This reverts commit 70ea0806d9.
The above commit breaks software spi on linux hosts. Revert that
commit until an improved error check can be implemented.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The timer_read_time() call can be expensive - when the next timer is
definitely pending, avoid making that call.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implement rescheduling math using the simple 32-bit timer instead of
the Unix timespec struct. This makes the code simpler and doesn't
adversely impact the overall performance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Initial commit of code to support 1-wire (Dallas) sensors such
as the DS18B20. Requires Linux kernel drivers to create a file
in /sysfs which is read by this module, and temperature
typically returned to a temperature_fan.
Signed-off-by: Alan Lord <alanslists@gmail.com>
Signed-off-by: Josh Headapohl <joshhead@gmail.com>
If the buffer pointer can't fit in a uint32_t then pass a relative
buffer offset instead. This fixes buffer handling on 64bit linux
mcus.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Only write "1" to the "enable" file when a non-zero pwm width is
requested. Write "0" to the "enable" file when a zero pwm width is
requested.
This fixes a problem on the replicape servo lines that prevented them
from being fully disabled.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use 2us in the linux timer dispatch code to unify linux timer dispatch
logic with the common timer_irq.c code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The beagleboard TI kernel 4.14 and 4.19 contain a commit which change
the device names ("pwm: Create device class for pwm channels") from
pwmN to pwm-${chip}:N. This commit was never merged into the upstream
kernel.
Decrease the number of pwm channels to a more reasonable 16. Increase
the number of pwm chips to 8 since the replicape servo pwm outputs are
on pwmchip4.
Update replicape code to detect appropriate channel.
Signed-off-by: Janne Grunau <janne-gh@jannau.net>
Rework the spi_config commands so that bus configuration and shutdown
message configuration is done separately from the main "config_spi"
command. This makes the spi configuration more flexible. It's now
possible to use software spi without a CS pin. It's now possible to
define multiple SPI messages to send on a shutdown event.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The replicape servo pins (P9_14/P9_16) are muxed to the SOCs hardware
PWM unit driven by a 13MHz GP timer. They have to be driven by the
linux host mcu. This commits adds hardware PWM support using the linux
sysfs user space interface.
Signed-off-by: Janne Grunau <janne-3d@jannau.net>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Make it clear that the name of the constant being defined is a string.
When the value being defined is also a string, use a new
DECL_CONSTANT_STR() macro.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The SPI interface needs to be enabled and configured to the correct
settings of a given oid before CS is asserted. The new function
spi_prepare() allows ports to do that.
This port only introduces the new function in all ports with no
implementation and adds the call to the Klipper generic firmware code.
That means everything still works as before. Ports need to be changed
to fix the underlying issue.
Discussion about the motivation here:
https://github.com/KevinOConnor/klipper/pull/453#issuecomment-403131149
Signed-off-by: Grigori Goronzy <greg@chown.ath.cx>
Prefer using 'uint8_t' buffers as it is too easy to run into C sign
extension problems with 'char' buffers. Prefer using 'uint_fast8_t'
for buffer lengths as gcc does a better job compiling them on 32bit
mcus.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The gpio_out_toggle() function in the sam3x8e and stm32f1 code was
only valid if it was called with irqs disabled.
Commits 018c5daa and 9c52ad43 enabled the lcd code which called
gpio_out_toggle() with irqs enabled. This could cause corruption of
the gpio state.
Introduce a gpio_out_toggle_noirq() function that will only be invoked
with irqs disabled, and fix gpio_out_toggle() on sam3x8e and stm32f1
so that it safe to call even if irqs are enabled.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the generic spi send/receive code on Linux. Update the replicape
code to use the updated command format.
Also, update the replicape code to turn off the stepper motors on a
shutdown event.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Only open the watchdog device after the console has been opened. The
machine should not reboot in the unlikely event the console can't be
opened.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Continue to sample the ADC input pins even if the MCU goes into a
shutdown state. This enables the printer to continue reporting
temperatures even on an mcu error.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Update the scripts used to install and "flash" the pru
micro-controller code. Also, add a "flash" script for the linux
micro-controller code. This makes it easier to install Klipper on a
Beaglebone board that uses a Replicape.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for reading analog values via the standard Linux IIO
interface. This can be used on Replicape boards to sample analog
input pins.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for sending SPI messages to devices via the standard Linux
SPI interface. This can be used to configure the shift registers on
Replicape boards.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for controlling pca9685 PWM drivers using the standard
Linux I2C interface. The pca9685 device is found on Replicape boards.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for compiling the Klipper micro-controller code as a
real-time process capable of running on standard Linux systems.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Evgeny Chukreev
Alan Lord
Lucio Tarantino
andryblack
Janne Grunau
Arksine
Janne Grunau
Ricardo Amezquita
Grigori Goronzy