Calculate the "homing position" using the endstop trigger time instead
of the position of the steppers.
This is in preparation for multi-mcu homing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The section-index plugin can cause some confusing navigation. Use the
simpler site navigation for now.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Added optional PROFILE parameter to allow bed_mesh_calibrate to
save the mesh directly into the provided profile name instead of
default. If omitted, it will be stored in default.
Signed-off-by: Randell L Hodges <rhodges@taxfodder.com>
Fix reference to neopixel color_data in status reference documentation
so the given example works as expected.
Signed-off-by: Matt Heath <hello@mattheath.com>
The atmega328pb has officially named these pins as PE2 and PE3, so use
that naming scheme instead of the previous Klipper invented names.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Try to keep the host mcu_position synchronized with the
micro-controller by querying during startup and after every homing
event.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Look for lines that don't start with a list and don't start with a
space to check for the end of a list. This fixes the rendering of the
list in BLTouch.md .
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Just a quick cleanup to where I flubbed the Z_OFFSET_APPLY_ENDSTOP and Z_OFFSET_APPLY_PROBE documentation
Signed-off-by: Ben Eastep <shifting@shifting.ca>
Restore old link behavior - each document file will have a single html
file ending in the ".html" suffix.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
- Keeps the markdown inside the code blocks as is
- Logs the modified lines (mkdocs serve —verbose)
Signed-off-by: Damien Martin <damlobster@gmail.com>
whilst this line is in Measuring_Resonances.md, users following this guide for other reasons have no cause reason to read that and don't have an explanation for what they didn't know they didn't do.
Signed-off-by: Rowland Straylight <rowlandstraylight@gmail.com>
Created two new extended gcodes: Z_OFFSET_APPLY_ENDSTOP, and Z_OFFSET_APPLY_PROBE.
These use the z gcode offset to revise the probe offset, or z endstop position
allowing users to make a frequently used babystepping value permanent without
manual config editing.
Signed-off-by: Ben Eastep <shifting@shifting.ca>
Document change in behavior of the controller_fan module.
Lookup heater objects in connect() event handler.
Return list of stepper names from stepper_enable.get_steppers().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allows contoller_fan sections to monitor only certain steppers instead of
all of them, similar to how heaters are currently handled.
Signed-off-by: Sophie Hirn <sophie.hirn@wyvernscale.com>
Do not infer the sercom from the config section name, as that
prevents one from using SPI buses on multiple samd mcus.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
- Add dual_carriage abilities for hybrid-corexy and hybrid-corexz
- Introduce the module idex_mode
- Fix add_stepper to the correct rail in hybrid-corexy
Signed-off-by: Fabrice GALLET <tircown@gmail.com>
Sometimes an automated filament load is implemented,
but extruder might not always extrude filament.
This adds a flag to check if this operation is possible.
Signed-off-by: Kamil Trzcinski <ayufan@ayufan.eu>
If a high UART frequency is used to communicate with TMC2208/TMC2209
drivers then it may not be possible for Klipper to communicate with
the drivers until they are reset. Note this in the troubleshooting
document.
Reported by @matthewlloyd.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The default pid_integral_max setting should be sufficient; it's not
necessary to complicate the documentation and config to support
customization.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Randell Hodges
Matt Heath
Damien
shiftingtech
strayr
Sophie Hirn
Martin
Dmitry Butyugin
Tircown
Matthew Lloyd
Kamil Trzcinski
Eric Callahan
Alex Zellner