Now that the PrinterStepper and MCU_stepper classes have been merged,
there is no need for the add_to_endstop() method.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't default to a Z location of 10, as that could cause damage if the
probe's z_offset is greater than 10. Instead, use the "retract
distance" method that is used for normal multi-sample probing.
Update the PROBE_ACCURACY command parameter names to use the same
parameter names as the PROBE command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add PROBE_SPEED, SAMPLES, SAMPLE_RETRACT_DIST, SAMPLES_TOLERANCE,
SAMPLES_TOLERANCE_RETRIES, and SAMPLES_RESULT parameters to the PROBE
command (and to commands that indirectly invoke a probe).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Factor out _calc_mean() and _calc_median() functions and call from
both run_probe() and cmd_PROBE_ACCURACY().
This also fixes a subtle error in the run_probe() median function - on
some kinematics the x and y position can change on a z move so the x
and y should be taken from the z probe values actually used.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This changes the config file so that the configuration of
multi-samples is now done in the [probe] (and [bltouch]) section
instead of the various delta, bed_mesh, z_tilt, etc. config sections.
With this change, PROBE and PROBE_CALIBRATE commands now also utilize
multi-sampling.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Factor out minimum required points check for ProbePointsHelper
in prep for setting different values for quad_gantry_level
and z_tilt_adjust
Signed-off-by: John "Fess" Fessenden <fess@fess.org>
The z_offset calculation should have been calculated from the probe
height to the measured bed position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implementation of "PROBE_ACCURACY" to measure the maximum, minimum,
average and standard deviation of a probe.
Signed-off-by: Rui Caridade <rui.mcbc@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the logic for performing the second home from the kinematics
classes to the generic homing code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't require (or permit) the user to specify a stepper_z
position_endstop when using the probe:z_virtual_offset mechanism. In
that case the position_endstop should always equal the probe's
z_offset - so no need to have the user specify it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't require the config file to specify manual probing. Instead,
allow the user to select manual probing on each ProbePointsHelper
invocation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that all the callers of ProbePointsHelper take a cartesian
coordinate for the probe locations, it's possible to perform averaging
of multi-sample probes within the class. This simplifies the callers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Only call cmd_NEXT() for manual probing. This simplifies the code as
the automatic probing and manual probing have slightly different
probing mechanisms.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that all users of ProbePointsHelper use the same
get_probed_position() code, it is possible to implement that locally
within the ProbePointsHelper class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the name of the config registration method and pass an explicit
reference to the callback to the new method. This makes the
relationship between mcu registration and build_config() more clear in
the calling code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Call lift-z prior to the first move. This prevents the nozzle from hitting the build surface in situations that home the nozzle off and below the bed.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Only check the probe's z_offset against the stepper_z endstop position if the probe is used as a virtual endstop.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Don't pass pin_type to lookup_pin() - instead, if a pin can be
inverted or can have a pullup, then the caller must explicitly specify
that when calling lookup_pin(). This simplifies the code for the
cases where it is not valid to invert or pullup.
Explicitly pass the pin_type to setup_pin() and have ppins.setup_pin()
apply default pullup and invert flags.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The different uses of get_position() can be confusing, so choose a
different name for the ProbePointsHelper callback.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Julien Lirochon
fess
Rui Caridade
Rui Caridade
Arksine
Romain “Artefact2” Dal Maso