Tweak the AVR register pressure optimization in reschedule_timer() to
optimize it further. This improves the performance of AVR timers when
there are several pending timers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rework the timer prioritization code so that is compares against the
current time instead of the number of repeat timers in a given
interrupt. This makes the code slightly faster and it should provide
better protection against task starvation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Increase the size of the serial receive buffer. With transmit rates
of 250000 baud, it only takes a little over a millisecond to overflow
the existing buffer.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename get_homed_position() to get_homed_offset() and return the
endstop position delta in steps instead of an absolute position
relative to position_endstop. The conversion to absolute positions
can be dependent on the type of kinematics in use, so is inappropriate
to do in the low level stepper.py code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the printer is commanded to an invalid location, reset the current
position to the last successfully commanded position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow a config file to specify 'min_extrude_temp: 0' to disable the
minimum extrude temperature test. This makes it easier to perform
testing on the avr simulator.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 0685802c changed the query endstop timeout to use host time
instead of the mcu clock. However, it is possible for an endstop
homing request to be in the future which makes using the host time
inappropriate. Revert back to using the mcu clock to determine when
to send an endstop query.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's theoretically possible for floating point truncation to cause a
math formula to return a small negative number instead of 0. If
sqrt() is called on this small negative number it could cause a
crash. Check for this case and return 0.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 47f30331 converted compress_bisect_add() to use "best reach"
instead of "best add". However, that change caused
compress_bisect_add() to behave poorly when passed in invalid data
(negative times). Change the code to better handle invalid data.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow the config file to specify the minimum temperature for the
extruder and check for that temperature prior to moving the extruder
motor.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce a check_move() method in the extruder and cartesian
kinematic classes. This allows the lower level classes to verify the
contents of the move prior to queing that move.
The speed and acceleration handling for special Z and extrude only
moves are also moved from the generic toolhead class to the low-level
classes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Search for the maximum reachable value instead of the maximum "add".
The maximum reachable value encompasses both the maximum count and a
closest step time to the last requested step time. This allows for
more "add=0" sequences to be generated which the mcu can optimize for.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's possible for a "count=1" stepper move immediately after a
set_next_step_dir or reset_step_clock command to be valid and have an
interval less than min_stop_interval. Make sure this case does not
result in a shutdown.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When doing serial file output debugging, write the config commands as
they are often useful to inspect.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Generate the data dictionary in out/klipper.dict on each build. This
makes it easier to use the dictionary when debugging.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for enhancing the precision of endstop switches by also
inspecting the phase of the stepper motor when the endstop triggers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some details on the code flow and organization have changed since
support for ARM processors was added. Update Code_Overview.md
accordingly.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rework the code so that the kinematic class (currently just
cartesian.py) has more control over the homing process.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a config option to define an amount of additional filament to feed
into the extruder during acceleration and deceleration of the
extruder. This can help ensure plastic is deposited in the correct
places during a print.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Only skip acceleration between moves if both moves perform a similar
amount of extrusion. This ensures the extruder has sufficient time to
accelerate to and from each extrude move.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow the owner of the stepper object to cacluate the maximum step
jerk velocity. This is used to ensure there is no communication error
between mcu and host.
Disable checking of jerk velocity for extruder stepper motors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Store the baud rate the MCU is configured for in the "identify" data
and use that rate when calculating the baudadjust parameter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The test to check if the queue only needed to be moved was not correct
and it could lead to a segfault if clean_queue() was called instead of
actually increasing the queue size.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Check for an invalid count and report an error if found. This
prevents some segfaults when count goes negative.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Create a new python file (extruder.py) to control the extruder heater
and stepper motors. This separates the extruder control logic from
the cartesian robot code - making it easier to customize both the
kinematic control of the robot as well as the extruder.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
All users of max_step_velocity and max_step_accel end up multiplying
by step_dist anyway, so it's easier to store max_velocity and
max_accel.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Explicitly check for when the move_queue is empty and only call
move.calc_junction() when there is a previous move. This avoids the
need to create a dummy "sentinal" move object and it simplifies the
code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Remove the lookahead.py file and move its code directly into
toolhead.py. The MoveQueue() class is small and tightly coupled to
the toolhead code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor