Update the stm32f1 code to the latest from ST. Merge the
lib/cmsis-stm32f1/ and lib/hal-stm32f1/ into a single lib/stm32f1/
directory. Document all the differences from the pristine upstream
code.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It's not necessary to fully build up the look-ahead queue prior to
starting a "drip move" homing operation. Instead, allow the
look-ahead queue to flush normally.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the homing move is exceptionally long, it could take a long time
for the host to process the look-ahead queue. Delay the print_time
calculation until moves are ready to be sent.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rename the commands.
The main reason for this change is to force a micro-controller code
updated (due to important bugfix in 7fefe52d).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
If the move is not added to the move queue, then the SF_LAST_DIR
setting must not be changed. Otherwise, it could result in an
incorrect direction being set on the stepper after a homing operation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The popular "LPC17xx-DFU-Bootloader" alters the LPC_UART0->FDR
register, so be sure to reset it back to its default when using serial
in Klipper.
Reported by @b-vs.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The current z_hop support did not work correctly with common slicers
that change Z height between retract and unretract, and it did not
work correctly with slicers that issue a retract at the end of a print
and then at the beginning of the next print.
The z_hop support is therefore being removed until these issues can be
fixed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't default to a Z location of 10, as that could cause damage if the
probe's z_offset is greater than 10. Instead, use the "retract
distance" method that is used for normal multi-sample probing.
Update the PROBE_ACCURACY command parameter names to use the same
parameter names as the PROBE command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that homing is implemented via "drip moves", it is no longer
necessary for the stepcompress code to have special homing logic.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that homing is implemented via "drip moves", it is no longer
necessary to move the print_time backwards.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Now that homing is implemented via "drip moves", it is no longer
necessary to round the homing speed and it is no longer necessary to
add a delay for cpu processing time.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Rework the low-level implementation of homing movement. The existing
mechanism buffers all homing movement into the micro-controller prior
to starting the home. Replace with a system that buffers all movement
into the host look-ahead buffer and then "drip feed" those moves to
the micro-controllers. Then clear the host look-ahead buffer when all
endstops trigger.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Finish Moves needs be a hard requirement for the event gcodes, as it eliminates the possiblility of an event firing while the gcode is executing.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
It really helps to see a snapshot of available printer variables when building menus and macros. The list of variables always depends on what printer config you have.
Signed-off-by: Janar Sööt <janar.soot@gmail.com>
This moves skew_correction configuration out of printer.cfg. It is now dynamically set by the SET_SKEW gcode.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Kevin O'Connor
Arksine
Janar Sööt