Owen
Apulo
just-trey
Lorenzo
adelyser
gjsmo
Manuel Fichtner
Peter Pan's Techland
int_0x03
Pedro Lamas
Demetrius Apostolopoulos
charlespick
charlespick
Joseph Orduna
github@matthewlloyd.net
Luke's Lab
Jason S. McMullan
Tircown
George Fu
Johannes Stuettgen