Update callers to use the printer.command_error reference instead of
directly using homing.CommandError() when raising or catching errors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
There's no reason to distinguish between an EndstopError and a
CommandError, so just use CommandError.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rework extruder.get_trapq() into extruder.sync_stepper() so that
extruder_stepper.py does not need to directly access the extruder
internals.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename try_load_module() so that it uses consistent naming for
"printer objects". Change the function to raise an error by default
if the specified module does not exist.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The heater logic is an independent module that does not need to be
treated as part of the "core" klipper code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The print_time parameter of heater.set_temp() is not currently used
and it isn't necessary to flush the look-ahead queue just get the
print_time. Remove the parameter from heater.set_temp() to avoid
flushing the look-ahead queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The builtin Tn command is not sufficiently flexible to control some
multi-extruder printers. Remove the command and encourage users to
define individual gcode_macros for each Tn instance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implement the pressure advance calculations while performing the
definitive integral calculations. This simplifies both the
extruder.py and kin_extruder.c code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the extruder lookahead method is no longer used it can be
removed from the toolhead and extruder classes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support averaging the extruder position over a time range to "smooth
out" the velocity changes that occur during pressure advance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for kinematic functions that calculate step times based on
a range of the motion queue. This requires adding additional pause
times when fully flushing the motion queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Directly disable all the stepper motors on a global motor_off() from
the StepperEnable() class in stepper_enable.py. This simplifies the
toolhead and kinematic classes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
No longer allow the primary extruder to be named "extruder0". This
avoids internal and external confusion between the printer objects and
config section names.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Do not apply max_extrude_cross_section check, and do apply
extrude_only_xxx checks to Z only moves that also extrude. Some
printer start scripts will prime the extruder while moving the Z.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Calculate the ratio of axis distance to total move distance (axis_d /
move_d) and store in a new member variable axes_r. This avoids
needing to recalculate the value in other code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that all callers use the trapq system to queue moves, it is no
longer necessary to individually allocate and fill a 'struct move'.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow an arbitrary gcode_id to be supplied during heater setup. This allows future extras to register additional IDs beyond B, and T#.
Signed-off-by: John Jardine <john@gprime.net>
Some users increase max_extrude_cross_section to avoid issues with
some slicers. However, increasing that value also increases the
defaults for the max_extrude_only parameters which is not obvious.
Base the max_extrude_only defaults only on the configured nozzle
diameter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allocate the stepper_kinematics directly in mcu.py - that way the
kinematic classes don't have to interact with the chelper code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move extruder.py, cartesian.py, corexy.py, and delta.py to a new
kinematics/ sub-directory. This is intended to make adding new
kinematics a little easier.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
David Smith
Simo Apell
Janar Sööt
john--