The M206 command isn't particularly standardized and isn't issued by
default from 3rd party software in their standard configurations.
Encourage users to use the more powerful SET_GCODE_OFFSET command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Support averaging the extruder position over a time range to "smooth
out" the velocity changes that occur during pressure advance.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The current z_hop support did not work correctly with common slicers
that change Z height between retract and unretract, and it did not
work correctly with slicers that issue a retract at the end of a print
and then at the beginning of the next print.
The z_hop support is therefore being removed until these issues can be
fixed.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Don't default to a Z location of 10, as that could cause damage if the
probe's z_offset is greater than 10. Instead, use the "retract
distance" method that is used for normal multi-sample probing.
Update the PROBE_ACCURACY command parameter names to use the same
parameter names as the PROBE command.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add PROBE_SPEED, SAMPLES, SAMPLE_RETRACT_DIST, SAMPLES_TOLERANCE,
SAMPLES_TOLERANCE_RETRIES, and SAMPLES_RESULT parameters to the PROBE
command (and to commands that indirectly invoke a probe).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The SET_GCODE_OFFSET command could cause unwanted behavior when an
offset is applied to the following g-code command. (In particular,
when the following command is an extrude only move - as in
issue #1289.)
Don't apply the offset immediately. Instead, add support for a MOVE=1
parameter which will schedule a move to apply the given offset.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Using .. in the markdown link can confuse some document processors.
Use an absolute link to github instead.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Implementation of "PROBE_ACCURACY" to measure the maximum, minimum,
average and standard deviation of a probe.
Signed-off-by: Rui Caridade <rui.mcbc@gmail.com>
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Adds the ability to register a custom/generic heater through a new extra called heater_generic.
This takes a gcode_id that is reported by M105. Adds a new command to set the temperature for any heater using the syntax:
SET_HEATER_TEMPERATURE HEATER=<heater_name> TARGET=<target_temp>
Signed-off-by: John Jardine <john@gprime.net>
Add updates to example-extras.cfg and G-Codes.md documenting pause_resume. Also add M600 (filament change) to sample-macros.cfg.
Signed-off-by: Eric Callahan <arksine.code@gmail.com>
Add documentation on howto configure the BL-Touch device with
Klipper. A second paragraph addresses possible issues with BL-Touches
Signed-off-by: Wilfried Goesgens <dothebart@citadel.org>
I have made one change to `gcode.py` to support quoted parameter
values.
I have added support for the basic `M118` command (see
https://reprap.org/wiki/G-code#M118:_Echo_message_on_host). I have
also added a `RESPOND` command that takes extended parameters.
`ECHO` might be a better name than `RESPOND` but is already defined
in `gcode.py`.
Signed-off-by: Alec B. Plumb <alec@etherwalker.com>
Cheap mechanical servos have small flickering. When this servo stay on one position, this flickering slowly destroy internal potentiometer and make servo unusable. Many mechanisms need servo only to change position. Therefore I create this minor path to enable/disable servo. It stop pulses for this servo, that's all.
Corresponding G-code is:
SET_SERVO SERVO=config_name [WIDTH=] [ENABLE=<0|1>]
SET_SERVO SERVO=config_name [ANGLE=] [ENABLE=<0|1>]
For example:
SET_SERVO SERVO=touch ANGLE=80 ENABLE=1 ; enable servo and set position
G4 P200 ; wait 200ms
SET_SERVO SERVO=touch ENABLE=0 ; disable servo
This patch add one option to servo configuration:
enable: <False/True> # default True
It not have impact to user code existing already because it is optional parameter and default value is same as original behavior.
Signed-off-by: Jiri Dobry <jdobry@centrum.cz>
Don't require the config file to specify manual probing. Instead,
allow the user to select manual probing on each ProbePointsHelper
invocation.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add support for writing back the main printer config file with
additional calibration data stored in it.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add a command that will turn off all heaters in the printer. Run this
command in the default idle_timeout action.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add initial support for commands that will forcibly move a stepper
(without updating the kinematic classes with the new position).
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The junction_deviation configuration parameter has a number of quirks
that make it difficult to configure. Replace it with a
"square_corner_velocity" configuration parameter.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Add M117 and M73 to the list of supported G-Codes.
Also, remove M117 from the list of commands reported by the HELP
command as that command is typically only used to list "extended
g-code" commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Use the new gcode.register_mux_command() so that SET_PRESSURE_ADVANCE
works correctly with multiple extruders.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
The M206 command is confusing (it uses negative offsets) and isn't
very flexible. Add a new SET_GCODE_OFFSET command to make it easier
to add virtual offsets to gcode commands.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Drop support for M303 and PID_TUNE, and replace it with a new
PID_CALIBRATE command. Move the logic for this command from heater.py
to a new pid_calibrate.py file in the extras/ directory.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
It looks like OctoPrint is expecting the result from M114 to be
relative to the last G92 command. Also, introduce GET_POSITION to
report the actual location that the printer is at.
Signed-off-by: Kevin O'Connor <kevin@koconnor.net>
Kevin O'Connor
Nils Schulte
Arksine
Len Trigg
amblidex
Rui Caridade
Florian Heilmann
Rui Caridade
John Jardine
Wilfried Goesgens
Alec B. Plumb
Jiri Dobry
Michael Barbour