It is preferable to program the tmc drivers with an irun (or cs)
setting near 31, as otherwise the driver may have reduced microstep
precision. It was possible for the driver to be programmed with
irun=16 or irun=17 when it could have been configured with irun=31
with vsense=1 instead. This would occur on tmc2130/tmc2208/tmc2209
drivers for values around 0.900 to 1.000 amps (when using a typical
sense_resistor settings of 0.110 Ohms).
Change the code to prefer using vsense=1 to avoid this issue.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The code automatically reduces the hold_current so that it is no
greater than the run_current. However, this could lead to confusing
behavior if one reduced and then increased the run_current via
SET_TMC_CURRENT commands. To avoid that, this change adds support for
tracking the requested hold_current - thus changes to run_current
don't subtly alter the hold_current.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The Trinamic specs aren't consistent with upper vs lower case, which
can be confusing. Improve clarity by using lower case names
consistently in the code. Register names will continue to use all
upper case naming in the code.
Update the SET_TMC_FIELD command to automatically convert field names
to lower case.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The tmc2130 (and tmc5160) will respond back with the value written
during the next SPI command. Use this feature to verify that the
value written matches the value sent.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Check the status of all Trinamic stepper motor drivers once a second.
If the driver reports an error then invoke a shutdown. Also log any
serious warnings.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The tmc5160 field formatters were mostly duplicates of the tmc2130 -
add the "reset" field to tmc2130.py so both drivers have similar
reporting.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Refactor the tmc driver implementations so that there is a single
implementation of the SET_TMC_CURRENT command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
This patch adds the ability to daisy-chain multiple tmc2130 and
tmc5160 drivers.
Signed-off-by: Marco D'Alessio <marco@wrecklab.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for enabling the stepper via the communication channel.
This improves support for boards with a shared enable line.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
A print_time of zero may translate to a negative clock on a secondary
micro-controller, which would cause an internal error. Change the
code to pass a real print_time or None if it is not needed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Only the tmc2208 driver needs special read register translation logic.
Rework the code so a default implementation is available for all the
other drivers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Introduce TMCMicrostepHelper and TMCStealthchopHelper helper code that
uses the mcu_tmc interface. Update the callers to use these new
helpers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Perform the register initialization directly from TMCCommandHelper and
perform it during the "connect" phase. This unifies the register
setup for the TMC2130, TMC2208, TMC2660, and TMC5160.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the field names from the trinamic specification. This makes the
field similar to all the other driver_XXX config options.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the field helper to simplify the bit manipulation in the driver.
This also enables the extended DUMP_TMC output.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add helper function for reading current, microsteps, and stealthchop
settings from the config file. Use these helpers in both the tmc2130
and tmc2208 modules.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Move these helper functions to the FieldHelper class so that they can
be used by other Trinamic drivers.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Report values of TMC2208 register fields in DUMP_TMC command to help in
tuning and diagnostics.
This also adds functions to refer to register fields by name for TMC drivers
and register mappings for TMC2208.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Signed-off-by: Dmitry Frolov <dmitry.frolov@gmail.com>
Kevin O'Connor
Marco D'Alessio
Trevor Jones
Petri Honkala
Florian Heilmann
Artem Belevich
amblidex
Dmitry Frolov