The builtin Tn command is not sufficiently flexible to control some
multi-extruder printers. Remove the command and encourage users to
define individual gcode_macros for each Tn instance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implement the pressure advance calculations while performing the
definitive integral calculations. This simplifies both the
extruder.py and kin_extruder.c code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the extruder lookahead method is no longer used it can be
removed from the toolhead and extruder classes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support averaging the extruder position over a time range to "smooth
out" the velocity changes that occur during pressure advance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for kinematic functions that calculate step times based on
a range of the motion queue. This requires adding additional pause
times when fully flushing the motion queue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update code that modifies the low-level kinematics handlers to first
call toolhead.flush_step_generation().
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename calc_position() to calc_tag_position() and have it calculate
the value of the position from the last stepper set_tag_position()
call. This enables the calc_tag_position() code to be more flexible
as it can be run with arbitrary positions.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that the PrinterStepper and MCU_stepper classes have been merged,
there is no need for the add_to_endstop() method.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Directly disable all the stepper motors on a global motor_off() from
the StepperEnable() class in stepper_enable.py. This simplifies the
toolhead and kinematic classes.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
No longer allow the primary extruder to be named "extruder0". This
avoids internal and external confusion between the printer objects and
config section names.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Do not apply max_extrude_cross_section check, and do apply
extrude_only_xxx checks to Z only moves that also extrude. Some
printer start scripts will prime the extruder while moving the Z.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Calculate the ratio of axis distance to total move distance (axis_d /
move_d) and store in a new member variable axes_r. This avoids
needing to recalculate the value in other code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that all callers use the trapq system to queue moves, it is no
longer necessary to individually allocate and fill a 'struct move'.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that all kinematics use the trapq system, there is no need to call
into the kinematics on each g-code move.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that homing is implemented via "drip moves", it is no longer
necessary to round the homing speed and it is no longer necessary to
add a delay for cpu processing time.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Due to the corexy kinematics, the individual steppers may have a
velocity of sqrt(2) times faster than the cartesian velocity _and_ can
have an acceleration of sqrt(2) times faster. Make sure to calculate
in the higher acceleration.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Allow an arbitrary gcode_id to be supplied during heater setup. This allows future extras to register additional IDs beyond B, and T#.
Signed-off-by: John Jardine <john@gprime.net>
Commit 459e5219 added a special case to the boundary checks to permit
homing moves. In some cases, the second home retract could also be
outside the normal boundary checks - extend the special case to also
permit that move.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Some users increase max_extrude_cross_section to avoid issues with
some slicers. However, increasing that value also increases the
defaults for the max_extrude_only parameters which is not obvious.
Base the max_extrude_only defaults only on the configured nozzle
diameter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
When a delta printer has different arm lengths or different endstop
positions then the homing position falls outside of the normal
printable area. Add a special check to the range checking code to
permit this move instead of homing to a position near the actual
homing position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move the logic for performing the second home from the kinematics
classes to the generic homing code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit b0d859f2 introduced a second_homing_speed parameter, and it
also changed the retract speed. Revert the retract speed change (use
homing_speed when the head retracts).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Commit b0d859f2 introduced a second_homing_speed parameter; that
parameter needs to also be constrained to the max_z_velocity.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Florian Heilmann
Janar Sööt
john--