Before this change, a `CANCEL_PRINT` set a `print_stats` to `paused`
that would later be workaround-ed with `fluidd`/`mainsail` to re-define
`CANCEL_PRINT`.
This sets a proper canceled state, but additionally closes a file
from a `virtual_sdcard` context for `canceled`/`error`, as this is no longer
resumable from this point.
Signed-off-by: Kamil Trzcinski <ayufan@ayufan.eu>
Sometimes an automated filament load is implemented,
but extruder might not always extrude filament.
This adds a flag to check if this operation is possible.
Signed-off-by: Kamil Trzcinski <ayufan@ayufan.eu>
Separate out trsync handling from endstop handling in mcu.py code.
Enable the low-level trdispatch C code.
This is in preparation for multi-mcu homing.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add ability to run C code directly from the low-level socket reading
thread. This enables host based low-latency handlers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The BED_MESH_OFFSET gcode can be used to apply X and/or Y offsets the the mesh lookup. This allows printers with independent extruders to correct the Z adjustment when changing a tool.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
This is a temporary offset applied to the mesh used to fade toward a "target". For clarity, apply the fade offset when the final z calculation is made.
SIgned-off-by: Eric Callahan <arksine.code@gmail.com>
This is useful for macros that'd like to skip QGL if already leveled,
e.g.:
```
{% if not printer.quad_gantry_level.applied %}
QUAD_GANTRY_LEVEL
{% endif %}
```
Signed-off-by: Michael Rose <elementation@gmail.com>
neopixel: add sync param to prevent waking toolhead
dotstar: refactor to match neopixel methods and add sync parameter
Signed-off-by: Paul McGowan <mental405@gmail.com>
Add help description to HELP
Add help description to RESPOND
Add help description to MEASURE_AXES_NOISE, TEST_RESONANCES and SHAPER_CALIBRATE
Add help description to PAUSE, RESUME, CLEAR_PAUSE and CANCEL_PRINT
Add help description to GET_POSITION
Add help description to SET_RETRACTION and GET_RETRACTION
Signed-off-by: Stefan Dej <meteyou@gmail.com>
Pass a print_time instead of a clock to get_past_commanded_position().
Fix calculation on steppers that home and use an inverted direction
pin.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
To support continuous belt printing, add nestable repeat
loop support via an `[sdcard_loop]` module.
Supported G-Code:
- SDCARD_LOOP_BEGIN COUNT=n ; Loop for N times, or infinitely if N is 0
- SDCARD_LOOP_END ; End of loop
- SDCARD_LOOP_DESIST ; Complete all loops without iterating
Marlin M808 compatibility example in `config/sample-macros.cfg`:
- M808 Ln ; Loop for N times, or infinitely if N is 0
- M808 ; End of loop
- M808 K ; Complete all loops without iterating
Added unit tests in test/klippy/sdcard_loop.test
See https://reprap.org/wiki/G-code#M808:_Set_or_Goto_Repeat_Marker
Signed-off-by: Jason S. McMullan <jason.mcmullan@gmail.com>
Allow a larger velocity, accel, and square_corner_velocity than what
is specified in the config file.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The min_stop_interval safety check is fragile and leads to a notable
amount of complexity. Avoid these issues by not programming this
safety check.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
On some kinematics it's possible for the XY position to change
slightly during a probing move. Return back to the original XY
position on a probe lift so each probe attempt starts at the same
nominal position.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Matthew Lloyd
Kamil Trzcinski
Eric Callahan
Dmitry Butyugin
Michael Rose
Paul McGowan
Stefan Dej
Alex Zellner
Florian Heilmann
Jason S. McMullan
Dany Yanev
Tircown