The purpose of this PR is to add an installation script to klipper for use on Centos. Several packages names are different from debian based installs, and the system service is handled via systemd rather than LSB.
Signed-off-by: Alan Weinstock <pyroballpcs@gmail.com>
Add virtualenv, build-essential, gcc-arm-none-eabi, and
binutils-arm-none-eabi packages - just in case they aren't already
installed. Reported by @AxMod3DPrint.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This change will make the "PROBE" command actually reply with the
z-position where the probe triggers. As this command is called
internally for the BED_TILT_CALIBRATE and Z_TILT_ADJUST those commands
will also give a response while probing, which I see as advantage over
the silent operation.
This change also lets one define some gcode for a repeatable probing
test to meassure the quality of the sensor and overall probing accuracy.
Signed-off-by: Hans Raaf <hr-klipper@oderwat.de>
Added a config parameter to define the homing override axes. This way
one can still home x and y axis without the z-probe cycle coming in the
way.
Signed-off-by: Hans Raaf <hr-klipper@oderwat.de>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The python-dev package is usually already installed, but there's no
harm in stating it explicitly. Reported by @yschroeder.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Disable the verify_heater checks when debugging, as otherwise it can
cause failures when processing files in batch mode.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The printer uses the TriGorilla board which is an
AVR ATmega2560 Arduino + RAMPS compatible board.
The diplay is a RepRapDiscount Smart Controller 2004 compatible one.
Signed-off-by: Peter Ruevski <dpr@ruevs.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add config/kit-voron2-2018.cfg - a sample configuration file for the
Voron2 printer. Based on config file from "Maglin".
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When using multiple micro-controllers it may be necessary to use an id
from /dev/serial/by-path/ instead of /dev/serial/by-id/. Also,
emphasize that in config/example-multi-mcu.cfg.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
In some rare circumstances it was possible for the host software to
become so busy that it does not transmit a get_clock request for
several seconds. (In particular, this could occur with some complex
calls to coordinate_descent.) If that happened, it was possible for
the code to incorrectly report a "Timeout with MCU" error. Rework the
is_active() check to prevent that.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Apply the changes made by a SET_GCODE_OFFSET command to the next move,
even if the move is relative to the last movement. This allows the
command to implement "babystepping" requests.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the get_status command to get_clock. Don't report the shutdown
status in the new get_clock command.
The primary purpose of this change is to force the host code to report
a firmware version mismatch with older firmwares as recent changes
(namely the ordering of message block acks) have subtle
incompatibilities if different host/mcu code is used.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Normally, the MCU is restarted on a config change. However, that
should not be done automatically if the MCU is in a shutdown state.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the mcu is using a traditional serial port, then only send a new
message block if there is space available in the mcu receive buffer.
This should make it significantly less likely that high load on the
mcu will result in retransmits.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Send the ack after processing commands - this gives the host code more
information on serial buffer utilization.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Prefer using 'uint8_t' buffers as it is too easy to run into C sign
extension problems with 'char' buffers. Prefer using 'uint_fast8_t'
for buffer lengths as gcc does a better job compiling them on 32bit
mcus.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If a section name had mixed case it would cause an incorrect error
during the section/option config checking.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add the ability to add a custom g-code command that in turn executes
one or more configured g-code commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
pyr0ball
Douglas Hammond
Oli
Hans Raaf
ruevs
Michael Barbour
cruwaller