Now that all users of ProbePointsHelper use the same
get_probed_position() code, it is possible to implement that locally
within the ProbePointsHelper class.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's possible (and a little simpler) to use cartesian coordinates when
calculating a stable position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Configure the tmc2208 during the 'connect' phase so that a problem
during configuration is properly raised as a config error. Catch
errors during DUMP_TMC and raise them as g-code errors.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't log a heater verification error if that error is due to the
printer being shutdown for some other reason. Those spurious error
reports can be confusing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
No need to report an error if the M73 is not between 0 and 100 - just
display the nearest valid value.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support using SAVE_CONFIG to store the results of DELTA_CALIBRATE to
the printer config file. Store the low level probe measurements in
the config as well.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the "stable position" logic from the delta.py kinematics code to
the delta_calibrate.py calibration code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for writing back the main printer config file with
additional calibration data stored in it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add write_glyph() support to hd44780.py. Update uc1701.py and
st7920.py to support writing single character glyphs via
write_glyph().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the st7920 icon rendering optimizations from display.py to
st7920.py. This simplifies the code for other displays.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It isn't necessary to use the st7920's xor capabilities when drawing
the bed heating animations. This makes it easier to use the icons for
other displays.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a command that will turn off all heaters in the printer. Run this
command in the default idle_timeout action.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If an arm is nearly parallel to the bed then that tower's carriage may
have a velocity up to 3 times greater than the toolhead's maximum
velocity (relative to the print). Take that into account when
calculating the stepper's maximum halt velocity.
This fixes some rare "No next step" shutdowns on delta printers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit 4573932f allowed move.end_pos to differ from the requested end
position - the toolhead class should use the updated position when
storing its commanded position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's possible that a g-code transform class may make an extrude only
move appear as a kinematic move due to limitations of double precision
math. Handle this by checking for an inconsequential move distance
instead of checking for a move distance of exactly zero.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Log the details of the MCU prior to attempting to configure the MCU.
This way, the log contains the MCU information even if a configuration
error occurs.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Change the name of the config registration method and pass an explicit
reference to the callback to the new method. This makes the
relationship between mcu registration and build_config() more clear in
the calling code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Janar Sööt
Maks Zolin
Florian Heilmann
Arksine